SIST EN ISO 3501:2015

Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2015)

This International Standard specifies a method for checking the ability of assembled uniaxial joints
between fittings and plastic pressure pipes to withstand longitudinal tensile stresses. The test applies
regardless of the design and material of the fitting used for jointing plastics pipe.
This test method is not applicable to fusion-welded joints.

Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Fittings und Druckrohren - Prüfverfahren für den Widerstand gegen Zugbelastung bei konstanter Zugkraft (Ausreißprüfung) (ISO 3501:2015)

Diese Internationale Norm legt ein Verfahren zur Prüfung der Eignung von Montageverbindungen (aus-genommen Schweißverbindungen) zwischen Fittings (Formstücken) und thermoplastischen Druckrohren, axialen Zugbeanspruchungen (Zugspannungen) zu widerstehen, fest. Die Prüfung gilt unabhängig von der konstruktiven Auslegung und dem Werkstoff des Fittings, das für die Verbindung der thermoplastischen Rohe verwendet wird.

Systèmes de canalisations en plastique - Assemblages mécaniques entre raccords et tubes sous pression - Méthode d'essai de résistance à l'arrachement sous une force longitudinale constante (ISO 3501:2015)

L'ISO 3501:2015 spécifie une méthode de vérification de la résistance à la traction longitudinale des assemblages uniaxiaux entre raccords et tubes plastiques sous pression. L'essai s'applique quelles que soient la conception et la matière du raccord utilisé pour le raccordement des tubes plastiques. La méthode d'essai n'est pas applicable aux assemblages soudés par fusion.

Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi cevmi - Metoda za preskus odpornosti proti izvlečenju s konstantno osno obremenitvijo (ISO 3501:2015)

General Information

• Status: Withdrawn
• Public Enquiry End Date: 14-Nov-2013
• Publication Date: 12-May-2015
• Withdrawal Date: 16-Mar-2022
• ICS: 23.040.60 - Flanges, couplings and joints
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 17-Mar-2022
• Due Date: 09-Apr-2022
• Completion Date: 17-Mar-2022
• Directive: 93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
• Mandate: M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
• Ref Project: EN ISO 3501:2015 - Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2015)

Relations

• Replaced By: SIST EN ISO 3501:2022 - Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2021)
• Effective Date: 19-Jan-2022
• Replaces: SIST EN 712:1997 - Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force
• Effective Date: 01-Jun-2015
• Replaces: SIST ISO 3501:1995 - Assembled joints between fittings and polyethylene (PE) pressure pipes -- Test of resistance to pull out
• Effective Date: 04-Jun-2018
• Replaces: SIST EN 712:1997 - Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 3501:2015
01-junij-2015
1DGRPHãþD
SIST EN 712:1997
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY0HKDQVNLVSRMLPHGILWLQJLLQWODþQLPL
FHYPL0HWRGD]DSUHVNXVRGSRUQRVWLSURWLL]YOHþHQMXVNRQVWDQWQRRVQR
REUHPHQLWYLMR,62
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test
method for resistance to pull-out under constant longitudinal force (ISO 3501:2015)
Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Fittings und
Druckrohren - Prüfverfahren für den Widerstand gegen Zugbelastung bei konstanter
Zugkraft (Ausreißprüfung) (ISO 3501:2015)
Systèmes de canalisations en plastique - Assemblages mécaniques entre raccords et
tubes sous pression - Méthode d'essai de résistance à l'arrachement sous une force
longitudinale constante (ISO 3501:2015)
Ta slovenski standard je istoveten z: EN ISO 3501:2015
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
SIST EN ISO 3501:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3501:2015

---------------------- Page: 2 ----------------------

SIST EN ISO 3501:2015

EUROPEAN STANDARD
EN ISO 3501

NORME EUROPÉENNE

EUROPÄISCHE NORM
March 2015
ICS 23.040.60 Supersedes EN 712:1993
English Version
Plastics piping systems - Mechanical joints between fittings and
pressure pipes - Test method for resistance to pull-out under
constant longitudinal force (ISO 3501:2015)
Systèmes de canalisations en plastique - Assemblages Kunststoff-Rohrleitungssysteme - Mechanische
mécaniques entre raccords et tubes sous pression - Verbindungen zwischen Fittings und Druckrohren -
Méthode d'essai de résistance à l'arrachement sous une Prüfverfahren für den Widerstand gegen Zugbelastung bei
force longitudinale constante (ISO 3501:2015) konstanter Zugkraft (Ausreißprüfung) (ISO 3501:2015)
This European Standard was approved by CEN on 7 February 2015.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3501:2015 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3501:2015
EN ISO 3501:2015 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 3501:2015
EN ISO 3501:2015 (E)
Foreword
This document (EN ISO 3501:2015) has been prepared by Technical Committee ISO/TC 138 "Plastics pipes,
fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 712:1993.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 3501:2015 has been approved by CEN as EN ISO 3501:2015 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 3501:2015

---------------------- Page: 6 ----------------------

SIST EN ISO 3501:2015
INTERNATIONAL ISO
STANDARD 3501
Second edition
2015-03-01
Plastics piping systems — Mechanical
joints between fittings and pressure
pipes — Test method for resistance to
pull-out under constant longitudinal
force
Systèmes de canalisations en plastique — Assemblages mécaniques
entre raccords et tubes sous pression — Méthode d’essai de résistance
à l’arrachement sous une force longitudinale constante
Reference number
ISO 3501:2015(E)
©
ISO 2015

---------------------- Page: 7 ----------------------

SIST EN ISO 3501:2015
ISO 3501:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 3501:2015
ISO 3501:2015(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Test parameters and requirements . 1
5 Apparatus . 2
6 Test pieces . 2
7 Procedure. 3
8 Test report . 3
Annex A (normative) Test parameters . 4
© ISO 2015 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 3501:2015
ISO 3501:2015(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1.
...