Rigid plastics containers - Method for determination of drainability

This European standard specifies a method for determination on the drainability of plastics bottles and jars with a normal capacity up to 5.0 l and of plastic canisters/jerricans with a nominal volume up to 20 litres.

Formstabile Kunststoffbehälter - Verfahren zur Bestimmung der Entleerbarkeit

Conteneurs en plastique rigide - Méthode de détermination de l'aptitude au vidage

La présente Norme Européenne spécifie une méthode permettant de déterminer l'aptitude au vidage des bouteilles et des bocaux en plastique d'une capacité nominale inférieure ou égale a 5 l et des bidons et jerricans en plastique d'un volume nominal inférieur ou égal a 20 l.
NOTE   Dans la présente norme, les bouteilles, bocaux, bidons et jerricans en plastique sont désignés par le terme "conteneurs".

Toge plastične posode - Metoda za ugotavljanje odtekanja

General Information

Status
Published
Publication Date
30-Jun-2003
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-2003
Due Date
01-Jul-2003
Completion Date
01-Jul-2003

Buy Standard

Standard
EN 13973:2003
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Formstabile Kunststoffbehälter - Verfahren zur Bestimmung der EntleerbarkeitConteneurs en plastique rigide - Méthode de détermination de l'aptitude au vidageRigid plastics containers - Method for determination of drainability55.140Barrels. Drums. Canisters55.100Steklenice. Lonci. KozarciBottles. Pots. JarsICS:Ta slovenski standard je istoveten z:EN 13973:2002SIST EN 13973:2003en,fr,de01-julij-2003SIST EN 13973:2003SLOVENSKI
STANDARD



SIST EN 13973:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13973October 2002ICS 55.100; 55.140English versionRigid plastics containers - Method for determination ofdrainabilityConteneurs en plastique rigide - Méthode de déterminationde l'aptitude au vidageFormstabile Kunststoffbehälter - Verfahren zur Bestimmungder EntleerbarkeitThis European Standard was approved by CEN on 19 August 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13973:2002 ESIST EN 13973:2003



EN 13973:2002 (E)2ContentspageForeword.3Introduction.41Scope.52Normative references.53Terms and definitions.54Principle.65Sampling.66Apparatus.67Procedure.68Calculation.79Test report.7SIST EN 13973:2003



EN 13973:2002 (E)3ForewordThis document EN 13973:2002 has been prepared by Technical Committee CEN/TC 261 "Packaging", thesecretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by April 2003, and conflicting national standards shall be withdrawn at the latest byApril 2003.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 13973:2003



EN 13973:2002 (E)4Introduction The purpose of packaging is the containment, protection, distribution and promotion of products. A major role isprev
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.