SIST EN 12697-22:2020/oprA1:2023
(Amendment)Bituminous mixtures - Test methods - Part 22: Wheel tracking
Bituminous mixtures - Test methods - Part 22: Wheel tracking
This document describes test methods for determining the susceptibility of bituminous materials to deform under load. The test is applicable to mixtures with upper sieve size less than or equal to 32 mm.
The tests are applicable to specimens prepared from asphalt mixtures that have either been manufactured in a laboratory or cut from a pavement; test specimens are held in a mould with their surface flush with the upper edge of the mould.
The susceptibility of bituminous materials to deform is assessed by the rut formed by repeated passes of a loaded wheel at constant temperature. Three alternative types of device can be used according to this standard: large-size devices, extra large-size devices and small-size devices. With large-size devices and extra large-size devices, the specimens are conditioned in air during testing. With small-size devices, specimens are conditioned, in either air or water.
NOTE Large-size and extra large-size devices are not suitable for use with cylindrical cores.
Asphalt - Prüfverfahren - Teil 22: Spurbildungstest
Mélanges bitumineux - Méthodes d'essai - Partie 22 : Essai d’orniérage
No scope available
Bitumenske zmesi - Preskusne metode - 22. del: Preskus nastajanja kolesnic - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 12697-22:2020/oprA1:2023
01-september-2023
Bitumenske zmesi - Preskusne metode - 22. del: Preskus nastajanja kolesnic -
Dopolnilo A1
Bituminous mixtures - Test methods - Part 22: Wheel tracking
Asphalt - Prüfverfahren - Teil 22: Spurbildungstest
Mélanges bitumineux - Méthodes d'essai - Partie 22 : Essai d’orniérage
Ta slovenski standard je istoveten z: EN 12697-22:2020/prA1
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
SIST EN 12697-22:2020/oprA1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12697-22:2020/oprA1:2023
---------------------- Page: 2 ----------------------
SIST EN 12697-22:2020/oprA1:2023
DRAFT
EUROPEAN STANDARD
EN 12697-22:2020
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
June 2023
ICS 93.080.20
English Version
Bituminous mixtures - Test methods - Part 22: Wheel
tracking
Mélanges bitumineux - Méthodes d'essai - Partie 22 : Asphalt - Prüfverfahren - Teil 22: Spurbildungstest
Essai d'orniérage
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 227.
This draft amendment A1, if approved, will modify the European Standard EN 12697-22:2020. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12697-22:2020/prA1:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12697-22:2020/oprA1:2023
EN 12697-22:2020/prA1:2023 (E)
Contents Page
European foreword . 3
1 Modification to Clause 1, “Scope” . 4
2 Modification to Clause 3, “Terms and definitions” . 4
3 Modification to Clause 4, “Symbols and abbreviated terms” . 4
4 Modification to Clause 6.2, “Extra large devices”. 5
5 Modification to Clause 6.4.1, “General” . 5
6 Modification to Clause 7.1, “Test portion” . 6
7 Modification to Clause 7.2.2.1, “Cut specimens” . 6
8 Modification to Clause 7.4, “Transport and storage of unmounted specimens” . 6
9 Modification to Clause 7.6 “Storage” . 6
10 Modification to Clause 8.2.3, “Execution of test” . 6
11 Modification to Clause 8.3.4, “Procedure A” . 7
12 Modification to Clause 9.1.1, “Calculation of the proportional rut depth” . 7
13 Modification to Clause 9.1.2, “Graph” .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.