SIST EN 12710:2006
Fibreboard drums - Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 l
Fibreboard drums - Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 l
This European Standard specifies the construction requirements for cylindrical fibreboard drums with a nominal capacity of 15 l to 250 l and the preferred range of diameters and capacities.
Fibertrommeln - Deckelfässer mit Spannringen mit einem Nennvolumen von 15 l bis 250 l
Diese Europäische Norm legt die Konstruktionsanforderungen für zylindrische Fibertrommeln im Volumen-bereich
von 15 l bis 250 l mit den vorzuziehenden Durchmessern und Volumen fest.
Futs en carton - Futs a ouverture totale d'une capacité nominale de 15 l a 250 l
La présente Norme européenne spécifie les exigences de construction des futs cylindriques en carton d'une
capacité nominale de 15 l a 250 l ainsi que la gamme de diametres et de capacités a utiliser de préférence.
Sodi iz vlaknenih plošč – Sodi s snemljivim pokrovom (široka odprtina) z zapiralnim obročem z nazivno prostornino od 15 l do 250 l
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Fibreboard drums - Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 lFuts en carton - Futs a ouverture totale d'une capacité nominale de 15 l a 250 lFibertrommeln - Deckelfässer mit Spannringen mit einem Nennvolumen von 15 l bis 250 lTa slovenski standard je istoveten z:EN 12710:2006SIST EN 12710:2006en55.140ICS:SIST EN 12710:20011DGRPHãþDSLOVENSKI
STANDARDSIST EN 12710:200601-september-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12710May 2006ICS 55.140Supersedes EN 12710:1999
English VersionFibreboard drums - Removable head (open head) drums withclosing rings with a nominal capacity of 15 l to 250 lFûts en carton - Fûts à ouverture totale d'une capaciténominale de 15 l à 250 lFibertrommeln - Deckelfässer mit Spannringen mit einemNennvolumen von 15 l bis 250 lThis European Standard was approved by CEN on 28 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12710:2006: E
EN 12710:2005 (E)
2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 Dimensions.6 5 Materials.8 6 Requirements.9 7 Designation.9 Annex A (normative)
Fibreboard drum dimensions.11 Annex B (normative) Fibreboard drum preferred diameter-capacity relationship.12 Annex C (informative) Fitness for use.13 Annex D (informative) Fibreboard drum material identification symbols.14 Bibliography.15
EN 12710:2006 (E) 3 Foreword This document (EN 12710:2006) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. This document supersedes EN 12710:1999 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 12710:2006 (E) 4 Introduction This standard is limited to the specification of constructional details and the establishment of a preferred range of diameters and capacities for fibreboard drums, in recognition of the fact that one of the important characteristics of fibreboard drums is that they can be produced in various ranges of diameters and heights with constructions to suit specific products and market needs and can be fitted with a variety of lids, bases and fasteners.
EN 12710:2006 (E) 5 1 Scope This European Standard specifies the construction requirements for cylindrical fibreboard drums with a nominal capacity of 15 l to 250 l and the preferred range of diameters and capacities. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 2233:2001, Packaging — Complete, filled transport packages and unit loads — Conditioning for testing (ISO 2233:2000) 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1
fibreboard drum rigid, cylindrical container with a sidewall, made of multiple plies of virgin or recycled paper or board firmly bonded together, and a base, firmly connected to the sidewall and a bottom chimb, and a top, which can be removed as a lid and closed by means of the closing ring over the top chimb, the chimb being secured to the sidewall 3.2
nominal capacity (NC) capacity in litres which, by convention, is used to represent a class of drums of similar brimful capacities 3.3
sidewall cylindrical body of the drum
3.4
lid removable top of the drum 3.5
chimb top or bottom rim of the drum 3.6
internal lining fixed inner ply of material, other than that which is used for the general construction of the drum, used to give the drum specific properties 3.7 external lining fixed outer ply of material, other than that which is used for the general construction of the drum, used to give the drum specific properties
EN 12710:2006 (E) 6 3.8 barrier multiple or single ply of material, other than that which is used for the general construction of the drum, incorporated into the sidewall, lid or base of the drum 3.9 liner separate bag or semi-rigid container, used inside the drum to give the drum specific properties 3.10 internal coating material applied to the inner surface of the drum, by spray, brush or other means to give the drum specific properties 3.11 external coating material applied to the outer surface of the drum, by spray, brush or other means to give the drum specific properties 3.12
closing ring band by which a lid can be held to the top of the drum and secured in position by means of a fastening device 3.13 base horizontal bottom wall of the drum 4 Dimensions 4.1 General The drum description shall include the dimensions listed in 4.2 and 4.3.
In addition the description shall include the nominal capacity as determined in 4.4. Drum dimensions are shown in annex A.
4.2 Diameter 4.2.1 Nominal internal diameter The nominal internal diameter is used only to provide a classification of drum diameters. 4.2.2 Internal diameter (d1) The internal diameter (d1), in millimetres, is the internal measurement from the inner sidewall to the diametrically opposite inner sidewall. 4.2.3 Outside diameter (d2) The outside diameter (overall diameter) (d2), in millimetres, is the measurement over the closing ring, but not over the fastening device.
EN 12710:2006 (E) 7 4.3 Height and depth 4.3.1 Internal height (h1) The internal height (h1), in millimetres, is the height from the inner surface of the drum base to the top surface of the top i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.