Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear

This European Standard specifies a method for determining the creep deformation of bonded specimens loaded in bending shear. It is applicable to adhesives used in load bearing timber structures.
It is suitable for the following applications:
a)   for assessing the compliance of adhesives to EN 15425 and EN 16254;
b)   for assessing the suitability and quality of adhesives for load bearing timber structures.
This test is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design, and does not necessarily represent the performance of the bonded member in service.

Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und Aminoplaste - Prüfverfahren - Teil 3: Prüfung der Kriechverformung unter zyklischen Klimabedingungen an Prüfkörpern bei Biege-Scherbeanspruchung

Diese Europäische Norm legt ein Verfahren zur Bestimmung der Kriechverformung an verklebten Prüfkörpern bei Biege-Scherbeanspruchung fest. Sie gilt für Klebstoffe, die für tragende Holzbauteile verwendet werden.
Das Verfahren ist für folgende Anwendungsfälle geeignet:
a)   zur Beurteilung der Übereinstimmung von Klebstoffen mit EN 15425 und EN 16254;
b)   zur Beurteilung der Eignung und Qualität von Klebstoffen für tragende Holzbauteile.
Diese Prüfung ist hauptsächlich dafür vorgesehen, Leistungsdaten für die Klassifizierung von Klebstoffen für tragende Holzbauteile entsprechend ihrer Eignung zur Verwendung in festgelegten klimatischen Umgebungen zu erhalten.
Dieses Verfahren ist nicht dafür vorgesehen, Bemessungswerte bereitzustellen und gibt nicht zwangsläufig die Leistungsfähigkeit des verklebten Bauteils im Gebrauch wieder.

Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste - Méthodes d'essais - Partie 3 : Essai de déformation par fluage dans des conditions climatiques cycliques avec des éprouvettes chargées en cisaillement par flexion

La présente Norme européenne spécifie une méthode permettant de déterminer la déformation par fluage d’éprouvettes collées chargées en cisaillement par flexion. Elle s’applique aux adhésifs utilisés dans des structures portantes en bois.
Elle est adaptée :
a)   pour évaluer la conformité des adhésifs à l’EN 15425 et à l'EN 16254 ;
b)   pour évaluer l’aptitude à l’utilisation et la qualité des adhésifs pour les structures portantes en bois.
Cet essai est principalement destiné à recueillir des données de performance pour classer les adhésifs destinés aux structures portantes en bois en fonction de leur aptitude à l’utilisation dans des environnements climatiques définis.
Cette méthode n’est pas destinée à fournir des données pour la conception structurelle et elle ne reflète pas nécessairement la performance de l’élément collé en service.

Lepila (razen fenolnih ali aminskih) za nosilne lesene konstrukcije - Preskusne metode - 3. del: Preskus deformacij lezenja v cikličnih klimatskih pogojih s preskušanci pod upogibno-strižno obremenitvijo

Ta evropski standard določa metodo za ugotavljanje deformacije lezenja zlepljenih preskušancev pod upogibno strižno obremenitvijo. Uporablja se za lepila za nosilne lesene konstrukcije.
Metoda se uporablja:
a) za oceno skladnosti lepil s standardoma EN 15425 in EN 16254;
b) za oceno ustreznosti in kakovosti lepil za nosilne lesene konstrukcije.
Ta preskus je namenjen zlasti za pridobivanje podatkov o lastnostih za razvrstitev lepil za nosilne lesene konstrukcije glede na njihovo ustreznost za uporabo v opredeljenih podnebnih okoljih.
Ta metoda ni namenjena za zagotavljanje podatkov za konstrukcijsko zasnovo, pri čemer ne predstavlja nujno lastnosti zlepljenega elementa v uporabi.

General Information

Status
Published
Publication Date
07-Apr-2019
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Apr-2019
Due Date
10-Jun-2019
Completion Date
08-Apr-2019

Relations

Buy Standard

Standard
EN 15416-3:2017+A1:2019
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 15416-3:2017+A1:2019
01-junij-2019
/HSLOD UD]HQIHQROQLKDOLDPLQVNLK ]DQRVLOQHOHVHQHNRQVWUXNFLMH3UHVNXVQH
PHWRGHGHO3UHVNXVGHIRUPDFLMOH]HQMDYFLNOLþQLKNOLPDWVNLKSRJRMLKV
SUHVNXãDQFLSRGXSRJLEQRVWULåQRREUHPHQLWYLMR
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test
methods - Part 3: Creep deformation test at cyclic climate conditions with specimens
loaded in bending shear
Klebstoffe für tragende Holzbauteile ausgenommen Phenolharzklebstoffe und
Aminoplaste - Prüfverfahren - Teil 3: Prüfung der Kriechverformung unter zyklischen
Klimabedingungen an Prüfkörpern bei Biege-Scherbeanspruchung
Adhésifs pour structures portantes en bois de type autre que phénolique et aminoplaste -
Méthodes d'essais - Partie 3 : Essai de déformation par fluage dans des conditions
climatiques cycliques avec des éprouvettes chargées en cisaillement par flexion
Ta slovenski standard je istoveten z: EN 15416-3:2017+A1:2019
ICS:
83.180 Lepila Adhesives
91.080.20 Lesene konstrukcije Timber structures
SIST EN 15416-3:2017+A1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 15416-3:2017+A1:2019

---------------------- Page: 2 ----------------------

SIST EN 15416-3:2017+A1:2019


EN 15416-3:2017+A1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2019
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN 15416-3:2017
English Version

Adhesives for load bearing timber structures other than
phenolic and aminoplastic - Test methods - Part 3: Creep
deformation test at cyclic climate conditions with
specimens loaded in bending shear
Adhésifs pour structures portantes en bois de type Klebstoffe für tragende Holzbauteile ausgenommen
autre que phénolique et aminoplaste - Méthodes Phenolharzklebstoffe und Aminoplaste - Prüfverfahren
d'essais - Partie 3 : Essai de déformation par fluage - Teil 3: Prüfung der Kriechverformung unter
dans des conditions climatiques cycliques avec des zyklischen Klimabedingungen an Prüfkörpern bei
éprouvettes chargées en cisaillement par flexion Biege-Scherbeanspruchung
This European Standard was approved by CEN on 30 October 2016 and includes Amendment 1 approved by CEN on 9 February
2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15416-3:2017+A1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 15416-3:2017+A1:2019
EN 15416-3:2017+A1:2019 (E)
Contents Page
European foreword . 3
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Principle . 7
5 Apparatus . 7
5.1 Test jig . 7
5.2 Climate chamber. 8
5.3 Measuring gauge . 8
6 Preparation of specimens . 8
6.1 General . 8
6.2 Option 1 . 8
6.3 Option 2 . 9
7 Test procedure, evaluation and expression of results . 10
7.1 Test procedure . 10
7.2 Evaluation and expression of results . 11
8 Test report . 12

2

---------------------- Page: 4 ----------------------

SIST EN 15416-3:2017+A1:2019
EN 15416-3:2017+A1:2019 (E)
European foreword
This document (EN 15416-3:2017+A1:2019) has been prepared by Technical Committee CEN/TC 193
“Adhesives”, the secretariat of which is held by AENOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2019, and conflicting national standards
shall be withdrawn at the latest by September 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document includes Amendment 1 approved by CEN on 9 February 2019.
This document supersedes !EN 15416-3:2017".
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
Compared to EN 15416-3:2007+A1:2010, the following main modifications have been made:
a) reference to EN 16254 for EPI adhesives added in the scope;
b) glue line thickness to be used will be taken from EN 15425 or EN 16254;
c) alternative way of making the test pieces is given in 6.2 and 6.3;
d) possibility to use other climatic conditions as given in 7.1, Table 1 has been deleted;
e) loads have been given a tolerance of ± 50 N in 7.1;
f) duration times can be found in EN 15425 or in EN 16254;
g) measurement of the glue line thickness in the test piece has been introduced.
This document is one of a series dealing with adhesives for use with timber structures, and is published
in support of product standards for bonded load-bearing timber structures.
The series consists of three classification and performance requirements for adhesives for load-bearing
timber structures, phenolic and aminoplastic adhesives (EN 301), one component polyurethane
adhesives (EN 15425) and emulsion polymerized isocyanate adhesives (EN 16254), together with 12
test methods (EN 302 Parts 1 to 8 and EN 15416 Parts 1 and 3 to 5).
These European Standards have the following titles:
— EN 301, Adhesives, phenolic and aminoplastic, for load-bearing timber structures — Classification and
performance requirements
— EN 15425, Adhesives — One component polyurethane (PUR) for load-bearing timber structures —
Classification and performance requirements
— EN 16254, Adhesives — Emulsion polymerized isocyanate (EPI) for load-bearing timber structures —
Classification and performance requirements
3

---------------------- Page: 5 ----------------------

SIST EN 15416-3:2017+A1:2019
EN 15416-3:2017+A1:2019 (E)
— EN 302-1, Adhesives for load-bearing timber structures —Test methods — Part 1: Determination of
longitudinal tensile shear strength
— EN 302-2, Adhesives for load-bearing timber structures —Test methods — Part 2: Determination of
resistance to delamination
— EN 302-3, Adhesives for load-bearing timber structures — Test methods — Part 3: Determination of
the effect of acid damage to wood fibres by temperature and humidity cycling on the transverse tensile
strength
— EN 302-4, Adhesives for load-bearing timber structures — Test methods — Part 4: Determination of
the effects of wood shrinkage on the shear strength
— EN 302-5, Adhesives for load-bearing timber structures — Test methods — Part 5: Determination of
maximum assembly time under referenced conditions
— EN 302-6, Adhesives for load-bearing timber structures — Test methods — Part 6: Determination of
the minimum pressing time under referenced conditions
— EN 302-7, Adhesives for load-bearing timber structures — Test methods — Part 7: Determination of
the working life under referenced conditions
— EN 302-8, Adhesives for load-bearing timber structures — Test methods — Part 8: Static load test of
multiple bond line specimens in compression shear
— EN 15416-1, Adhesives for load bearing timber structures other than phenolic and aminoplastic —
Test methods — Part 1: Long-term tension load test perpendicular to the bond line at varying climate
conditions with specimens perpendicular to the glue line (Glass house test)
— EN 15416-3, Adhesives for load bearing timber structures other than phenolic and aminoplastic —
Test methods — Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in
bending shear
— EN 15416-4, Adhesives for load bearing timber structures other than phenolic and aminoplastic —
Test methods — Part 4: Determination of open assembly time under referenced conditions
— EN 15416-5, Adhesives for load bearing timber structures other than phenolic and aminoplastic —
Test methods — Part 5: Determination of minimum pressing time under referenced conditions
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
4

---------------------- Page: 6 ----------------------

SIST EN 15416-3:2017+A1:2019
EN 15416-3:2017+A1:2019 (E)
Introduction
Safety statement
Persons using this European Standard should be familiar with the normal laboratory practice, if
applicable. This European Standard cannot address all of the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure
compliance with any regulatory conditions.
Environmental statement
It is understood that some of the material permitted in this European Standard may have negative
environmental impact. As technological advantages lead to better alternatives for these materials, they
will be eliminated from this European Standard to the extent possible.
At the end of the test, it is recommended that the user of this European Standard take care to carry out
an appropriate disposal of the wastes, according to local regulation.
5

---------------------- Page: 7 ----------------------

SIST EN 15416-3:2017+A1:2019
EN 15416-3:2017+A1:2019 (E)
1 Scope
This European Standard specifies a method for determining the creep deformation of bonded
specimens loaded in bending shear. It is applicable to adhesives used in load bearing timber structures.
It is suitable for the following applications:
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.