SIST EN 12697-34:2004
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 34: Marshall test
Bituminous mixtures - Test methods for hot mix asphalt - Part 34: Marshall test
This European Standard specifies a test method for determining the stability, flow and the Marshall Quotient values of specimens of bituminous mixtures mixed according to prEN 12697-35 and prepared using the impact compactor method of test EN 12697-30. It is limited to dense graded asphalt concrete and hot rolled asphalt.
Asphalt - Prüfverfahren für Heißasphalt - Teil 34: Marshall-Prüfung
Das Verfahren nach dieser Norm dient zur Bestimmung von Stabilität, Fließwert und Marshall-Quotient von Asphalt-Probekörpern nach prEN (WI 00227118), die mit dem Schlagverdichtungsverfahren der Prüfung prEN (WI 00227046) hergestellt wurden.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 34: Essai Marshall
La présente Norme européenne spécifie une méthode d'essai pour déterminer la stabilité, le fluage et les valeurs du quotient Marshall des éprouvettes de mélanges bitumineux malaxés selon le prEN 12697-35 et compactés a l'aide d'un compacteur a impact selon la EN 12697-30. Elle est limitée aux bétons bitumineux denses et aux " hot rolled asphalt ".
Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 34. del: Preskus po Marshallu
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 34: Marshall testMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 34: Essai MarshallAsphalt - Prüfverfahren für Heißasphalt - Teil 34: Marshall-PrüfungTa slovenski standard je istoveten z:EN 12697-34:2004SIST EN 12697-34:2004en93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-34:200401-september-2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-34June 2004ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part34: Marshall testMélanges bitumineux - Méthodes d'essai pour mélangehydrocarboné à chaud - Partie 34: Essai MarshallAsphalt - Prüfverfahren für Heißasphalt - Teil 34: Marshall-PrüfungThis European Standard was approved by CEN on 1 April 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-34:2004: E
EN 12697-34:2004 (E) 2 Contents page Foreword.3 1 Scope.6 2 Normative references.6 3 Terms and definitions.6 4 Principle.7 5 Apparatus.7 6 Procedure.7 7 Expression of results.8 8 Test report.9 9 Precision.9 Annex A (normative)
Marshall quotient.10 Annex B (normative)
Testing head.11 Bibliography.12
EN 12697-34:2004 (E) 3 Foreword This document (EN 12697-34:2004) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest by August 2005.This European Standard is one of a series of standards as listed below: EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test method for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void characteristics of bituminous specimens EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of the reference density EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactibility EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres
EN 12697-34:2004 (E) 4 EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Partial loss of porous asphalt specimen prEN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or Marshall specimens EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue prEN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test prEN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared by roller compactor EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness of a bituminous pavement EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the adhesivity of binder on pre-coated chippings for HRA prEN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and calibration
EN 12697-34:2004 (E) 5 prEN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content by ignition prEN 12697-40, Bituminous mixtures — Test methods for hot mix asphalt — Part 40: In-situ drainability prEN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icing fluids prEN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of foreign matters in reclaimed asphalt prEN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel The annexes A and B are normative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.