SIST EN 14894:2011
(Main)LPG equipment and accessories - Cylinder and drum marking
LPG equipment and accessories - Cylinder and drum marking
This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including:
- Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority.
- LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority.
- Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority.
- LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority.
NOTE All these types of receptacles are referred to throughout this standard as "cylinders".
This standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements.
Flüssiggas-Geräte und Ausrüstungsteile - Kennzeichnung von Flaschen und Fässern
Diese Europäische Norm legt Anforderungen an die Stempelung von ortsbeweglichen wiederbefüllbaren Flaschen und metallischen Fässern für Flüssiggas (LPG; en: Liquefied Petroleum Gas) fest, einschließlich:
- LPG-Flaschen aus Stahl, ausgelegt und hergestellt in Übereinstimmung mit EN 1442, EN 14140, EN 12807 oder einer gleichwertigen Norm oder von der zuständigen Behörde anerkannten technischen Vorschrift;
- metallischer LPG-Fässer, ausgelegt und hergestellt in Übereinstimmung mit EN 14893 oder einer gleichwertigen Norm oder von der zuständigen Behörde anerkannten technischen Vorschrift;
- geschweißter LPG-Flaschen aus Aluminium, ausgelegt und hergestellt in Übereinstimmung mit EN 13110 oder einer gleichwertigen Norm oder von der zuständigen Behörde anerkannten technischen Vorschrift;
- LPG-Flaschen aus Verbundwerkstoffen, ausgelegt und hergestellt in Übereinstimmung mit EN 14427 oder einer gleichwertigen Norm oder von der zuständigen Behörde anerkannten technischen Vorschrift.
ANMERKUNG Alle diese Gefäßarten werden in der gesamten vorliegenden Norm als „Flaschen“ bezeichnet.
Diese Norm legt keinerlei Anforderungen an die Produkt-, Gefährdungs- oder sicherheitsrelevante Verpackungskennzeichnung fest, die zur Erfüllung der ADR- oder anderer gesetzlicher Anforderungen erforderlich sein können.
Équipements pour gaz de pétrole liquéfié et leurs accessoires - Marquage des bouteilles et des fûts à pression
La présente Norme européenne prescrit les exigences de marquage s'appliquant aux bouteilles à GPL
transportables rechargeables et aux fûts à pression métalliques, incluant :
- les bouteilles à GPL en acier conçues et fabriquées conformément aux normes EN 1442, EN 14140,
EN 12807 ou à une norme équivalente ou un code technique reconnu par l'autorité compétente ;
- les fûts à pression métalliques pour GPL conçus et fabriqués conformément à l'EN 14893 ou à une
norme équivalente ou un code technique reconnu par l'autorité compétente ;
- les bouteilles à GPL en aluminium soudées, conçues et fabriquées conformément à l'EN 13110 ou à une
norme équivalente ou un code technique reconnu par l'autorité compétente ;
- les bouteilles à GPL en matériaux composites conçues et fabriquées conformément à l'EN 14427 ou à
une norme équivalente ou un code technique reconnu par l'autorité compétente.
NOTE Dans la présente norme, tous ces types de récipients sont désignés "bouteilles".
La présente norme ne prescrit pas d'exigences relatives au produit, aux phénomènes dangereux ou à
l'étiquetage de sécurité de l'emballage, pouvant être requises pour la conformité à l'ADR ou à toute autre
exigence législative.
Oprema in pribor za utekočinjeni naftni plin (UNP) - Označevanje jeklenk in sodov
Ta evropski standard določa zahteve za označevanje z žigom za prenosne jeklenke in kovinske sode za utekočinjeni naftni plin za večkratno polnjenje, ki vključujejo: - jeklene jeklenke za utekočinjeni naftni plin, načrtovane in izdelane v skladu z EN 1442, EN 14140, EN 12807 ali enakovrednim standardom ali tehničnim kodeksom, ki ga priznava pristojni organ; - kovinske sode za utekočinjeni naftni plin, načrtovane in izdelane v skladu z EN 14893 ali enakovrednim standardom ali tehničnim kodeksom, ki ga priznava pristojni organ; - varjene aluminijaste jeklenke za utekočinjeni naftni plin, načrtovane in izdelane v skladu z EN 13110 ali enakovrednim standardom ali tehničnim kodeksom, ki ga priznava pristojni organ; - kompozitne jeklenke za utekočinjeni naftni plin, načrtovane in izdelane v skladu z EN 14427 ali enakovrednim standardom ali tehničnim kodeksom, ki ga priznava pristojni organ.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flüssiggas-Geräte und Ausrüstungsteile - Kennzeichnung von Flaschen und FässernÉquipements pour gaz de pétrole liquéfié et leurs accessoires - Marquage des bouteilles et des fûts à pressionLPG equipment and accessories - Cylinder and drum marking23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 14894:2011SIST EN 14894:2011en,fr,de01-november-2011SIST EN 14894:2011SLOVENSKI
STANDARDSIST EN 14894:20061DGRPHãþD
SIST EN 14894:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14894
May 2011 ICS 23.020.30 Supersedes EN 14894:2006English Version
LPG equipment and accessories - Cylinder and drum marking
Equipements pour gaz de pétrole liquéfié - Marquage des bouteilles et des fûts à pression
Flüssiggas-Geräte und Ausrüstungsteile - Kennzeichnung von Flaschen und Fässern This European Standard was approved by CEN on 24 March 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14894:2011: ESIST EN 14894:2011
EN 14894:2011 (E) 2 Contents Page Foreword .3Introduction .41 Scope .52 Terms and definitions .53 Symbols and abbreviations .54 Application of stamp markings .64.1 General .64.2 Workmanship .64.3 Arrangements for stamp marking .75 Manufacturing stamp markings .76 Operational stamp markings .87 Certification stamp markings .98 Other stamp markings .9Annex A (informative)
Examples of alternative locations, stamp markings . 12Bibliography . 13 SIST EN 14894:2011
EN 14894:2011 (E) 3 Foreword This document (EN 14894:2011) has been prepared by Technical Committee CEN/TC 286 “Liquefied petroleum gas equipment and accessories”, the secretariat of which is held by NSAI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2011, and conflicting national standards shall be withdrawn at the latest by November 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14894:2006. The main technical change to this standard is to align the marking requirements with ADR/RID 2011 (see [7] and [8]). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 14894:2011
EN 14894:2011 (E) 4 Introduction This European Standard calls for the use of substances and procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage. It has been assumed in the drafting of this European Standard that the execution of its provisions is entrusted to appropriately qualified and experienced people. SIST EN 14894:2011
EN 14894:2011 (E) 5 1 Scope This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including: Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority. LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority. Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority. LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority. NOTE All these types of receptacles are referred to throughout this standard as “cylinders”. This standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements. 2 Terms and definitions For the purposes of this document, the following terms and definitions applies. 2.1 liquefied petroleum gas LPG one or more light hydrocarbons which are assigned to UN 1011, UN 1075, UN 1965, UN 1969 or UN 1978 only and which consists mainly of propane, propene, butane, butane isomers, butene or traces of other hydrocarbon gases. 2.2 stamp marking permanent or durable markings affixed to the cylinder 2.3 competent authority authority designated as such in each country in accordance with national regulation 2.4 inspection body independent inspection and testing body approved by the competent authority 3 Symbols and abbreviations TPED: Transportable Pressure Equipment Directive
SIST EN 14894:2011
EN 14894:2011 (E) 6 4 Application of stamp markings 4.1 General 4.1.1 Stamp markings consist of manufacturing, operational and certification stamp marks and are listed in Clause 5, Clause 6, Clause 7 and Clause 8. The layout of the marks is covered by 4.3. Additional markings may be applied if required by other regulations or technical standards, or when required by the cylinder owner; provided the layout does not cause any confusion in their interpretation and the clarity of the other mandatory markings is not affected. 4.1.2 Low stress stamp marking methods shall be utilised. 4.1.3 Stamp markings shall be applied to low stress areas. 4.1.4 Stamp marking shall be in accordance with the requirements of the current version of ADR/RID and with EN 14894. The requirements of ADR/RID shall override conflicting requirements of this standard. NOTE 1 This may lead to temporary noncompliance with EN 14894. NOTE 2 The TPED includes additional marking requirements (“” marking). 4.2 Workmanship 4.2.1 All stamp markings shall be affixed clearly, legibly and durably on the cylinder and shall remain legible under all foreseeable operating and ageing conditions.
Markings required to be “permanent” shall be such that they can only be removed with the use of special tools and may be done, for example by hard metal stamping, engraving, casting, embossing, encapsulation or other similar methods. Markings required to be “durable” shall be such that they remain visible for the relevant period of time and may be done, for example by printing, external labelling, stencilling, use of valve hand-wheel insert or other similar methods.
Clause 5, Clause 6, Clause 7 and Clause 8 indicate which markings shall be "permanent (P)" and which may be "durable (D)". NOTE Markings which are permitted to be durable may be permanently applied if so desired. 4.2.2 For metallic cylinders, the markings shall be located on the shoulder, top end or neck of the cylinder or on a permanently affixed component, e.g. shroud, handle(s), foot ring, welded nameplate, etc.
4.2.3 If markings are applied after completion of manufacture
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flüssiggas-Geräte und Ausrüstungsteile - Kennzeichnung von Flaschen und FässernÉquipements pour gaz de pétrole liquéfié et leurs accessoires - Marquage des bouteilles et des fûts à pressionLPG equipment and accessories - Cylinder and drum marking23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:FprEN 14894kSIST FprEN 14894:2010en,de01-november-2010kSIST FprEN 14894:2010SLOVENSKI
STANDARD
kSIST FprEN 14894:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN 14894
September 2010 ICS 23.020.30 Will supersede EN 14894:2006English Version
LPG equipment and accessories - Cylinder and drum marking
Équipements pour gaz de pétrole liquéfié et leurs accessoires - Marquage des bouteilles et des fûts à pression
Flüssiggas-Geräte und Ausrüstungsteile - Kennzeichnung von Flaschen und Fässern This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 286.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN 14894:2010: EkSIST FprEN 14894:2010
FprEN 14894:2010 (E) 2 Contents Page Foreword .3Introduction .41 Scope .52 Terms and definitions .53 Symbols and abbreviations .54 Application of stamp markings .54.1 General .54.2 Workmanship .64.3 Arrangements for stamp marking .65 Manufacturing stamp markings .76 Operational stamp markings .77 Certification stamp markings .88 Other stamp markings .8Annex A (informative)
Examples of alternative locations, stamp markings . 11Bibliography . 12 kSIST FprEN 14894:2010
FprEN 14894:2010 (E) 3 Foreword This document (FprEN 14894:2010) has been prepared by Technical Committee CEN/TC 286 “LPG equipment and accessories”, the secretariat of which is held by NSAI. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 14894:2006. The main technical change to this standard is to align the marking requirements with ADR/RID 2011 (see [7] and [8]). kSIST FprEN 14894:2010
FprEN 14894:2010 (E) 4 Introduction This European Standard calls for the use of substances and procedures that may be injurious to health if adequate precautions are not taken. It refers only to technical suitability and does not absolve the user from legal obligations relating to health and safety at any stage. It has been assumed in the drafting of this European Standard that the execution of its provisions is entrusted to appropriately qualified and experienced people. kSIST FprEN 14894:2010
FprEN 14894:2010 (E) 5 1 Scope This European Standard specifies stamp marking requirements for transportable refillable LPG cylinders and metallic drums including: Steel LPG cylinders designed and manufactured in accordance with EN 1442, EN 14140, EN 12807 or an equivalent standard or technical code recognised by the Competent Authority. LPG metallic drums designed and manufactured in accordance with EN 14893 or an equivalent standard or technical code recognised by the Competent Authority. Welded aluminium LPG cylinders designed and manufactured in accordance with EN 13110 or an equivalent standard or technical code recognised by the Competent Authority. LPG composite cylinders designed and manufactured in accordance with EN 14427 or an equivalent standard or technical code recognised by the Competent Authority. NOTE All these types of receptacles are referred to throughout this standard as “cylinders”. This standard does not specify any requirements for product, hazard or safety-phrase labelling of packaging which may be required to meet ADR or other legislative requirements. 2 Terms and definitions For the purposes of this document, the following term and definition applies. 2.1 LPG (liquefied petroleum gas) mixture of predominantly butane or propane with traces of other hydrocarbon gases classified in accordance with UN number 1965, hydrocarbon gases mixture, liquefied, NOS or UN number 1075, petroleum gases, liquefied NOTE In some countries, UN number 1011, 1978 may also be designated LPG. 2.2 stamp marking permanent or durable markings affixed to the cylinder 3 Symbols and abbreviations TPED: Directive 2010/35/EU of the European Parliament and of the Council of 16 June 2010 on transportable pressure equipment TDG-Model regulations: UN Recommendations on the Transport Of Dangerous Goods Model Regulations 4 Application of stamp markings 4.1 General 4.4.1 Stamp markings consist of manufacturing, operational and certification stamp marks and are listed in Clause 5, Clause 6, Clause 7 and Clause 8. The layout of the marks is covered by 4.3. Additional markings may be applied if required by other regulations or technical standards, or when required by the cylinder owner; kSIST FprEN 14894:2010
FprEN 14894:2010 (E) 6 provided the layout does not cause any confusion in their interpretation and the clarity of the other mandatory markings is not affected. 4.1.2 Low stress stamp marking methods shall be utilised. 4.1.3 Stamp markings shall be applied to low stress areas. 4.1.4 Stamp marking shall be in accordance with the requirements of the current version of ADR/RID and with EN 14894. The requirements of ADR/RID shall override conflicting requirements of this standard. NOTE 1 This may lead to temporary noncompliance with EN 14894. NOTE 2 The TPED includes additional marking requirements (“” marking). 4.2 Workmanship 4.2.1 All stamp markings shall be affixed clearly, legibly and durably on the cylinder and shall remain legible under all foreseeable operating and ageing conditions.
Markings required to be “permanent” shall be such that they can only be removed with the use of special tools and may be done, for example by hard metal stamping, engraving, casting, embossing, encapsulation or other similar methods. Markings required to be “durable” shall be such that they remain visible for the relevant period of time and may be done, for example by printing, external labelling, stencilling, use of valve hand-wheel insert or other similar methods.
Clause 5, Clause 6, Clause 7 and Clause 8 indicate which markings shall be "permanent (P)" and which may be "durable (D)". NOTE Markings which are permitted to be durable may be permanently applied if so desired. 4.2.2 For metallic cylinders, the markings shall be located on the shoulder, top end or neck of the cylinder or on a permanently affixed component, e.g. welded nameplate, handle(s), foot ring, shroud etc.
4.2.3 If markings are applied after completion of manufacture or following periodic inspectio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.