iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1762:2000

(Main)

Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification

Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification

This European Standard specifies the requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in liquid or gaseous phase and natural gas with a maximum working pressure of -30°C to +70°C and, when designated -LT, -50°C to +70°C.

Gummischläuche und -schlauchleitungen für Flüssiggas LPG (flüssig oder gasförmig) und Erdgas bis 25 bar (2,5 MPa) - Spezifikation

Diese Europäische Norm legt Anforderungen für Gummischläuche und -schlauchleitungen fest, die zur Übergabe von Flüssiggas LPG (in der flüssigen oder gasförmigen Phase) sowie Erdgas bei Drücken bis zu maximal 25 bar (2,5 MPa) oder Vakuum innerhalb eines Temperaturbereichs von -30°C bis +70°C oder -50°C bis +70°C (Typ LT) verwendet werden.

Tuyaux et flexibles en caoutchouc pour le gaz de pétrole liquéfié GPL (en phase liquide ou gazeuse) et le gaz naturel jusqu'a 25 bar (2,5 MPa) - Spécification

La présente norme européenne spécifie les prescriptions relatives aux tuyaux et flexibles en caoutchouc destinés au transport du gaz de pétrole liquéfié (G.P.L.) en phase liquide ou gazeuse et du gaz nturel sous une pression maximale de service de 25 bar (2,5 MPa) et sous vide dans la plage de température de -30°C a +70°C et -50°C a +70°C pour le type L.T.

Gumene cevi in cevni priključki za utekočinjeni propan/butan (tekoča ali plinska faza) in zemeljski plin do 25 barov (2,5 MPa) - Specifikacija

General Information

Status
Withdrawn
Publication Date
30-Nov-2000
Withdrawal Date
31-Dec-2003
ICS
75.200 - Petroleum products and natural gas handling equipment
83.140.40 - Hoses
Technical Committee
IPMA - Polimer materials and products
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Jan-2004
Due Date
01-Jan-2004
Completion Date
01-Jan-2004
Directive
89/106/EEC - Construction products
Ref Project
EN 1762:1997 - Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification

Relations

Replaced By
SIST EN 1762:2004 - Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification
Effective Date
01-Jan-2004

Buy Standard

EN 1762:2000EN 1762:2000
PreviousNext
Standard
EN 1762:2000
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gummischläuche und -schlauchleitungen für Flüssiggas LPG (flüssig oder gasförmig) und Erdgas bis 25 bar (2,5 MPa) - SpezifikationTuyaux et flexibles en caoutchouc pour le gaz de pétrole liquéfié GPL (en phase liquide ou gazeuse) et le gaz naturel jusqu'a 25 bar (2,5 MPa) - SpécificationRubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Spe
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 13483:2022(Main)
Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
EN 13483:2022

This document specifies the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.
The hose assemblies with vapour recovery for delivery systems on petrol filling stations need to be capable of withstanding anticipated mechanical, thermal and chemical stressing and be resistant to the combustible liquids used in these applications as well as their vapour and vapour air mixtures. It is imperative that the assemblies be constructed in such a way that actions during normal operation cannot give rise to dangerous electrostatic charges nor that there will be any reduction in the performance of the vapour recovery.
The assemblies are intended for use at ambient temperatures between –30 °C and +55 °C for normal temperature class and –40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar .
Hoses can be constructed from rubber or thermoplastic elastomer (TPE) and this document specifies the requirements for three types of hoses in two grades and two classes of hose assemblies for measured fuel dispensing systems, including oxygenated fuels (≤15 % oxygenated compounds) with internal vapour recovery tubing or hose.
NOTE   This document is not applicable to multi chamber fuel dispensing hoses.
As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 are carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1762:2019(Main)
Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification
EN 1762:2018

This European Standard specifies the requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in liquid or gaseous phase and natural gas with a maximum working pressure of 25 bar (2,5 MPa) and vacuum within the temperature range of −30 °C to +70 °C and, when designated -LT, −50 °C to +70 °C.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1765:2016(Main)
Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies
EN 1765:2016

This draft European Standard specifies the characteristics of four types of oil suction and discharge hose assemblies used for the conveyance of petroleum, including crude oils and other liquid petroleum products containing a maximum aromatics content of 50 % (v/v). It is not suitable for liquefied petroleum gas and natural gas.
Hose assemblies to this document can be used in the temperature range −20 °C to 82 °C.
The hoses specified are in the size range of nominal bore 50 to 500 and may be smooth bore, rough bore or armoured rough bore.
Hoses for use with petroleum products having an aromatic content greater than 50 % (v/v) are outside the scope of this document but the requirements may be used as a basis for such hoses on request to the manufacturer.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 6808:2014(Main)
Plastic hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:2014)
EN ISO 6808:2014

EN ISO 6808 specifies the requirements for two types of polymer-reinforced thermoplastics hose and hose assembly for suction and discharge applications with kerosene, heating oil, diesel fuel, and lubricating oils in the temperature range -10 °C to +45 °C.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1360:2013(Main)
Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
EN 1360:2013

This European Standard specifies minimum requirements for three types of hoses in two categories and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar. As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 and EN 590 should be carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1761:2000(Main)
Rubber hoses and hose assemblies for fuel truck delivery - Specification
EN 1761:1999

This European Standard specifies the requirements for two types of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar. Both types of hose are designed for: a) use with hydrocarbon fuels, having an aromatic hydrocarbon content not exceeding 50 % by volume and containing oxygenated compounds up to 15 %; b) operation within the temperature range of -30°C to +70°C, undamaged by climatic conditions of -50°C to 70°C when stored in static conditions.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13483:2022(Main)
Rubber and plastic hoses and hose assemblies with internal vapour recovery for measured fuel dispensing systems - Specification
EN 13483:2022

This document specifies the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.
The hose assemblies with vapour recovery for delivery systems on petrol filling stations need to be capable of withstanding anticipated mechanical, thermal and chemical stressing and be resistant to the combustible liquids used in these applications as well as their vapour and vapour air mixtures. It is imperative that the assemblies be constructed in such a way that actions during normal operation cannot give rise to dangerous electrostatic charges nor that there will be any reduction in the performance of the vapour recovery.
The assemblies are intended for use at ambient temperatures between –30 °C and +55 °C for normal temperature class and –40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar .
Hoses can be constructed from rubber or thermoplastic elastomer (TPE) and this document specifies the requirements for three types of hoses in two grades and two classes of hose assemblies for measured fuel dispensing systems, including oxygenated fuels (≤15 % oxygenated compounds) with internal vapour recovery tubing or hose.
NOTE   This document is not applicable to multi chamber fuel dispensing hoses.
As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 are carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1762:2019(Main)
Rubber hoses and hose assemblies for liquefied petroleum gas, LPG (liquid or gaseous phase), and natural gas up to 25 bar (2,5 MPa) - Specification
EN 1762:2018

This European Standard specifies the requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in liquid or gaseous phase and natural gas with a maximum working pressure of 25 bar (2,5 MPa) and vacuum within the temperature range of −30 °C to +70 °C and, when designated -LT, −50 °C to +70 °C.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1765:2016(Main)
Rubber hose assemblies for oil suction and discharge services - Specification for the assemblies
EN 1765:2016

This draft European Standard specifies the characteristics of four types of oil suction and discharge hose assemblies used for the conveyance of petroleum, including crude oils and other liquid petroleum products containing a maximum aromatics content of 50 % (v/v). It is not suitable for liquefied petroleum gas and natural gas.
Hose assemblies to this document can be used in the temperature range −20 °C to 82 °C.
The hoses specified are in the size range of nominal bore 50 to 500 and may be smooth bore, rough bore or armoured rough bore.
Hoses for use with petroleum products having an aromatic content greater than 50 % (v/v) are outside the scope of this document but the requirements may be used as a basis for such hoses on request to the manufacturer.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 6808:2014(Main)
Plastic hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids - Specification (ISO 6808:2014)
EN ISO 6808:2014

EN ISO 6808 specifies the requirements for two types of polymer-reinforced thermoplastics hose and hose assembly for suction and discharge applications with kerosene, heating oil, diesel fuel, and lubricating oils in the temperature range -10 °C to +45 °C.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day