SIST EN ISO 1307:2009

Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006)

This International Standard specifies the sizes of rubber and plastics hoses and the minimum and maximum inside diameters permitted for each hose size. For this purpose, hoses are divided into four types according to the process by which they are manufactured. The standard also specifies tolerances on cut-to-length rubber and plastics hoses for industrial and automotive applications. This standard is intended to be used with the relevant hoses product standard unless there is justification for using a different hose size or unless a hose size needs a different inside-diameter range for a particular application.

Gummi- und Kunststoffschläuche - Schlauchmaße, Kleinst- und Größt-Innendurchmesser, und Toleranzen bei abgelängten Schläuchen (ISO 1307:2006)

Diese Internationale Norm legt die Maße von Gummi- und Kunststoffschläuchen und die zulässigen Kleinst- und Größtinnendurchmesser für jedes Schlauchmaß fest. Für diesen Zweck, werden Schläuche in vier Typen aufgeteilt in Anlehnung an den Fertigungsprozess ihrer Herstellung. Die Norm legt weiterhin die Toleranzen für abgelängte Gummi- und Kunststoffschläuche für Industrie- und Kraftfahrzeuganwendungen fest. Diese Norm ist gedacht für den Einsatz mit den entsprechenden Schlauchproduktnormen, sofern nicht eine Begründung für den Gebrauch eines abweichenden Schlauchmaßes vorliegt oder denn für eine besondere Anwendung ein Schlauchmaß mit einem anderen Innendurchmesserbereich benötigt wird.

Tuyaux en caoutchouc et en plastique - Diametres nominaux, diametres intérieurs minimaux et maximaux, et tolérances sur la longueur de coupe (ISO 1307:2006)

L'ISO 1307:2006 spécifie les dimensions des tuyaux en caoutchouc et en plastique ainsi que les diamètres intérieurs minimaux et maximaux autorisés pour chaque dimension de tuyau. À cet effet, les tuyaux sont divisés en quatre types en fonction de leur procédé de fabrication. La présente norme spécifie également les tolérances sur la longueur de coupe des tuyaux en caoutchouc et en plastique destinés aux applications industrielles et automobiles. Sauf justification relative à l'utilisation d'une dimension différente ou à moins qu'un diamètre nominal nécessite une gamme de diamètres intérieurs différente pour une application particulière, la présente norme est destinée à être utilisée conjointement avec la norme de produit correspondante relative aux tuyaux.

Gumene in polimerne cevi - Velikosti cevi, najmanjši in največji notranji premeri in tolerance dolžin (ISO 1307:2006)

General Information

• Status: Published
• Publication Date: 11-Dec-2008
• ICS: 23.040.70 - Hoses and hose assemblies
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Dec-2008
• Due Date: 09-Feb-2009
• Completion Date: 12-Dec-2008
• Ref Project: EN ISO 1307:2008 - Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006)

Relations

• Replaces: SIST EN ISO 1307:2000 - Rubber and plastics hoses for general-purpose industrial applications - Bore diameters and tolerances, and tolerances on length (ISO 1307:1992)
• Effective Date: 01-Feb-2009

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 1307:2009
01-februar-2009
1DGRPHãþD
SIST EN ISO 1307:2000
*XPHQHLQSROLPHUQHFHYL9HOLNRVWLFHYLQDMPDQMãLLQQDMYHþMLQRWUDQMLSUHPHULLQ
WROHUDQFHGROåLQ,62
Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and
tolerances on cut-to-length hoses (ISO 1307:2006)
Gummi- und Kunststoffschläuche - Schlauchmaße, Kleinst- und Größt-
Innendurchmesser, und Toleranzen bei abgelängten Schläuchen (ISO 1307:2006)
Tuyaux en caoutchouc et en plastique - Diametres nominaux, diametres intérieurs
minimaux et maximaux, et tolérances sur la longueur de coupe (ISO 1307:2006)
Ta slovenski standard je istoveten z: EN ISO 1307:2008
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 1307:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 1307:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 1307:2009
EUROPEAN STANDARD
EN ISO 1307
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2008
ICS 23.040.70 Supersedes EN ISO 1307:1995
English Version
Rubber and plastics hoses - Hose sizes, minimum and
maximum inside diameters, and tolerances on cut-to-length
hoses (ISO 1307:2006)
Tuyaux en caoutchouc et en plastique - Dimensions des Gummi- und Kunststoffschläuche - Schlauchmaße, Kleinst-
tuyaux, diamètres intérieurs minimaux et maximaux, et und Größt-Innendurchmesser, und Toleranzen bei
tolérances sur la longueur de coupe (ISO 1307:2006) abgelängten Schläuchen (ISO 1307:2006)
This European Standard was approved by CEN on 26 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1307:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 1307:2009
EN ISO 1307:2008 (E)






Foreword



The text of ISO 1307:2006 has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 1307:2008 by Technical Committee CEN/TC 218 "Rubber and plastics hoses
and hose assemblies", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by July 2008, and conflicting national standards
shall be withdrawn at the latest by July 2008.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any
or all such patent rights.
This document supersedes EN ISO 1307:1995.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United
Kingdom.

Endorsement notice

The text of ISO 1307:2006 has been approved by CEN as EN ISO 1307:2008 without any
modifications.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 1307:2009


INTERNATIONAL ISO
STANDARD 1307
Fourth edition
2006-09-15

Rubber and plastics hoses — Hose sizes,
minimum and maximum inside diameters,
and tolerances on cut-to-length hoses
Tuyaux en caoutchouc et en plastique — Diamètres nominaux,
diamètres intérieurs minimaux et maximaux, et tolérances sur la
longueur de coupe




Reference number
ISO 1307:2006(E)
©
ISO 2006

---------------------- Page: 5 ----------------------

SIST EN ISO 1307:2009
ISO 1307:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or
...