SIST EN 12697-33:2004+A1:2007
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactor
Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactor
This European Standard specifies the methods for compacting parallelepipedal specimens (slabs) of bituminous mixtures, to be used directly for subsequent testing, or from which test specimens are cut.
For a given mass of bituminous mixture, the specimens are prepared either under controlled compaction energy, or until a specified volume and therefore void content is obtained.
This European Standard describes the following methods of compaction:
- pneumatic tyre method,
- steel roller method,
- sliding plates method.
This European Standard is applicable to bituminous mixtures manufactured in the laboratory or in a mixing plant.
Asphalt - Prüfverfahren für Heißasphalt - Teil 33: Probestückvorbereitung mit einem Walzenverdichtungsgerät
Diese Europäische Norm legt die Verfahren für die Verdichtung von quaderförmigen Probekörpern (Platten) aus Asphalt fest, die entweder direkt für die anschließende(n) Prüfung(en) verwendet werden oder aus denen Probekörper geschnitten werden.
Von einem vorgegebenen Asphaltmischgut können Probekörper entweder mit einer geregelten Verdichtungs¬energie oder bis zum Erreichen eines bestimmten Volumens und infolgedessen eines bestimmten Hohlraum¬gehaltes hergestellt werden.
Diese Europäische Norm beschreibt die folgenden Verdichtungsverfahren:
? Luftreifen-Verfahren;
? Stahlwalzen-Verfahren;
? Gleitplatten-Verfahren.
Diese Europäische Norm gilt für Asphalte, die im Labor oder im Asphaltwerk hergestellt wurden.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 33 : Confection d'éprouvettes au compacteur de plaque
Cette Norme européenne spécifie les méthodes de compactage des éprouvettes parallélépipédiques (plaques) de mélanges bitumineux, qui doivent etre utilisées directement pour des essais ultérieurs ou a partir desquelles des éprouvettes sont prélevées.
Pour une masse donnée de mélange bitumineux, les éprouvettes peuvent etre préparées soit a une énergie de compactage contrôlée, soit a volume spécifié, et par conséquent a masse volumique apparente spécifiée.
La présente norme décrit trois méthodes, qui different dans le procédé de compactage :
méthode utilisant une ou deux roues équipées de pneumatiques,
méthode utilisant un rouleau en acier doux,
méthode utilisant une action de cisaillement par des couteaux.
La présente norme s'applique aux mélanges bitumineux fabriqués en laboratoire ou dans une centrale d'enrobage.
Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 33. del: Preskušanci, pripravljeni z valjastim zgoščevalnikom
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactorMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 33 : Confection d'éprouvettes au compacteur de plaqueAsphalt - Prüfverfahren für Heißasphalt - Teil 33: Probestückvorbereitung mit einem WalzenverdichtungsgerätTa slovenski standard je istoveten z:EN 12697-33:2003+A1:2007SIST EN 12697-33:2004+A1:2007en,fr,de93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-33:2004+A1:200701-november-2007
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-33:2003+A1
July 2007 ICS 93.080.20 Supersedes EN 12697-33:2003English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactor
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 33: Préparation des corps d'épreuve au compacteur de plaques
Asphalt - Prüfverfahren für Heißasphalt - Teil 33: Probestückvorbereitung durch Rollenverdichtungsgerät This European Standard was approved by CEN on 3 November 2003 and includes Amendment 1 approved by CEN on 16 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-33:2003+A1:2007: E
EN 12697-33:2003+A1:2007 (E) 2 Contents Page Foreword.3 1 Scope.6 2 Normative references.6 3 Terms, definitions, symbols and abbreviations.6 3.1 Terms and definitions.6 3.2 Symbols and abbreviations.7 4 Principle.8 5 Apparatus.8 5.1 Method using a wheel or two wheels fitted with pneumatic tyres.8 5.2 Methods using a smooth steel roller.9 5.2.1 Smooth steel roller.9 5.2.2 Steel roller used on wheel fitted with pneumatic tyres.10 5.3 Method using a roller running on vertical sliding steel plates.10 6 Preparation.11 6.1 Mass of bituminous mixture.11 6.2 Filling the mould.12 7 Compaction procedure.12 7.1 Method using wheels fitted with pneumatic tyres.12 7.1.1 Test conditions.12 7.1.2 Compaction.12 7.2 Methods using a smooth steel roller.13 7.2.1 General.13 7.2.2 Compaction by a specified energy.13 7.2.3 Compaction with controlled compaction energy.13 7.2.4 Compaction to obtain a specified voids content or compaction degree.14 7.3 Method using a roller running on vertical sliding steel plates.14 7.4 Removing the mould.14 8 Test report.14
EN 12697-33:2003+A1:2007 (E) 3 Foreword This document (EN 12697-33:2003+A1:2007) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2008 and conflicting national standards shall be withdrawn at the latest by January 2008. This document includes Amendment 1, approved by CEN on 2007-05-16. This document supersedes EN 12697-33:2003. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". This European Standard forms a part of a series of tests for mechanical and physical properties of bituminous mixtures as listed below. EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of the void characteristics of bituminous specimens EN 12697-9, Bituminous mixtures — Test methods for hot mix asphalt — Part 9: Determination of the reference density EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactibility EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement
EN 12697-33:2003+A1:2007 (E) 4 EN 12697-14, Bituminous mixture — Test methods for hot mix asphalt — Part 14: Water content EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres EN 12697-17, Bituminous mixture — Test methods for hot mix asphalt — Part 17: Partial loss of porous asphalt specimen EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or Marshall specimen EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue EN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt —Part 27: Sampling EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared by roller compactor EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test EN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness of a bituminous pavement
EN 12697-33:2003+A1:2007 (E) 5 EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the adhesivity of binder on pre-coated chippings for HRA EN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and calibration EN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content by ignition EN 12697-40, Bituminous mixtures — Test methods for hot mix asphalt — Part 40: In situ drainability EN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to deicing fluids EN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of coarse foreign matter in reclaimed asphalt EN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel The applicability of this European Standard is described in the product standards for bituminous mixtures (series of prEN 13108). !deleted text" According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 12697-33:2003+A1:2007 (E) 6 1 Scope This European Standard specifies the methods for compacting parallelepipedal specimens (slabs) of bituminous mixtures, to be used directly for subsequent testing, or from which test specimens are cut. For a given mass of bituminous mixture, the specimens are prepared either under controlled compaction energy, or until a specified volume and therefore void content is obtained. This European Standard describes the following methods of compaction: pneumatic tyre method, steel roller method, sliding plates method. This European Standard is applicable to bituminous mixtures manufactured in the laboratory or in a mixing plant. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling. !EN 12697-35:2004+A1", Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing.
3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1.1 pass one forward or one backward motion of the rolling load 3.1.2 slab axis axis of symmetry of slab parallel to the largest dimension of the mould 3.1.3 lateral axis axis of a pass parallel to largest dimension of a mould; situated at distance a from the slab axis (see Figure 1) 3.1.4 lateral translation distance a between the slab axis and the lateral axis
EN 12697-33:2003+A1:2007 (E) 7
Key 1 Axis 2 Lateral axis 3 Left side 4 Right side
5 Central position 6 Rear position 7 Front position 8 Longitudinal translation of wheels Figure 1 — Sketch plan of a slab, front face of equipment 3.1.5 rear position lateral axis furthest from the front face of the equipment 3.1.6 central position slab axis 3.1.7 front position lateral axis nearest to the front face of the equipment 3.1.8 blocked axis mode equipment operating mode in which the height of the wheel shaft stays constant in relation to the upper edge of mould during a pass 3.1.9 freed axis mode equipment operation mode in which the load applied into the slab remains constant during a pass 3.1.10 sweep plan set of modes by which the wheel(s) pass(es) over the slab;
including order of execution, and extent of lateral translation 3.2 Symbols and abbreviations L is the interior length of mould, in millimetres (mm); l is the interior
width of mould, in millimetres (mm);
EN 12697-33:2003+A1:2007 (E) 8 h is the interior height of mould, in millimetres (mm); M is the mass of slab, in kilograms (kg); ρm is the maximum density of bituminous mixture, in kilograms per cubic metre (kg/m3); ν is the voids content in slab, in percent (%); F is the load applied onto wheels or roller, in kilonewton (kN); b is the width of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.