kSIST FprEN ISO 18314-4:2023
(Main)Analytical colorimetry - Part 4: Metamerism index for pairs of samples for change of illuminant (ISO/FDIS 18314-4:2023)
Analytical colorimetry - Part 4: Metamerism index for pairs of samples for change of illuminant (ISO/FDIS 18314-4:2023)
This document specifies a formalism for the calculation of the illuminant metamerism of solid surface colours. It cannot be applied to colours of effect coatings without metrical adaptation.
This document only covers the phenomenon of metamerism for change of illuminant, which has the greatest meaning in practical application. In the case of chromaticity coordinates of a pair of samples under reference conditions that do not exactly match, recommendations are given on which correction measures are to be taken. Regarding the reproduction of colours, the metamerism index is used as a measure of quality in order to specify tolerances for colour differences between a colour sample and a colour match under different illumination conditions.
The quantification of the illuminant metamerism of pairs of samples is formally performed by a colour difference assessment, for which tolerances that are common for the evaluation of residual colour differences can be used.
NOTE In the colorimetric literature and textbooks, the term geometric metamerism is sometimes used for the case that two colours appear to be the same under a specific geometry for visual assessment and selected standard observer and standard illuminant pair, but is perceived as two different colours at changed observation geometry. The term geometric metamerism is different to metamerism described in this document.
Analytische Farbmessung - Teil 4: Metamerie-Index von Probenpaaren bei Lichtartwechsel (ISO/FDIS 18314-4:2023)
Dieses Dokument legt einen Formalismus zur Berechnung der Lichtart-Metamerie von Uni-Farben fest. Dieser kann ohne Anpassungen in der Metrik nicht auf Effektfarben von Überzügen bzw. Beschichtungen angewendet werden.
Dieses Dokument behandelt nur das Phänomen der Metamerie bei Lichtartwechsel, das in der praktischen Anwendung die größte Bedeutung hat. Für die Fälle, in denen die Farborte eines Probenpaares unter Referenz¬bedingungen nicht exakt übereinstimmen, enthält dieses Dokument Leitlinien für die zu ergreifenden Korrekturmaßnahmen. Bei der Reproduktion von Farben wird der Metamerie-Index als Qualitätsmaß verwendet, um Toleranzen für Farbunterschiede zwischen einer Farbvorlage und einer Farbnachstellung bei unterschiedlichen Beleuchtungsbedingungen festzulegen.
Die Quantifizierung der Lichtart-Metamerie von Probenpaaren wird formal auf eine Farbabstandsbewertung zurückgeführt, bei der Toleranzen herangezogen werden können, die bei der Bewertung reiner Restfarb¬abstände üblich sind.
ANMERKUNG In der Farbliteratur und Fachbüchern wird manchmal auch der Begriff der Geometrischen Metamerie für den Fall verwendet, in dem zwei Farben unter einer bestimmten Beobachtungsgeometrie und einer gewählten Kombination aus Normalbeobachter und Lichtart gleich erscheinen, aber bei veränderter Beobachtungsgeometrie als zwei verschiedene Farben wahrgenommen werden. Der Begriff Geometrische Metamerie unterscheidet sich von der in diesem Dokument beschriebenen Metamerie.
Analyse colorimétrique - Partie 4: Indice de métamérisme de paires d'échantillons pour changement d'illuminant (ISO/FDIS 18314-4:2023)
Le présent document spécifie un formalisme pour le calcul du métamérisme de l’illuminant de couleurs de surfaces solides. Il ne s’applique pas à des couleurs de revêtements à effets sans adaptation métrique.
Le présent document ne couvre que le phénomène de métamérisme pour changement d’illuminant, qui a la plus grande signification dans l’application pratique. Dans le cas de coordonnées de chromaticité d’une paire d’échantillons dans des conditions de référence qui ne correspondent pas exactement, des recommandations sont données sur les mesures de correction à prendre. En ce qui concerne la reproduction de couleurs, l’indice de métamérisme est utilisé comme mesure de qualité, de manière à spécifier des tolérances pour les écarts de couleurs entre un échantillon de couleurs et un appariement des couleurs dans différentes conditions d’éclairage.
La quantification du métamérisme de l’illuminant de paires d’échantillons est formellement réalisée par une évaluation de l’écart de couleurs, pour laquelle des tolérances communes à l'évaluation d’écarts résiduels de couleurs peuvent être utilisées.
NOTE Dans la littérature et les manuels relatifs à la colorimétrie, le terme métamérisme géométrique est parfois utilisé dans le cas où deux couleurs semblent être identiques sous une géométrie spécifique pour l’évaluation visuelle et l’observateur de référence sélectionné et la paire d’illuminants normalisés, mais sont perçues comme deux couleurs différentes lorsque la géométrie d’observation est changée. Le terme métamérisme géométrique est différent du métamérisme décrit dans le présent document.
Analizna kolorimetrija - 4. del: Metamerični indeks parov vzorcev pri spremembi vrste svetila (ISO/FDIS 18314-4:2023)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 18314-4:2023
01-marec-2023
Analizna kolorimetrija - 4. del: Metamerični indeks parov vzorcev pri spremembi
vrste svetila (ISO/DIS 18314-4:2023)
Analytical colorimetry - Part 4: Metamerism index for pairs of samples for change of
illuminant (ISO/DIS 18314-4:2023)
Analytische Farbmessung - Teil 4: Metamerie-Index von Probenpaaren bei
Lichtartwechsel (ISO/DIS 18314-4:2023)
Analyse colorimétrique - Partie 4: Indice de métamérisme de paires d'échantillons pour
changement d'illuminant (ISO/DIS 18314-4:2023)
Ta slovenski standard je istoveten z: prEN ISO 18314-4
ICS:
17.180.20 Barve in merjenje svetlobe Colours and measurement of
light
87.060.10 Pigmenti in polnila Pigments and extenders
oSIST prEN ISO 18314-4:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 18314-4:2023
---------------------- Page: 2 ----------------------
oSIST prEN ISO 18314-4:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18314-4
ISO/TC 256 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-01-06 2023-03-31
Analytical colorimetry —
Part 4:
Metamerism index for pairs of samples for change of
illuminant
Analyse colorimétrique —
Partie 4: Indice de métamérisme de paires d'échantillons pour changement d'illuminant
ICS: 87.060.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 18314-4:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 3 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18314-4
ISO/TC 256 Secretariat: DIN
Voting begins on: Voting terminates on:
Analytical colorimetry —
Part 4:
Metamerism index for pairs of samples for change of
illuminant
Analyse colorimétrique —
Partie 4: Indice de métamérisme de paires d'échantillons pour changement d'illuminant
ICS: 87.060.10
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 18314-4:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
© ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 4 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms.2
5 Reference illuminant .3
6 Test illuminant . 3
7 CIELAB coordinates L*, a*, b* . 3
8 Metamerism index for change in illuminant . 4
8.1 General calculation methods . 4
8.2 Basic calculation of the metamerism index from colour differences . 5
8.3 Correction methods . 5
8.3.1 Additive correction . 5
8.3.2 Multiplicative correction . 6
8.3.3 Spectral correction. 6
8.4 Test report . 10
Annex A (informative) Calculation examples .11
Bibliography .23
iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 256, Pigments, dyestuff and extenders.
This second edition cancels and replaces the first edition (ISO 18314-4:2020), which has been
technically revised.
The main changes are as follows:
— a brief introduction about differentiation between metamerism and paramerism has been added in
8.1;
— for consistency reasons with old formulas 2 and 4 and 24, the old formula 1 has been updated;
— the key of Figure A.1 has been updated;
— the document has been editorially revised.
A list of all parts in the ISO 18314 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
Introduction
For the phenomenon of metamerism of pairs of samples, three different kinds are distinguished:
a) Illuminant metamerism occurs if both of the object colours of a pair of samples are perceived as
being the same only under a specific illuminant (e.g. under illuminant D65), while they differ under
a different illuminant (e.g. illuminant A).
b) Observer metamerism occurs if the object colours of a pair of samples are perceived as being the
same by one observer, while a different observer perceives a colour difference under the same
illuminant and the same reference conditions.
NOTE 1 The observer metamerism is caused by differences between the distributions of spectral colour
matching functions of different observers.
c) Field-size metamerism occurs if both of the object colours of a pair of samples are perceived as
being the same on the retina for a size of an observation field (e.g. defined by the 2° standard
observer), while they differ for a different observation field on the retina (e.g. 10°).
NOTE 2 The reason for field-size metamerism is based on the existent colour matching functions of
an observer during an observation situation. The colour matching functions change with the size of the
observation field on the retina. Such change of the observation field can also occur if, for example, the pair of
samples is examined from different distances.
v
© ISO 2022 – All rights reserved
---------------------- Page: 7 ----------------------
oSIST prEN ISO 18314-4:2023
---------------------- Page: 8 ----------------------
oSIST prEN ISO 18314-4:2023
DRAFT INTERNATIONAL STANDARD ISO/DIS 18314-4:2022(E)
Analytical colorimetry —
Part 4:
Metamerism index for pairs of samples for change of
illuminant
1 Scope
This document specifies a formalism for the calculation of the illuminant metamerism of solid surface
colours. It cannot be applied to colours of effect coatings without metrical adaptation.
This document only covers the phenomenon of metamerism for change of illuminant, which has the
greatest meaning in practical application. In the case of chromaticity coordinates of a pair of samples
under reference conditions that do not exactly match, recommendations are given on which correction
measures are to be taken. Regarding the reproduction of colours, the metamerism index is used as a
measure of quality in order to specify tolerances for colour differences between a colour sample and a
colour match under different illumination conditions.
The quantification of the illuminant metamerism of pairs of samples is formally performed by a colour
difference assessment, for which tolerances that are common for the evaluation of residual colour
differences can be used.
NOTE In the colorimetric literature and textbooks, the term geometric metamerism is sometimes used for
the case that two colours appear to be the same under a specific geometry for visual assessment and selected
standard observer and standard illuminant pair, but is perceived as two different colours at changed observation
geometry. The term geometric metamerism is different to metamerism described in this document.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/CIE 11664-1, Colorimetry — Part 1: CIE standard colorimetric observers
1)
ISO/CIE 11664-2:—, Colorimetry — Part 2: CIE standard illuminants
ISO/CIE 11664-4, Colorimetry — Part 4: CIE 1976 L*a*b* colour space
CIE 015, Colorimetry
CIE S 017, International Lighting Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in CIE S 017 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
1) Under preparation. Stage at the time of preparation: ISO/CIE DIS 11664-2:2020.
1
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
3.1
metamerism
property of spectrally different colour stimuli that have the same tristimulus values in a specified
colorimetric system
[SOURCE: CIE 017:2016, 17-23-006]
3.2
paramerism
characteristic of a pair of samples with spectral colour stimulus functions which have different
fundamental colour stimulus functions as well as different residuals or metameric black values within
the visible spectral range
Note 1 to entry: Parameric objects are characterized by the fact that they reflect colour stimuli of different
spectral power distribution functions under a specified standard illuminant, which cause approximately the
same colour perception under the selected observation conditions.
3.3
colour difference
*
ΔE
difference between two colour stimuli, defined as a distance between the points representing them in a
specified colour space
*
[SOURCE: CIE 017:2016, 17-22-041, modified — symbol ΔE was amended, “Euclidean” and Note 1 to
entry have been deleted.]
3.4
reference illuminant
illuminant with which other illuminants are compared
[SOURCE: CIE S 017:2016, 17-22-109 17]
3.5
test illuminant
illuminant, for which the colour difference (3.3) between the two samples to be tested is assessed
3.6
metamerism-index for change in illuminant
M
t
* *
colour difference ΔE (3.3) between the two samples under test illuminant (3.5) if Δ=E 0 is observed
under the reference illuminant (3.4)
3.7
correction method
algorithm for theoretically eliminating a colour difference (3.3) of the pair of samples under the reference
illuminant (3.4)
4 Symbols and abbreviated terms
For the application of this document, the symbols given in Table 1 apply.
Table 1 — Symbols
Symbol Identification
X, Y, Z Standard tristimulus values of a measured object colour
Standard tristimulus values of the used illuminant
X , Y , Z
n n n
x , y , z
Colour-matching functions
2
© ISO 2022 – All rights reserved
---------------------- Page: 10 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
TTabablele 1 1 ((ccoonnttiinnueuedd))
Symbol Identification
* * * Basic coordinates of the CIELAB system
L , a , b
ΔL*, Δa*, Δb* Differences between basic coordinates of the CIELAB system
Metamerism index for change in illuminant
M
t
Vector of the radiometric function of a sample with associated fundamental colour stimulus (f)
NN,,N
fr
and metameric black (r)
λ Wavelength
S Relative spectral distribution function of an illuminant
Vector of the standard tristimulus values
W
w Integration weights for the calculation of the standard tristimulus values
A Matrix of the integration weights w for the calculation of the standard tristimulus values
R Projection matrix
I Identity matrix
Index spl Sample
Index std Standard
Index t Test illuminant
Index corr Corrected value
Index f Fundamental colour stimulus
Index r Metameric black values (residuals)
Index ref Reference illuminant
Index T Transposed matrix
5 Reference illuminant
The standard illuminant D65 is chosen as reference illuminant in accordance with ISO/CIE 11664-2.
Other reference illuminants required in special cases shall be particularly specified.
6 Test illuminant
The selection of the test illuminant depends on the application. If the test illuminants are not particularly
specified, standard illuminant A in accordance with ISO 11664-2 and/or illuminants of the fluorescent
lamp type, such as FL11 in accordance with CIE 015, shall preferably be selected. The test illuminant
used shall be indicated as an index to M, e.g. M or M .
A FL11
When calculating the standard tristimulus values X, Y, Z under the selected test illuminants, the basic
raster of wavelengths given in ISO 11664-2 or CIE 015 for A and D65, and in CIE 015 for FL11 and
FL2 shall be complied with. In cases of missing measuring values of the standard or sample for these
wavelengths, these values shall be interpolated and/or extrapolated.
7 CIELAB coordinates L*, a*, b*
* * *
The metamerism index M is based on the CIELAB coordinates L , a , b of samples 1 and 2 which are
t
* * *
to be compared. L , a , b is calculated in accordance with ISO/CIE 11664-4 from the standard
tristimulus values X, Y, Z of the sample for the CIE 1964 10° standard observer in accordance with
* * *
ISO/CIE 11664-1 for the reference illuminant and the selected test illuminant. If calculating L , a , b
under the test illuminant, the respective standard tristimulus values X , Y , Z of the entirely matt
n n n
white surface shall be used (see CIE 015). For the standard illuminants A and D65 or for the illuminant
3
© ISO 2022 – All rights reserved
---------------------- Page: 11 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
recommendation FL11, the standard tristimulus values X , Y , Z of the entirely matt white surface
n n n
apply in accordance with Table 2.
Table 2 specifies standard tristimulus values for the frequently used standard illuminants D65 and A as
well as illuminant FL11 and both of the standard observers in accordance with CIE 015.
Table 2 — Standard tristimulus values
2° standard observer 10° standard observer
Standard
tristimulus Illuminant
values
D65 A FL11 D65 A FL11
X 95,04 109,85 100,96 94,81 111,14 103,86
n
Y 100,00 100,00 100,00 100,00 100,00 100,00
n
Z 108,88 35,58 64,35 107,32 35,20 65,61
n
For fluorescent samples, the illuminant used for measurement shall be adjusted as close as possible to
that illuminant for which the standard tristimulus values are to be determined.
NOTE In contrast to non-fluorescent samples, the calculation of metamerism indices for fluorescent samples
is erroneous if the samples are measured only under one illuminant.
8 Metamerism index for change in illuminant
8.1 General calculation methods
According to 3.1, metamerism implies no colour difference under reference illuminant. The colour
difference under test illuminant is used as metamerism index. This index is descripted in Formula (1):
22 2
** *
ML=Δ +Δab+Δ (1)
() () ()
tt tt
where
t is the test colour;
* * *
ΔL =−LL ;
t splc,,orrt stdt,
* * *
Δa =−aa ;
t splc,,orrt stdt,
* * *
Δb =−bb .
t splc,,orrt stdt,
In case of a small colour difference already present under reference illuminant conditions, the colour
difference at change of illuminant is called paramerism. To eliminate the effect of the difference under
reference illuminant a mathematically corrected virtual sample is created having no remaining colour
difference under the reference illuminant
Three different correction methods for calculating a metamerism index in the case of paramerism have
been proposed in References [6] to.[13] All methods assume that, for practical cases, there might be
already a small difference between the colours of the sample and the standard even under the reference
illuminant from the very beginning, due to problems of fabrication. In the case of two methods, called
the additive and the multiplicative correction, these inherent colour differences often merge with the
difference introduced by the change of the illuminant. The third method, the spectral correction, works
4
© ISO 2022 – All rights reserved
---------------------- Page: 12 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
more fundamentally by the separation of inherent colour differences under the reference illuminant
from those introduced by the change of the illuminant.
NOTE Annex A includes calculation examples.
8.2 Basic calculation of the metamerism index from colour differences
After this correction (see 8.1) leading to the virtual sample, the common formula for a metamerism
index at change in illuminant, expressed in CIELAB coordinates for the test illuminant (t), is given by
Formula (2):
22 2
** *
ML()x =Δ +Δab+Δ (2)
() () ()
tcorrcorrcorr
where
t is the test colour;
* * *
ΔL =−LL ;
corr splc,,orrt stdt,
* * *
Δa =−aa ;
corr splc,,orrt stdt,
* * *
Δb =−bb ;
corr splc,,orrt stdt,
x nominates the correction method.
The formulae given above are meant as an example if using the CIELAB colour space.
Analogous equations apply for other Euclidian colour spaces such as DIN 99o in DIN 6176. In non-
Euclidian colour spaces such as CIE 94 or CIEDE2000, the specific colour differences are provided
with colour-space dependent weight functions and, in regard to the latter case, are expanded by an
additional rotation term. The CIELAB metric used in the present standard is an example and should be
replaced in practical applications by one of the mentioned more recent metrics (e.g. CIE 94, CIEDE2000,
DIN 99o), which are significantly more uniform than the CIELAB model.
8.3 Correction methods
8.3.1 Additive correction
When using the additive correction, the differences of any colorimetric axis between standard (std)
and sample (spl) under reference conditions (ref), are added to the specific differences between
standard and sample under test conditions (t). The resulting equation for the metamerism index M ,
t
expressed in CIELAB coordinates, is then given by Formula (3):
22 2
** *
ML()add =Δ +Δab+Δ (3)
() () ()
t corr corr corr
where
* * **
ΔL = LL−−ΔL ;
corr splt, stdt, ref
* * *
ΔL = LL− .
ref splr, ef stdr, ef
* *
Analogous relationships apply for Δa and Δb . It should be noted that slightly different results are to
be expected, if the correction is applied to standard tristimulus values prior to transformation into a
uniform colour space such as CIELAB or DIN 99o.
5
© ISO 2022 – All rights reserved
---------------------- Page: 13 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
8.3.2 Multiplicative correction
When using the multiplicative correction, which is specified in CIE 015 as correction method, the
standard tristimulus values of the sample (spl), which are observed under test conditions (t) are
multiplied with the quotient of the standard tristimulus values of standard (std) and sample (spl),
which are obtained under reference conditions (ref). The resulting equation is given in Formula (4):
Y
stdr, ef
YY= (4)
spl,corr,tspl,t
Y
splr, ef
in which case, again, analogous combinations for X and Z apply. Subsequently, a transformation
corr corr
into a uniform colour space (e.g. CIELAB) takes place and results in Formula (5):
22 2
** *
ML()multipl =Δ +Δab+Δ (5)
() () ()
t corr corr corr
with
* * *
Δ=LL − L
corr splc,,orrt stdt,
* *
Analogous relationships apply for the two remaining specific differences Δa and Δb .
corr corr
8.3.3 Spectral correction
The spectral method considers that under the reference illuminant, minor differences between the
tristimulus values of the sample and the standard can already exist, which are not relevant for the
metamerism characteristics. In order to first mathematically compensate them and only determine
the effective component for metamerism at change in illuminant of sample pairs with given spectral
reflectance, the possibility is used to mathematically split a spectral reflectance in two additive
components.
One component describes only the function that is effective for the formation of the colour stimulus
under the reference illuminant and the other component describes a function, which does not lead to a
contribution to the colour stimulus when integrating via the stimulus under the reference illuminant.
This function necessarily includes positive and negative components. The colour stimulus function
resulting from the first component of the spectral reflectance under the reference illuminant that is
effective for the formation of the colour stimulus is called fundamental colour stimulus function, the
respective second part of the colour stimulus function leads to a metameric black of the decomposition
(residue), i.e. an invisible contribution with a resulting colour stimulus identical to zero.
The compensation of the deviations of the colour stimuli of a sample from the standard, which are non-
effective for metamerism characteristics, is realized by replacing the fundamental colour stimulus of
the sample by that of the standard. The component that is effective for the metamerism characteristic
is maintained unchanged, i.e. a new colour stimulus function of the sample is generated from the sum
of the replaced fundamental colour stimulus and the unchanged second component. From the sum, the
metamerism at change in illuminant in regard to the standard is determined.
The following mathematical description of the method of spectral correction is not based on a
decomposition of the colour stimulus function into its fundamental colour stimulus function and the
invisible function of the black stimulus. Rather, a decomposition of the spectral reflectance function of
the respective colour into a “fundamental reflectance function” and a “black” component (metameric
black values) of the reflectance function is used. This method is valid under the assumption that these
components only lead to the visually effective fundamental colour stimulus function and the invisible
function of the metameric black values in combination with the distribution function of the reference
illuminant (here D65). Consequently, the distribution function of the reference illuminant is inherently
included in the decomposition of the reflectance functions. In order to highlight this connection, the
6
© ISO 2022 – All rights reserved
---------------------- Page: 14 ----------------------
oSIST prEN ISO 18314-4:2023
ISO/DIS 18314-4:2022(E)
components are additionally marked “for the reference illuminant” when decomposing the reflectance
function of a colour.
In the model of the spectral decomposition of a radiometric function developed by Cohen and Kappauf,
the spectral reflectance of an object colour obtained in the visible spectral range is summarized in the
vector in Formula (6):
ρλ
()
1
ρλ()
2
N = (6)
ρλ
()
n
The components of the vector Nare the reflectance values ρλ in=…12,, , of the examined colour,
() ()
i
which are discreetly present on n intervals. For the calculation of the respective standard tristimulus
values XY,,Z from the reflectance functions, the product based on the supporting points of the
distribution function of the used illuminant S()λ , the respective standard colour-matching function
[see Formula (7)]
αλ()={}xy()λλ,,() z()λ (7)
ii ii
the distance of supporting points Δλ and a normalization constant k shall be determined.
The components ρλ() of the vector N are the reflectances of the examined colour. Considering the
i
illuminant S()λ , the st
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.