SIST EN 712:1997

Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force

This standard specifies a method for checking the ability of assembled end-load bearing mechanical joints (excluding fusion-welded joints) between fittings and pressure pipes to withstand a longitudinal tensile force.

Thermoplastische Rohrleitungssysteme - Zugfeste mechanische Verbindungen zwischen Druckrohren und Formstücken - Prüfverfahren für den Widerstand gegen Herausziehen unter konstanter Belastung

Diese Norm legt ein Prüfverfahren zur Bestimmung der Widerstandsfähigkeit von zugfesten mechanischen Verbindungen (ausgenommen Schweissverbindungen) zwischen Formstücken und Druckrohren gegenüber axialen Zugbeanspruchungen fest.

Systemes de canalisations thermoplastiques - Assemblages mécaniques avec effet des fonds entre tubes avec pression et raccords - Méthode d'essai de résistance a l'arrachement sous force constante

Cette norme spécifie une méthode d'essai pour la vérification de l'aptitude des assemblages mécaniques avec effet des fonds (a l'exclusion des joints soudés par fusion) entre raccords et tubes avec pression, a supporter une force de traction longitudinale.

Cevni sistemi iz plastomernih materialov - Natezno trdni mehanski spoji med tlačnimi cevmi in fitingi - Metoda za preskus odpornosti na izvlečenje s konstantno osno obremenitvijo

General Information

• Status: Withdrawn
• Publication Date: 31-Jan-1997
• Withdrawal Date: 12-May-2015
• ICS: 23.040.60 - Flanges, couplings and joints
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 12-May-2015
• Due Date: 04-Jun-2015
• Completion Date: 13-May-2015
• Directive: 93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
• Mandate: M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
• Ref Project: EN 712:1993 - Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force

Relations

• Replaced By: SIST EN ISO 3501:2015 - Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2015)
• Effective Date: 01-Jun-2015
• Replaced By: SIST EN ISO 3501:2015 - Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2015)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 712:1997
01-februar-1997
&HYQLVLVWHPLL]SODVWRPHUQLKPDWHULDORY1DWH]QRWUGQLPHKDQVNLVSRMLPHG
WODþQLPLFHYPLLQILWLQJL0HWRGD]DSUHVNXVRGSRUQRVWLQDL]YOHþHQMHVNRQVWDQWQR
RVQRREUHPHQLWYLMR
Thermoplastics piping systems - End-load bearing mechanical joints between pressure
pipes and fittings - Test method for resistance to pull-out under constant longitudinal
force
Thermoplastische Rohrleitungssysteme - Zugfeste mechanische Verbindungen zwischen
Druckrohren und Formstücken - Prüfverfahren für den Widerstand gegen Herausziehen
unter konstanter Belastung
Systemes de canalisations thermoplastiques - Assemblages mécaniques avec effet des
fonds entre tubes avec pression et raccords - Méthode d'essai de résistance a
l'arrachement sous force constante
Ta slovenski standard je is
...