SIST EN 17109:2020/kprA1:2024
(Amendment)Mountaineering equipment - Individual safety systems for rope courses - Safety requirements and test methods
Mountaineering equipment - Individual safety systems for rope courses - Safety requirements and test methods
This document specifies safety requirements and test methods for components of an individual safety system for protection against a fall from height used in permanent and mobile rope courses as defined in EN 15567-1.
The products considered in this standard are not intended to limit, by themselves, the deceleration of the fall of the user, as defined in EN 15567-1. For this requirement, it is essential to consider the whole ropes course system.
Safety lines and harness are not covered in this standard.
1 Modification to Clause 1, Scope
1. Replace "EN 15567-1" twice with "EN 15567-1:2015+A1:2020";
2. Replace "standard" with "document" (twice in this clause).
Bergsteigerausrüstung - Einzelsicherungssysteme für Seilgärten - Sicherheitsanforderungen und Prüfverfahren
1 Änderungen in Abschnitt 1, Anwendungsbereich
1. Ersetze „EN 15567-1“ zweimal mit „EN 15567 1:2015+A1:2020“;
2. Ersetze „Norm“ mit „Dokument“ (zweimal in diesem Abschnitt).
Équipement d’alpinisme et d’escalade - Systèmes d’assurage individuels pour parcours acrobatiques en hauteur - Exigences de sécurité et méthodes d’essai
1 Modification de l’Article 1, Domaine d’application
1. Remplacer deux fois « EN 15567-1 » par « EN 15567 1:2015+A1:2020 » ;
2. Remplacer « la présente norme » par « le présent document » (deux fois dans cet article).
Gorniška oprema - Vrvni plezalni parki - Individualni varnostni sistem - Varnostne zahteve in preskusne metode - Dopolnilo A1
General Information
Relations
Overview
EN 17109:2020/FprA1 (CEN) covers mountaineering equipment - individual safety systems for rope courses - safety requirements and test methods. This draft amendment updates the 2020 document and clarifies scope and test requirements for components of an individual safety system (ISS) used to protect users from falls on permanent and mobile rope courses defined in EN 15567‑1:2015+A1:2020. The document focuses on ISS components (e.g., MCDs, lanyards, connectors and related fittings) rather than on safety lines or harnesses, and emphasizes that individual products are not, by themselves, intended to limit fall deceleration - the whole ropes course system must be considered.
Key topics and technical requirements
- Scope updates: references to EN 15567‑1 updated to EN 15567‑1:2015+A1:2020; wording changed from “standard” to “document” in clause 1.
- Normative references: addition of EN 362:2004 (connectors) and multiple cross‑references updated to reflect A1 amendments.
- Use of certified connectors: Connectors certified to EN 12275:2013 or EN 362:2004 may be used in ISS without additional compliance to this document (see clause 4.1), with manufacturer guidance.
- Test methods and strength:
- Transversal static strength testing references clarified to specific subclauses (5.3.5.1–5.3.5.2).
- When tested per 5.3.5.2, the registered maximum transverse strength shall not be below 6 kN.
- Multiple foreseeable loading positions must be tested for static and deformation tests where applicable.
- Design and marking: requirements for non‑openable connections within reach of the user; manufacturer’s instructions and information must be provided (replaces former “information supplied by the manufacturer”). Marking references updated to EN 17109:2020+A1:2023.
- Documentation changes: new and revised clauses for manual extraction, deformation, handling and static strength tests; Annexes updated to restrict some compatibility tests to categories D and E MCDs.
Applications and users
This document is essential for:
- Manufacturers of ISS components (MCDs, lanyards, connectors, pulleys)
- Test laboratories and conformity assessment bodies performing safety and strength testing
- Rope course designers, installers and operators who need to ensure component compatibility and safe system integration
- Regulatory and certification authorities assessing PPE and recreational safety equipment
Practical benefits include harmonised safety requirements, clearer test methods, and improved manufacturer guidance to support safer rope‑course installations.
Related standards
- EN 15567‑1:2015+A1:2020 (rope courses - general)
- EN 12275:2013 (connectors)
- EN 362:2004 (connectors - personal protective equipment)
- EN 17109:2020+A1:2023 (amended version / marking)
- Referenced mountaineering standards from Annex B: EN 892:2012+A2:2021, EN 959:2018, EN 12277:2015+A1:2018, EN 13089:2011+A2:2021, EN 16869:2017, EN 17520:2021
Keywords: mountaineering equipment, individual safety systems, rope courses, safety requirements, test methods, EN 17109:2020, MCD, lanyard, safety line, connector, EN 15567‑1.
Frequently Asked Questions
SIST EN 17109:2020/kprA1:2024 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Mountaineering equipment - Individual safety systems for rope courses - Safety requirements and test methods". This standard covers: This document specifies safety requirements and test methods for components of an individual safety system for protection against a fall from height used in permanent and mobile rope courses as defined in EN 15567-1. The products considered in this standard are not intended to limit, by themselves, the deceleration of the fall of the user, as defined in EN 15567-1. For this requirement, it is essential to consider the whole ropes course system. Safety lines and harness are not covered in this standard. 1 Modification to Clause 1, Scope 1. Replace "EN 15567-1" twice with "EN 15567-1:2015+A1:2020"; 2. Replace "standard" with "document" (twice in this clause).
This document specifies safety requirements and test methods for components of an individual safety system for protection against a fall from height used in permanent and mobile rope courses as defined in EN 15567-1. The products considered in this standard are not intended to limit, by themselves, the deceleration of the fall of the user, as defined in EN 15567-1. For this requirement, it is essential to consider the whole ropes course system. Safety lines and harness are not covered in this standard. 1 Modification to Clause 1, Scope 1. Replace "EN 15567-1" twice with "EN 15567-1:2015+A1:2020"; 2. Replace "standard" with "document" (twice in this clause).
SIST EN 17109:2020/kprA1:2024 is classified under the following ICS (International Classification for Standards) categories: 97.220.40 - Outdoor and water sports equipment. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 17109:2020/kprA1:2024 has the following relationships with other standards: It is inter standard links to SIST EN 17109:2020+A1:2024, SIST EN 17109:2020. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 17109:2020/kprA1:2024 is associated with the following European legislation: EU Directives/Regulations: 2016/425; Standardization Mandates: M/571, M/571 AMD 1. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 17109:2020/kprA1:2024 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 17109:2020/oprA1:2022
01-december-2022
Gorniška oprema - Vrvni plezalni parki - Individualni varnostni sistem - Varnostne
zahteve in preskusne metode - Dopolnilo A1
Mountaineering equipment - Individual safety systems for rope courses - Safety
requirements and test methods
Bergsteigerausrüstung - Einzelsicherungssysteme für Seilgärten -
Sicherheitsanforderungen und Prüfverfahren
Équipement d’alpinisme et d’escalade - Systèmes d’assurage individuels pour parcours
acrobatiques en hauteur - Exigences de sécurité et méthodes d’essai
Ta slovenski standard je istoveten z: EN 17109:2020/prA1
ICS:
97.220.40 Oprema za športe na Outdoor and water sports
prostem in vodne športe equipment
SIST EN 17109:2020/oprA1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 17109:2020/oprA1:2022
SIST EN 17109:2020/oprA1:2022
DRAFT
EUROPEAN STANDARD
EN 17109:2020
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
October 2022
ICS 97.220.40
English Version
Mountaineering equipment - Individual safety systems for
rope courses - Safety requirements and test methods
Équipement d'alpinisme et d'escalade - Systèmes Bergsteigerausrüstung - Einzelsicherungssysteme für
d'assurage individuels pour parcours acrobatiques en Seilgärten - Sicherheitsanforderungen und
hauteur - Exigences de sécurité et méthodes d'essai Prüfverfahren
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 136.
This draft amendment A1, if approved, will modify the European Standard EN 17109:2020. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17109:2020/prA1:2022 E
worldwide for CEN national Members.
SIST EN 17109:2020/oprA1:2022
EN 17109:2020/prA1:2022
Contents Page
European foreword . 3
1 Modifications to Clause 1, Scope . 4
2 Modifications to Clause 2, Normative references . 4
3 Modification Clause 3, Terms and definitions . 4
4 Modifications to 4.1, Design and construction . 4
5 Modifications to 4.3.4, MCD transversal static strength test . 4
6 Modifications to 4.4, Locking devices of the opening of the MCD . 5
7 Modification to 4.5, Stability of tape . 5
8 Modifications to 5.1, Design and construction . 5
9 Modifications to 5.2, Manual extraction test for categories C, D and E. 5
10 Modifications to 5.3.1, General . 5
11 Modifications to 5.3.2, Function under a test load (only for MCD with pulleys) . 5
12 Modifications to 5.3.3, Deformation test for MCD of category E and to A to D where relevant
............................................................................................................................................................................... 5
13 Modifications to 5.3.4, Static strength test for all ISS or their component . 6
14 Modifications to 5.3.5.1, General . 6
15 Modifications to 5.3.5.2, Transverse test . 6
16 Modifications to 5.3.5.3, Transversal handling test . 6
17 Modification to Clause 6, Marking . 6
18 Modifications to Clause 7, Information supplied by the manufacturer . 6
19 Modifications to Annex A, Compatibility of MCD with safety line supports . 7
20 Modifications to Annex B, Standards on mountaineering equipment . 7
21 Modification to Annex ZA, Relationship between this European Standard and the essential
requirements of Regulation (EU) 2016/425 of the European Parliament and of the Council
of 9 March 2016 on personal protective equipment aimed to be covered . 7
22 Deletion of Bibliography . 7
SIST EN 17109:2020/oprA1:2022
EN 17109:2020/prA1:2022
European foreword
This document (EN 17109:2020/prA1:2022) has been prepared by Technical Committee CEN/TC 136
“Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by
DIN.
This document is currently submitted to the CEN Enquiry.
SIST EN 17109:2020/oprA1:2022
EN 17109:2020/prA1:2022
1 Modifications to Clause 1, Scope
1. Replace “EN 15567-1” twice with “EN 15567-1:2015+A1:2020”;
2. Replace “standard” with “document” (twice in this clause).
2 Modifications to Clause 2, Normative references
1. Add “EN 362:2004, Personal protective equipment against falls from a height — Connectors”;
2. Replace “EN 15567-1:2015” with” EN 15567-1:2015+A1:2020”.
3 Modification Clause 3, Terms and definitions
1. In 3.1 and 3.3, replace “EN 15567-1:2015” with “EN 15567-1:2015+A1:2020”.
4 Modifications to 4.1, Design and construction
1. Add in the beginning: “Connectors which are used as MCD and are certified according to EN 12275:2013
or EN 362:2004 can be used in ISS without complying to this document.
NOTE More information about the use of connectors certified according to EN 12275:2013 or EN 362
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...