SIST ETS 300 607-3 E7:2003
(Main)Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 3: Layer 3 (L3) Abstract Test Suite (ATS) (GSM 11.10-3 version 4.21.1)
Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 3: Layer 3 (L3) Abstract Test Suite (ATS) (GSM 11.10-3 version 4.21.1)
SUBJECT Use correct channels in TC_26_5_7_1_4 Corrections to handover test case 26_6_5_5_1 CS ATS implementation errors Cell Selection Implementation Errors Adjusting RF power levels in TC 26_7_4_3_1 Problem with use of lists as parameters Problems with TC 26_10_2_3 New Test Step (InitCM) Needed In-Order Use Custom Call Initiation TSOs CS ATS implementation errors (Modification of TC_20_6 suitable for Anite tester) Corrections to handover test case 26_6_5_5_2 Corrections to handover test case 26_6_5_7 Corrections to handover test case 26_6_5_9 Correction of 2nd TMSI-Reallocation in TC_26_7_1 Problems with TC 26_10_2_2 Corrections to handover test case 26_6_5_6 Corrections to TC 26_10_3_1 Simplification for checking of Mobile Time Difference IE in TCs 26_6_5_5_2, 26_6_5_6 and 26_6_5_7 Naming collision with FullRateCh_B_1 & Est_MO_Call_init in EFR Problem with test case TC_26_6_5_4_2 TTCN modifications to C_26_8_1_4_5_1, TC_26_8_1_4_4_1, Setup_10_3100, Setup_11_3100 and Setup_10_UDI Corrections to handover test case 26_6_5_8 Implementation problems with TC_26_6_5_3_2 Test case 26_8_2_1 problems Test case 26_8_1_4_3_2 problems Problems with TC 26_6_4_2_2 Problem with use of lists as parameters Problems with TC 26_10_2_5 TTCN modifications to TC_26_9_6_1_1
Digitalni celični telekomunikacijski sistem (faza 2) ¬– Specifikacija skladnosti za mobilne postaje (MS) – 3. del: Abstraktni preskušalni niz (ATS) tretje plasti (L3) (GSM 11.10-3 različica 4.21.1)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2003
'LJLWDOQLFHOLþQLWHOHNRPXQLNDFLMVNLVLVWHP ID]D ¤±6SHFLILNDFLMDVNODGQRVWL]D
PRELOQHSRVWDMH 06 ±GHO $EVWUDNWQLSUHVNXãDOQLQL] $76 WUHWMHSODVWL /
*60UD]OLþLFD
Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS)
conformance specification; Part 3: Layer 3 (L3) Abstract Test Suite (ATS) (GSM 11.10-3
version 4.21.1)
Ta slovenski standard je istoveten z: ETS 300 607-3 Edition 7
ICS:
33.070.50 Globalni sistem za mobilno Global System for Mobile
telekomunikacijo (GSM) Communication (GSM)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN ETS 300 607-3
TELECOMMUNICATION August 1998
STANDARD Seventh Edition
Source: SMG Reference: RE/SMG-071110PR5-3
ICS: 33.020
Key words: Digital cellular telecommunications system, Global System for Mobile Communication (GSM)
R
GLOBAL SYSTEM FOR
MOBILE COMMUNICATIONS
Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 3: Layer 3 (L3) Abstract Test Suite (ATS)
(GSM 11.10-3 version 4.21.1)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: secretariat@etsi.fr - http://www.etsi.fr - http://www.etsi.org
Tel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1998. All rights reserved.
Page 2
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Standards Making Support Dept." at the address shown on the title page.
Page 3
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
Contents
Foreword .5
1 Scope .7
2 Normative references.7
3 Definitions and abbreviations .10
3.1 Definitions .10
3.2 Abbreviations .10
4 Test Suite Structure (TSS) .11
4.1 Test suite naming convention .11
4.2 Suite Overview.12
4.3 Test groups.12
4.3.1 Valid Behaviour tests (BV) .12
4.3.2 Invalid Behaviour/Inopportune Behaviour tests (BI-BO).12
4.4 Test Step Structure.13
4.4.1 Preambles .13
4.4.2 Postambles.13
5 Test Purposes (TP).13
5.1 TP and test case naming convention.13
6 Abstract test method and test configurations.13
6.1 Test system model.13
6.2 Test Method.14
Annex A (normative): Layer 3 Abstract Test Suite .15
Annex B (normative): Partial IXIT proforma .1429
Introduction.1429
B.1 Identification Summary.1430
B.2 Abstract Test Suite Summary .1430
B.3 Test Laboratory .1430
B.3.1 Test Laboratory Identification.1430
B.3.2 Accreditation status of the test service .1431
B.3.3 Manager of Test Laboratory.1431
B.3.4 Contact person of Test Laboratory .1431
B.3.5 Means of Testing .1432
B.3.6 Instructions for Completion.1433
B.4 Client .1434
B.4.1 Client Identification.1434
B.4.2 Client Test Manager.1434
B.4.3 Client Contact person .1434
B.4.4 Test Facilities Required .1435
B.5 System Under Test.1436
B.5.1 SUT Information.1436
B.5.2 Limitations of the SUT .1437
B.5.3 Environmental Conditions.1438
Page 4
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
B.6 Ancillary Protocols . 1439
B.6.1 Ancillary Protocols 1. 1439
B.6.2 Ancillary Protocols 2. 1439
B.7 Protocol Layer Information for L3 of Mobile Station. 1439
B.7.1 Information provided for test purposes by the MS supplier. 1439
B.7.2 MMI information . 1452
B.7.3 Test house specified parameters. 1457
Annex C: PCTR Proforma. 1489
Annex D (normative): Enhanced Full Rate Abstract Test Suite. 1490
Annex E (informative): Cell Selection Abstract Test Suite. 1948
History. 2467
Page 5
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
Foreword
This European Telecommunication Standard (ETS) has been produced by the Special Mobile Group
(SMG) of the European Telecommunications Standards Institute (ETSI).
This ETS describes the technical characteristics and methods of test for Mobile Stations (MSs), operating
in the 900 MHz and 1 800 MHz frequency band (GSM 900 and DCS 1 800) within the digital cellular
telecommunications system.
This ETS corresponds to GSM technical specification GSM 11.10-3 version 4.21.1.
This part of the ETS (Part 3), contains Tree and Tabular Combined Notation (TTCN) for Layer 3,
signalling for MS supporting Enhanced Full Rate Speech, and cell selection conformity specifications for
which Mobile Stations, within the digital cellular telecommunications system (Phase 2), are tested for
compliance.
The graphical form ATS
The TTCN.GR representation of these ATSs are contained in annex A, annex D and annex E of this ETS.
The machine processable ATS
The electronic forms of the machine processable files (TTCN MP format) corresponding to the ATS for
Layer 3 are contained in the files L3-4l1.mp (Layer 3), EF-4l1.mp (Enhanced Full Rate), and CS-4l1.mp
1)
(Cell Selection) on the diskettes included as a part of this ETS (Part 3).
ETS 300 607 consists of three parts, which have the following ETS numbers and titles:
ETS 300 607-1 Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 1: Conformance specification
Reference: GSM 11.10-1.
ETS 300 607-2 Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 2: Protocol Implementation Conformance Statement (ICS)
proforma specification
Reference: GSM 11.10-2.
ETS 300 607-3 Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 3: Layer 3 (L3) Abstract Test Suite (ATS)
Reference: GSM 11.10-3.
Transposition dates
Date of adoption of this ETS: 24 July 1998
Date of latest announcement of this ETS (doa): 31 October 1998
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 30 April 1999
Date of withdrawal of any conflicting National Standard (dow): 30 April 1999
1) This file is located in an archive file named 6073_E7.ZIP. Other file formats are available on request.
Page 6
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
Blank page
Page 7
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
1 Scope
This European Telecommunication Standard (ETS) specifies the Abstract Test Suite (ATS) and partial
IXIT proforma for the Network Layer (Layer 3) at the mobile radio interface of the GSM or DCS (Phase 2)
mobile stations (MS) conforming to the ETSs for the Radio Resource management, the Mobility
Management, the circuit-switched Call Control, the Supplementary Services and Short Message Services
for the digital cellular telecommunications systems (Phase 2).
The ISO standards for the methodology of conformance testing are used as the basis for the test
specifications.
2 Normative references
This ETS incorporates by dated and undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this ETS only when incorporated in it by amendment or revision. For undated references, the
latest edition of the publication referred to applies.
[1] ISO/IEC 9646-1: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 1: General Concepts".
[2] ISO/IEC 9646-2: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 2: Abstract Test Suite Specification".
[3] ISO/IEC 9646-3: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 3: The Tree and Tabular Combined
Notation".
[4] ISO/IEC 9646-5: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 5: Requirements on test laboratories and
clients for the conformance assessment process".
[5] ISO/IEC 8824: "Information Technology-OSI- Specification of Abstract Syntax
Notation One (ASN.1)".
[6] ISO/IEC 8825: "Information Technology-OSI- Specification of Basic Encoding
Rules for Abstract Syntax Notation One (ASN.1)".
[7] ITU-T Recommendation Q.773: "Specifications of Signalling System No.7;
Transaction capabilities formats and encoding".
[8] ETS 300 287: "Integrated Services Digital Network (ISDN); Signalling System
No.7, Transaction Capabilities Application Part (TCAP) version 2".
[9] ETS 300 406 (January 1995): "Methods for Testing and Specification (MTS);
Protocol and profile conformance testing specifications; Standardization
methodology".
[10] ETS 300 501 (GSM 02.02 Version 4.2.2): "Digital cellular telecommunication
system (Phase 2); Bearer Services (BS) supported by a GSM Public Land
Mobile Network (PLMN)".
[11] ETS 300 502 (GSM 02.03 Version 4.3.1): "Digital cellular telecommunication
system (Phase 2); Teleservices supported by a GSM Public Land Mobile
Network (PLMN)".
[12] ETS 300 504 Edition 4 (GSM 02.06 Version 4.5.1): "Digital cellular
telecommunication system (Phase 2); Types of Mobile Stations (MS)".
[13] ETS 300 505 Edition 3 (GSM 02.07 Version 4.8.1): "Digital cellular
telecommunication system (Phase 2); Mobile Station (MS) features".
Page 8
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
[14] ETS 300 511 Edition 2 (GSM 02.30 Version 4.13.0): "Digital cellular
telecommunication system (Phase 2); Man-Machine Interface (MMI) of the
Mobile Station (MS)".
[15] ETS 300 523 Edition 2 (GSM 03.03 Version 4.9.0): "Digital cellular
telecommunication system (Phase 2); Numbering, addressing and
identification".
[16] ETS 300 527 Edition 2 (GSM 03.09 Version 4.6.0): "Digital cellular
telecommunications system (Phase 2); Handover procedures".
[17] ETS 300 528 (GSM 03.10 Version 4.3.1): "Digital cellular telecommunications
system (Phase 2); GSM Public Land Mobile Network (PLMN) connection types".
[18] ETS 300 529 Edition 3 (GSM 03.11 Version 4.10.1): "Digital cellular
telecommunication system (Phase 2); Technical realization of supplementary
services".
[19] ETS 300 530 (GSM 03.12 Version 4.4.2): "Digital cellular telecommunications
system (Phase 2); Location registration procedures".
[20] ETS 300 532 (GSM 03.14 Version 4.1.1): "Digital cellular telecommunications
system (Phase 2); Support of Dual Tone Multi-Frequency signalling (DTMF) via
the GSM system".
[21] ETS 300 535 Edition 4 (GSM 03.22 Version 4.11.0): "Digital cellular
telecommunication system (Phase 2); Functions related to Mobile Station (MS)
in idle mode".
[22] ETS 300 536 Edition 4 (GSM 03.40 Version 4.13.0): "Digital cellular
telecommunication system (Phase 2); Technical realization of the Short
Message Service (SMS) Point to Point (PP)".
[23] ETS 300 537 Edition 2 (GSM 03.41 Version 4.11.0): "Digital cellular
telecommunication system (Phase 2); Technical realization of Short Message
Service Cell Broadcast (SMSCB)".
[24] ETS 300 550 (GSM 04.01 Version 4.0.4): "Digital cellular telecommunications
system (Phase 2); Mobile Station - Base Station System (MS - BSS) interface
General aspects and principles".
[25] ETS 300 552 (GSM 04.03 Version 4.1.1): "Digital cellular telecommunications
system (Phase 2); Mobile Station - Base Station System (MS - BSS) interface
Channel structures and access capabilities".
[26] ETS 300 553 (GSM 04.04 Version 4.0.4): "Digital cellular telecommunication
system (Phase 2); layer 1 General requirements".
[27] ETS 300 554 (GSM 04.05 Version 4.0.3): "Digital cellular telecommunication
system (Phase 2); Data Link (DL) layer General aspects".
[28] ETS 300 555 (GSM 04.06 Version 4.4.0): "Digital cellular telecommunication
system (Phase 2); Mobile Station - Base Station System (MS - BSS) interface
Data Link (DL) layer specification".
[29] ETS 300 556 (GSM 04.07 Version 4.3.1): "Digital cellular telecommunication
system (Phase 2); Mobile radio interface signalling layer 3 General aspects".
[30] ETS 300 557 Edition 9 (GSM 04.08 Version 4.19.1): "Digital cellular
telecommunication system (Phase 2); Mobile radio interface layer 3
specification".
Page 9
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
[31] ETS 300 558 Edition 2 (GSM 04.10 Version 4.10.1): "Digital cellular
telecommunication system (Phase 2); Mobile radio interface layer 3
Supplementary services specification General aspects".
[32] ETS 300 559 Edition 4 (GSM 04.11 Version 4.10.0): "Digital cellular
telecommunication system (Phase 2); Point-to-Point (PP) Short Message
Service (SMS) support on mobile radio interface".
[33] ETS 300 560 Edition 3 (GSM 04.12 Version 4.6.0): "Digital cellular
telecommunication system (Phase 2); Short Message Service Cell Broadcast
(SMSCB) support on the mobile radio interface".
[34] ETS 300 564 Edition 3 (GSM 04.80 Version 4.11.1): "Digital cellular
telecommunication system (Phase 2); Mobile radio interface layer 3
supplementary services specification Formats and coding".
[35] ETS 300 565 (GSM 04.81 Version 4.4.1): "Digital cellular telecommunication
system (Phase 2); Line identification supplementary services - Stage 3".
[36] ETS 300 566 Edition 2 (GSM 04.82 Version 4.9.1): "Digital cellular
telecommunication system (Phase 2); Call Forwarding (CF) supplementary
services - Stage 3".
[37] ETS 300 567 Edition 2 (GSM 04.83 Version 4.6.1): "Digital cellular
telecommunication system (Phase 2); Call Waiting (CW) and Call Hold (HOLD)
supplementary services - Stage 3".
[38] ETS 300 568 (GSM 04.84 Version 4.3.2): "Digital cellular telecommunication
system (Phase 2); MultiParty (MPTY) supplementary services - Stage 3".
[39] ETS 300 569 Edition 2 (GSM 04.85 Version 4.1.1): "Digital cellular
telecommunications system (Phase 2); Closed User Group (CUG)
supplementary services - Stage 3".
[40] ETS 300 570 (GSM 04.86 Version 4.5.2): "Digital cellular telecommunication
system (Phase 2); Advice of Charge (AoC) supplementary services - Stage 3".
[41] ETS 300 571 Edition 2 (GSM 04.88 Version 4.7.1): "Digital cellular
telecommunication system (Phase 2); Call Barring (CB) supplementary services
- Stage 3".
[42] ETS 300 572 (GSM 04.90 Version 4.1.1): "Digital cellular telecommunication
system (Phase 2); Unstructured supplementary services operation - Stage 3".
[43] ETS 300 573 Edition 4 (GSM 05.01 Version 4.6.0): "Digital cellular
telecommunications system (Phase 2); Physical layer on the radio path General
description".
[44] ETS 300 574 Edition 6 (GSM 05.02 Version 4.9.1): "Digital cellular
telecommunication system (Phase 2); Multiplexing and multiple access on the
radio path".
[45] ETS 300 575 Edition 4 (GSM 05.03 Version 4.5.1): "Digital cellular
telecommunication system (Phase 2); Channel coding".
[46] ETS 300 576 (GSM 05.04 Version 4.0.3): "Digital cellular telecommunication
system (Phase 2); Modulation".
[47] ETS 300 577 Edition 13 (GSM 05.05 Version 4.21.0): "Digital cellular
telecommunication system (Phase 2); Radio transmission and reception".
[48] ETS 300 578 Edition 12 (GSM 05.08 Version 4.21.0): "Digital cellular
telecommunication system (Phase 2); Radio subsystem link control".
Page 10
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
[49] ETS 300 579 Edition 6 (GSM 05.10 Version 4.9.0): "Digital cellular
telecommunication system (Phase 2); Radio subsystem synchronisation".
[50] ETS 300 582 Edition 4 (GSM 07.01 Version 4.10.0): "Digital cellular
telecommunication system (Phase 2); General on Terminal Adaptation
Functions (TAF) for Mobile Stations (MS)".
[51] ETS 300 590 Edition 5 (GSM 08.08 Version 4.11.0): "Digital cellular
telecommunications system (Phase 2); Mobile-services Switching Centre - Base
Station System (MSC - BSS) interface Layer 3 specification".
[52] ETS 300 596 Edition 4 (GSM 08.58 Version 4.9.0): "Digital cellular
telecommunications system (Phase 2); Base Station Controller - Base
Transceiver Station (BSC - BTS) interface Layer 3 specification".
[53] ETS 300 599 Edition 7 (GSM 09.02 Version 4.17.0): "Digital cellular
telecommunication system (Phase 2); Mobile Application Part (MAP)
specification".
[54] ETS 300 607-1 Edition 7 (GSM 11.10-1 Version 4.20.0): "Digital cellular
telecommunications system (Phase 2); Mobile Station (MS) conformance
specification; Part 1: Conformance specification".
[55] ETS 300 607-2 Edition 2 (GSM 11.10-2 Version 4.15.0): "Digital cellular
telecommunications system (Phase 2); Mobile Station (MS) conformance
specification; Part 2: Protocol Implementation Conformance Statement (PICS)
Proforma specification".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this ETS, the following definitions apply:
Abstract Test Suite (ATS): Refer to ISO/IEC 9646-1 [1].
Implementation Under Test (IUT): Refer to ISO/IEC 9646-1 [1].
Partial Protocol Implementation eXtra Information for Testing (IXIT): Refer to ISO/IEC 9646-1 [1].
Point of Controls and Observations (PCO): Refer to ISO/IEC 9646-1 [1].
Protocol Implementation Conformance Statement (ICS): Refer to ISO/IEC 9646-1 [1].
System Under Test (SUT): Refer to ISO/IEC 9646-1 [1].
3.2 Abbreviations
For the purposes of this ETS, the following abbreviations apply:
ATS Abstract Test Suite
BI Invalid Behaviour tests
BO Inopportune Behaviour tests
BV Valid Behaviour tests
CA CApability tests
EDP-N Event Detection Point - Notification
EDP-R Event Detection Point - Request
ETS European Telecommunication Standard
FE Functional Entity
FSM Finite State Machine
ICS Implementation Conformance Statement
IUT Implementation Under Test
Page 11
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
IXIT Implementation eXtra Information for Testing
PDU Protocol Data Unit
SUT System Under Test
TP Test Purpose
TSS Test Suite Structure
Further abbreviations used within GSM related ETS may be found in ETR 100.
Abbreviations for test case group names may be found in figure 1 and 2.
4 Test Suite Structure (TSS)
4.1 Test suite naming convention
The test group identifier for each group and subgroup is built according to the scheme in figure 1.
Identifier: L3
= category: BIT BIT, Basic Interconnection tests (not used)
CA CA, Capability tests (not used)
BV BV, Valid Behaviour tests
BI-BOBI and BO, Invalid and Inopportune Behaviour tests
= group: IN Initial tests
ID Idle mode tests
RR Radio Resource management
MM Mobility Management
CC Call Control
SP Structured Procedures
SS Supplementary services
LLF Lower Layer Failures
UUE Unknown, Unforeseen or erroneous Elements
= group: CR Channel Request
AT IMSI detach and IMSI attach
SMT Sequenced MM / CC message transfer
EC Establishment Cause
IA Immediate assignment
PG Test of paging
MR Test of measurement report
ASS Test of the channel
HO Test of handover
FR Test of frequency redefinition
CMM Test of the channel mode modify procedure
CY Test of ciphering mode setting
CM Test of classmark
CHR Test of channel release
START Test of starting time
IDAU Identification and authentication
LU Location updating
CON MM connection
CCSMO State Machine Verification, Mobile Originating Call
CCSMT State Machine Verification, Mobile Terminating Call
SMICF State machine verification, In Call Functions
CRE Call Re-establishment
UUS User to user signalling
UPD Unknown protocol discriminator
TIS TI and skip indicator
UMT Undefined or unexpected message type
UIE Unforeseen information elements in the non-imperative
NMIE Non-semantical mandatory IE errors
CNR Unknown IE, comprehension not required
SB Spare bits
Page 12
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
= group: AC Handover / successful / active call
CUE Handover / successful / call under establishment
FSY Handover / successful / active call / finely synchronized
PRS Pre-synchronized handovers
PRF Protocol failures
ACC Location updating / accepted
REJ Location updating / rejected
ABN Location updating / abnormal cases
REL Location updating / release
PER Location updating / periodic
HPERLocation updating / periodic HPLMN search
IWAT Location updating / interworking of attach and periodic
EST MM connection / establishment
EXP MM connection / expiry
NWAB MM connection / abortion by the network
FRQPMM connection / follow-on request pending
U0 Mobile Originating Call U0 State
U0.1 Mobile Originating Call U0.1 MM Connection pending
U1 Mobile Originating Call U1 State
U3 Mobile Originating Call U3 State
U4 Mobile Originating Call U4 State
U10 Mobile Originating Call U10 State
U11 Mobile Originating Call U11 State
U12 Mobile Originating Call U12 State
U19 Mobile Originating Call U19 State
U0 Mobile Terminating Call U0 State
U6 Mobile Terminating Call U6 State
U9 Mobile Terminating Call U9 State
U7 Mobile Terminating Call U7 State
U8 Mobile Terminating Call U8 State
DTMFState machine verification, In Call Functions / transfer
CHC State machine verification, In Call Functions /
TICM State machine verification, In Call Functions / in-
OICM State machine verification, In Call Functions / in-
Figure 1: Test group identifier naming convention scheme
4.2 Suite Overview
Figure 2 shows the structure of the test suites for L3.
L3 ATS
BV BI/O
IN ID RR MM CC SP SS SMS LLF UUE
Figure 2: Test suite structure of the L3 tests
4.3 Test groups
4.3.1 Valid Behaviour tests (BV)
Predefined state transitions are considered as valid. The test purposes in the valid behaviour test
subgroup cover the verification of the normal and exceptional procedures of the various Finite State
Machines (FSMs), i.e. a valid behaviour test is a test where the message sequence and the message
contents are considered as valid.
4.3.2 Invalid Behaviour/Inopportune Behaviour tests (BI-BO)
This test sub group verifies that the Implementation Under Test (IUT) is able to react properly having
received an invalid Protocol Data Unit (PDU) or in the case an inopportune protocol event occurs. An
invalid PDU is defined as a syntactically incorrect message. An inopportune event is syntactically correct
but occurs when it is not expected, e.g. a correctly coded operation is received in a wrong state (the IUT
may respond Error UnexpectedComponentSequence).
Page 13
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
4.4 Test Step Structure
4.4.1 Preambles
The preamble is defined for each test purpose.
4.4.2 Postambles
After each test case the IUT shall be brought to the state as defined in the postamble for each test
purpose.
5 Test Purposes (TP)
For each conformance requirement a Test Purpose (TP) is defined. The test purposes are specified in the
ATS Dynamic part (annex A).
5.1 TP and test case naming convention
In order clearly to map the conformance requirements specified in the prETS 300 607-1 and TTCN test
cases in the ATS, the section numbers in the prETS 300 607-1 are used as test case names.
The identifier of each TP is identical to the name of the implemented TTCN test case.
"Test Purpose Identifier" = "Test Case Name" = TPI = TC_NN_A_B_C_D_E, where NN, A, B, C, D and E
are digits used in the corresponding section numbers of prETS 300 607-1. For example, the test case
name TC_26_5_6_2 is the TTCN specification corresponding to the conformance requirements in the
section 26.5.6.1.2 in the prETS 300 607-1. In case where the section has been implemented in more than
one test case sub numbering has been introduced. For example, the section 26.7.4.2.4 of
prETS 300 607-1, Location updating/rejected/national roaming testing is split into 5 test cases. The
corresponding TCs are identified as TC_26_7_4_2_4_1, TC_26_7_4_2_4_2, TC_26_7_4_2_4_3,
TC_26_7_4_2_4_4 and TC_26_7_4_2_4_5, respectively.
6 Abstract test method and test configurations
The distributed test method applies to the L3 MS testing. The test method uses a lower tester and a
Man-Machine Interface (MMI) as an upper tester at the SUT.
6.1 Test system model
The model of the L3 test system is based on the original protocol architecture at the air interface. The test
system consists conceptually of a lower tester LT, the L3 test programme (executable test suite), a L2
radio link emulator, a management functional unit, the L1 service provider and a TRx set (see figure 1).
Test operator
SUT
LT
L3 test programme
IUT
L3
PCO
L2
L2 emulator
Mngt
L1 L1
TRx set TRx
MS
Test system
Radio connection
Figure 3: Test system and distributed test method
Page 14
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
The LT provides the test environment and for test execution and the means of control and observation at
the L3 lower service boundary within the test system.
The L3 TTCN test specification uses the three LT interfaces to communicate with the MS, the system
under test, and with the other parts of the test system:
- Interface to the L2 emulator via the PCO;
- Interface to the management functional unit via TTCN test suite operations;
- Interface to the MS Man-Machine Interface (MMI) via a test operator.
6.2 Test Method
The PCO in the LT is defined as L2 SAP (SAP 0 + 3). The PCO has two FIFO queues (data buffers) to
store all sending and receiving test events. The L2 primitives in the ATS which constitute mainly the
interface to the L2 emulator are specified via the L2 primitives. In order to simulate multicell testing as
required in some test cases, the defined primitives are able to address individual cells of the test system
and the logic channels of each cell for the L3 message exchanges. The L2 emulator together with the
underlying L1 and the TRx set support all message exchanges via correct radio links.
The management function unit has three management functions:
• L2 and L1 management;
• Channel management;
• TRx management;
The interface to the management function unit is presented in the ATS via a set of test suite operations.
The major functions of the test suite management operations are:
• To load configuration parameters necessary for the test system.
• To control and get the necessary values of radio resources/ channels for tests.
The SUT (MS) has a more or less standardized MMI, such as keys, digital display, tones, etc. The ATS
uses such kind of functions to provoke some procedures or to observe simple results at the SUT side. A
human operator is needed during the test. The test system shall have an interface to the human operator
to enable the test co-ordination.
Page 15
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
Annex A (normative): Layer 3 Abstract Test Suite
Suite overview
Suite structure
Test Suite Structure
GSM_L3_MS_v4210
Suite Name:
Standards Ref: ETS 300 557
PICS Ref:
PIXIT Ref:
Distributed Single Layer Test Method
Test Method(s):
Comments: Version 4.21.0
Structure and Objectives
Test Group Reference Selection Ref Test Group Objective Page Nr
GSM_L3_MS_v4210/General/ SelExpr_0000 To verify the supported and non- 664
supported services.
GSM_L3_MS_v4210/InitialTest/ SelExpr_0100 To verify random access procedure, IMSI 679
attatch and detach procedure, sequenced
MM/CC message transfer and
establishment causes.
GSM_L3_MS_v4210/IdleMode/ SelExpr_0200 To verify MS functions in idle mode 705
GSM_L3_MS_v4210/BiBo/ SelExpr_0300 To verify the MS handling unknown, 708
unforeseen and erroneous protocol data,
and parallel transactions
GSM_L3_MS_v4210/RR/ SelExpr_0400 To verify the elementary procedures for 746
radio resource management
GSM_L3_MS_v4210/MM/ SelExpr_0500 To verify the elementary procedures of 908
mobility management.
GSM_L3_MS_v4210/CC/ SelExpr_0600 To verify the circuit switched call cntrol 973
functions.
GSM_L3_MS_v4210/StructureProc/ SelExpr_0700 To verify the structured procedures. 1081
GSM_L3_MS_v4210/EGSMSignalling/ SelExpr_1000 To verify the different procedures which 1103
may be impacted when some channel
uses E- GSM frequencies.
GSM_L3_MS_v4210/SS/ SelExpr_0800 To verify the functions of supplementary 1126
services.
GSM_L3_MS_v4210/SM/ SelExpr_0900 To verify the functions of short message 1219
service.
Detailed Comments:
Page 16
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
Test case index
Test Case Index
Test Group Test Case Id Selection ref Description Page Nr
Reference
GSM_L3_MS_v4210/ TC_11_1_1 SelExpr_0002 Verification of support and non-support of 661
General/ services (MT).
GSM_L3_MS_v4210/ TC_11_1_2 SelExpr_0007 Verification of support and non-support of 663
General/ services (MO).
GSM_L3_MS_v4210/ TC_11_2 SelExpr_0002 Verification of support of the single numbering 668
General/ scheme.
GSM_L3_MS_v4210/ TC_11_3 SelExpr_0003 Verification of non-support of services. 669
General/ (Advice of Charge Charging, AOCC)
GSM_L3_MS_v4210/ TC_11_4 SelExpr_0004 Verification of non-support of services. (Call 672
General/ Hold)
GSM_L3_MS_v4210/ TC_11_5 SelExpr_0005 Verification of non-support of services. 673
General/ (MultiParty)
GSM_L3_MS_v4210/ TC_11_6 SelExpr_0006 Verification of non-support of feature. (Fixed 675
General/ dialling number)
GSM_L3_MS_v4210/I TC_26_2_1_1 SelExpr_0101 Initial Layer 3 tests - Channel request / initial 676
nitialTest/ time.
11.10 Ref. ver.4.10; CR
GSM_L3_MS_v4210/I TC_26_2_1_2 SelExpr_0101 Initial Layer 3 tests - Channel request / 678
nitialTest/ repetition time.
11.10 Ref. ver.4.10; CR: C46
GSM_L3_MS_v4210/I TC_26_2_1_3 SelExpr_0101 Initial Layer 3 tests - Channel request / 680
nitialTest/ random reference.
11.10 Ref. ver.4.10; CR
GSM_L3_MS_v4210/I TC_26_2_2 SelExpr_0101 IMSI detach and IMSI attach. 681
nitialTest/
11.10 Ref. ver 4.10.0; CR. 0295-6r1.
CR.C62r1.
GSM_L3_MS_v4210/I TC_26_2_3 SelExpr_0101 Sequenced MM / CM message transfer. 683
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_1 SelExpr_0102 Establishment Cause /pr1 (TCH) 685
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_2 SelExpr_0103 Establishment Cause /pr2 ( /H) 687
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_3 SelExpr_0107 Establishment Cause /pr3 (TCH/FS) 689
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_4 SelExpr_0104 Establishment Cause /pr4 (data) 691
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_5 SelExpr_0101 Establishment Cause /pr5 693
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_6 SelExpr_0101 Establishment Cause /pr6 696
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_7 SelExpr_0105 Establishment Cause /pr7 (non-call-SS) 699
nitialTest/
GSM_L3_MS_v4210/I TC_26_2_4_8 SelExpr_0106 Establishment Cause /pr8 (SMS/PP MO) 701
nitialTest/
GSM_L3_MS_v4210/I TC_26_3_2 SelExpr_0201 MS indication of available PLMNs 702
dleMode/
GSM_L3_MS_v4210/I TC_26_3_3 SelExpr_0201 MS will send only if BSS is "on air". 703
dleMode/
GSM_L3_MS_v4210/I TC_26_3_4 SelExpr_0201 Manual mode of PLMN selection 704
dleMode/
11.10 Ref. ver. 4.10.0; CR. 11.10-661. C64
GSM_L3_MS_v4210/ TC_26_5_1 SelExpr_0302 Handling of unknown protocol discriminator 705
BiBo/
GSM_L3_MS_v4210/ TC_26_5_2_1_1 SelExpr_0302 Handling of unknown TI and skip indicator / 706
BiBo/ RR
GSM_L3_MS_v4210/ TC_26_5_2_1_2 SelExpr_0302 TI Skip indicator / RR / RR Connection 707
BiBo/ established
GSM_L3_MS_v4210/ TC_26_5_2_2 SelExpr_0302 TI and skip indicator / MM 709
BiBo/
GSM_L3_MS_v4210/ TC_26_5_2_3 SelExpr_0301 TI and skip indicator / CC 711
BiBo/
GSM_L3_MS_v4210/ TC_26_5_3_1 SelExpr_0301 Undefined or unexpected Message type / 713
BiBo/ undefined message type / CC
GSM_L3_MS_v4210/ TC_26_5_3_2 SelExpr_0301 Undefined or unexpected message type / 714
BiBo/ undefined message type / MM
Page 17
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
GSM_L3_MS_v4210/ TC_26_5_3_3 SelExpr_0302 Undefined or unexpected message type / 715
BiBo/ undefined message type / RR
GSM_L3_MS_v4210/ TC_26_5_3_4 SelExpr_0301 Undefined or unexpected message type / 716
BiBo/ unexpected message type / CC
GSM_L3_MS_v4210/ TC_26_5_4_1 SelExpr_0302 Unforeseen info elements in non-imperative 717
BiBo/ message part / duplicated info elements
GSM_L3_MS_v4210/ TC_26_5_5_1_1_1 SelExpr_0302 Non-semantical mandatory IE errors / RR / 718
BiBo/ missing mandatory IE error / special case
GSM_L3_MS_v4210/ TC_26_5_5_1_1_2 SelExpr_0302 Non-semantical mandatory IE errors / RR / 719
BiBo/ missing mandatory IE error / general case
GSM_L3_MS_v4210/ TC_26_5_5_1_2 SelExpr_0302 Non-semantical mandatory ie errors / RR / 720
BiBo/ comprehension required
GSM_L3_MS_v4210/ TC_26_5_5_2_1 SelExpr_0301 Non-semantical mandatory IE errors / MM / 721
BiBo/ syntactically incorrect mandatory IE
GSM_L3_MS_v4210/ TC_26_5_5_2_2 SelExpr_0302 Non-semantical mandatory IE errors / MM / 722
BiBo/ syntactically incorrect mandatory IE
11.10 Ref. ver. 4.10.0; CR. 11.10-688
GSM_L3_MS_v4210/ TC_26_5_5_2_3 SelExpr_0302 Non-semantical mandatory IE errors / MM / 723
BiBo/ syntactically incorrect mandatory IE
GSM_L3_MS_v4210/ TC_26_5_5_3_1_1 SelExpr_0301 Non-semantical mandatory IE errors / CC / 725
BiBo/ missing mandatory IE / disconnect message
GSM_L3_MS_v4210/ TC_26_5_5_3_1_2 SelExpr_0301 Non-semantical mandatory IE errors / CC / 726
BiBo/ missing mandatory IE / general case
GSM_L3_MS_v4210/ TC_26_5_5_3_2 SelExpr_0301 Non-semantical mandatory IE errors / CC / 727
BiBo/ comprehension required
GSM_L3_MS_v4210/ TC_26_5_6_1_1 SelExpr_0302 Unknown IE, comprehension not required / 728
BiBo/ MM / IE unknown in the protocol
GSM_L3_MS_v4210/ TC_26_5_6_1_2 SelExpr_0302 Unknown IE, comprehension not required / 730
BiBo/ MM / IE unknown in the message
GSM_L3_MS_v4210/ TC_26_5_6_2_1 SelExpr_0301 Unknown info elements in the non-imperative 731
BiBo/ message part / CC / Call establishment
GSM_L3_MS_v4210/ TC_26_5_6_2_2 SelExpr_0301 Unknown information elements in the non- 732
BiBo/ imperative message part / CC / disconnect
GSM_L3_MS_v4210/ TC_26_5_6_2_3 SelExpr_0301 Unknown information elements in the non- 733
BiBo/ imperative message part / CC / release
GSM_L3_MS_v4210/ TC_26_5_6_2_4 SelExpr_0301 Unknown info elements in the non-imperative 734
BiBo/ message part / CC / release complete
GSM_L3_MS_v4210/ TC_26_5_6_3 SelExpr_0302 Unknown IE in the non-imperative message 735
BiBo/ part, comprehension not required / RR /
unknown in the protocol.
GSM_L3_MS_v4210/ TC_26_5_7_1_1 SelExpr_0302 Spare bits / RR / paging channel 736
BiBo/
GSM_L3_MS_v4210/ TC_26_5_7_1_2 SelExpr_0302 Spare bits / RR / BCCH 737
BiBo/
GSM_L3_MS_v4210/ TC_26_5_7_1_3 SelExpr_0302 pare bits / RR / AGCH 738
BiBo/
GSM_L3_MS_v4210/ TC_26_5_7_1_4 SelExpr_0302 Spare bits / RR / connected mode 739
BiBo/
GSM_L3_MS_v4210/ TC_26_5_7_2 SelExpr_0302 Spare bits / MM 740
BiBo/
GSM_L3_MS_v4210/ TC_26_5_7_3 SelExpr_0301 Spare bits / CC 741
BiBo/
GSM_L3_MS_v4210/ TC_26_6_1_1 SelExpr_0401 Immediate Assignment / SDCCH or TCH 743
RR/ assignment
GSM_L3_MS_v4210/ TC_26_6_1_2 SelExpr_0401 Immediate Assignment / extended 745
RR/ assignment
GSM_L3_MS_v4210/ TC_26_6_1_3 SelExpr_0401 Immediate Assignment / assignment rejection 748
RR/
GSM_L3_MS_v4210/ TC_26_6_1_4 SelExpr_0401 Immediate Assignment / ignore assignment 751
RR/
GSM_L3_MS_v4210/ TC_26_6_1_5 SelExpr_0401 Immediate Assignment after immediate 753
RR/ assignment reject
GSM_L3_MS_v4210/ TC_26_6_2_1_1 SelExpr_0401 Paging / normal / type 1 754
RR/
GSM_L3_MS_v4210/ TC_26_6_2_1_2 SelExpr_0401 Paging / normal / type 2 756
RR/
GSM_L3_MS_v4210/ TC_26_6_2_1_3 SelExpr_0401 Paging / normal / type 3 758
RR/
GSM_L3_MS_v4210/ TC_26_6_2_2 SelExpr_0401 Paging / extended 760
RR/
GSM_L3_MS_v4210/ TC_26_6_2_3_1 SelExpr_0401 Paging / reorganisation / procedure 1 764
Page 18
ETS 300 607-3 (GSM 11.10-3 version 4.21.1): August 1998
RR/
GSM_L3_MS_v4210/ TC_26_6_2_3_2 SelExpr_0401 Paging / reorganisation / procedure 2 766
RR/
GSM_L3_MS_v4210/ TC_26_6_2_4 SelExpr_0401 Paging / same as before 768
RR/
GSM_L3_MS_v4210/ TC_26_6_2_5 SelExpr_0401 Multislot CCCH handling 769
RR/
GSM_L3_MS_v4210/ TC_26_6_3_1 SelExpr_0402 Measurement / no neighbour 771
RR/
GSM_L3_MS_v4210/ TC_26_6_3_2 SelExpr_0402 Measurement / all neighbours present 773
RR/
GSM_L3_MS_v4210/ TC_26_6_3_3 SelExpr_0402 Measurement / barred cells and non- 775
RR/ permitted NCCs
GSM_L3_MS_v4210/ TC_26_6_3_4 SelExpr_0402 Measurement / DTX 777
RR/
GSM_L3_MS_v4210/ TC_26_6_3_5 SelExpr_0402 Measurement / frequency formats 781
RR/
GSM_L3_MS_v4210/ TC_26_6_4_1 SelExpr_0401 Dedicated assignment / Successful case 784
RR/
GSM_L3_MS_v4210/ TC_26_6_4_2_1 SelExpr_0402 Dedicated assignment / failure / failure during 790
RR/ active state
GSM_L3_MS_v4210/ TC_26_6_4_2_2 SelExpr_0401 Dedicated assignment / failure / genaral case 792
RR/
GSM_L3_MS_v4210/ TC_26_6_5_1 SelExpr_0402 Handover / successful / active call / non- 794
RR/ synchronized
GSM_L3_MS_v4210/ TC_26_6_5_2_1 SelExpr_0410 Retransmit L3-msg during non synchr. HO 799
RR/ from SDCCH/4_nonFH to TCH/F_FH.
GSM_L3_MS_v4210/ TC_26_6_5_2_2 SelExpr_0408 Retransmit L3-msg during non synchr. HO 801
RR/ from SDCCH/4_nonFH to TCH/H_FH.
GSM_L3_MS_v4210/ TC_26_6_5_2_3 SelExpr_0410 Retransmit L3-msg during non synchr. HO 803
RR/ from SDCCH/4_nonFH to SDCCH/8_FH.
GSM_L3_MS_v4210/ TC_26_6_5_2_4 SelExpr_0410 Retransmit L3-msg during non synchr. HO 805
RR/ from SDCCH/8_nonFH in cell A to
SDCCH/8_FH in cellB.
GSM_L3_MS_v4210/ TC_26_6_5_2_5 SelExpr_0408 Retransmit L3-msg during non synchr. HO 808
RR/ from TCH/F_NonFH in cell A to
TCH/H_NonFH in cellB.
GSM_L3_MS_v4210/ TC_26_6_5_2_6 SelExpr_0408 Retransmit L3-msg during non synchr. HO 810
RR/ from TCH/H_FH in cell A to TCH/F_FH in
cellB.
GSM_L3_MS_v4210/ TC_26_6_5_2_7 SelExpr_0410 Retransmit L3-msg during non synchr. HO 812
RR/ from TCH/F_FH in cell A to TCH/F_FH in
cellB.
GSM_L3_MS_v4210/ TC_26_6_5_2_8 SelExpr_0410 Retransmit L3-msg during non synchr. HO 814
RR/ from TCH/SDCCH8_FH in cell A to
TCH/F_NonFH in cellB.
GSM_L3_MS_v4210/ TC_26_6_5_2_9 SelExpr_0410 Retransmit L3-msg during non synchr. HO 816
RR/ from SDCCH8_NoFH in cell A to TCH/F_FH
in cellB.
GSM_L3_MS_v4210/ TC_26_6_5_2_10 SelExpr_0408 Retransmit L3-msg during non synchr. HO 818
RR/ from TCH/SDCCH8_NoFH in cell A to
TCH/H_FH in cellB.
GSM_L3_MS_v4210/ TC_26_6_5_3_1 SelExpr_0402 synchronised HO from TCH/F_FH in cellA to 820
RR/ TCH/F_nonFH in cellB.
GSM_L3_MS_v4210/ TC_26_6_5_3_2 SelExpr_0408 synchronised HO from TCH/H_FH in cellA to 82
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...