Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes

This Part of EN 13244 specifies the characteristics of pipes made from polyethylene (PE) intended to be used in the field of buried and above-ground pressure systems for water for general purposes, drainage and sewerage. It also specifies the test parameters for the test methods referred to in this standard.

Kunstoff-Rohrleitungssysteme für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser - Polyethylen (PE) - Teil 2: Rohre

Dieser Teil von EN 13244 legt die Anforderungen an Rohre aus Polyethylen (PE) fest, die für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser eingesetzt werden. Er gilt auch für Vakuum-Abwassersysteme.
ANMERKUNG 1   Brauchwasser ist nicht für den menschlichen Gebrauch bestimmt und Rohrleitungsteile, die dieser Norm entsprechen, sollten nicht für die Wasserversorgung für den menschlichen Gebrauch verwendet werden. Rohrleitungsteile aus PE für die Verwendung in der Wasserversorgung für den menschlichen Gebrauch und die Fortleitung von Rohwasser, das zur Aufbereitung von Trinkwasser genutzt wird, siehe EN 12201.
Er legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird.
Zusammen mit den übrigen Teilen der EN 13244 (siehe Vorwort) gilt dieser Teil für Rohre aus PE, deren Verbindungen untereinander sowie mit Rohrleitungsteilen aus anderen Werkstoffen, die zur Verwendung unter den folgenden Bedingungen vorgesehen sind:
   Verlegung im Rohrgraben;
   Entwässerung ins Meer (Siele);
   Überlandleitungen in Binnengewässern und Kanälen;
   Düker und Brückenleitungen;
   der maximal zulässige Betriebsdruck MOP beträgt nicht mehr als 25 bar  ;
   es gilt eine Betriebstemperatur von 20 °C als Bezugstemperatur.
ANMERKUNG 2   Für Anwendungsgebiete, in denen konstante Betriebstemperaturen über 20 °C bis maximal 40 °C auftreten, siehe Anhang A, EN 13244-1:2002.
EN 13244 enthält Festlegungen über maximal zulässige Betriebsdrücke und legt Anforderungen an die Einfärbung von Rohrleitungsteilen sowie die Verwendung von Zusatzstoffen fest.
ANMERKUNG 3   Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Empfehlungen oder Festlegungen und Verlegepraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.
ANMERKUNG 4   Die Bestimmung des Widerstandes gegen langsames Risswachstum von PE-Formmassen, die für die Herstellung von Rohren nac

Systemes de canalisations en plastique pour les applications générales de transport d'eau, de branchement et de collecteurs d'assainissement, enterrés sous pression - Polyéthylene (PE) - Partie 2: Tubes

La présente partie de l'EN 13244 spécifie les aspects généraux des systemes de canalisations en polyéthylene pour les applications générales de transport d'eau, de branchements et de collecteurs d'assainissement enterrés et aériens sous pression. Elle s'applique aussi aux systemes de collecteurs par le vide.
NOTE 1   L'eau pour les applications générales n'est pas destinée a  la consommation humaine et il convient que les composants conformes a cette norme ne soient utilisés pour des systemes de transport d'eau pour la consommation humaine. Pour les composants PE destinés au transport de l'eau pour la consommation humaine y compris les eaux brutes avant traitement , voir l'EN 12201.
Elle spécifie également les parametres d'essai pour les méthodes d'essai auxquelles il est fait référence dans la présente norme.
Conjointement aux autres parties de l'EN 13244 (voir avant-propos), elle s'applique aux tubes en PE, a leurs assemblages et aux assemblages avec des composants en PE et d'autres matieres destinés a etre utilisés selon les conditions suivantes :
   enterrés dans le sol ;
   déversoirs en mer ;
   posés dans l'eau ;
   au dessus du sol, y compris les tubes suspendus sous les ponts ;
   a une pression de service maximale, MOP, pouvant atteindre jusqu'a 25 bar ) ;
   a une température de service de 20 °C comme température de référence.
NOTE 2   Pour des applications fonctionnant a des températures constantes supérieures a 20 °C et jusqu'a 40 °C voir l'Annexe A de l'EN 13244-1:2002.
L'EN 13244 comprend une gamme étendue de pressions de service et spécifie les exigences concernant les couleurs et les additifs.
NOTE 3   Il est de la responsabilité de l'acheteur ou du prescripteur d'effectuer le choix approprié de ces aspects, prenant en compte les exigences particulieres et les regles nationales correspondantes ainsi que les pratiques ou les codes de pose.
NOTE 4   L'évaluation de la résistance a la fissuration lente des composants d'un tube en PE utilisés pour la fa

Cevni sistemi iz polimernih materialov, podzemni in nadzemni, za tlačne vodovode splošne namembnosti, odvodnjavanje in kanalizacijo – Polietilen (PE) - 2. del: Cevi

General Information

Status
Withdrawn
Publication Date
30-Sep-2003
Withdrawal Date
07-Nov-2011
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
08-Nov-2011
Due Date
01-Dec-2011
Completion Date
08-Nov-2011

Relations

Buy Standard

Standard
EN 13244-2:2003
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunstoff-Rohrleitungssysteme für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser - Polyethylen (PE) - Teil 2: RohreSystemes de canalisations en plastique pour les applications générales de transport d'eau, de branchement et de collecteurs d'assainissement, enterrés sous pression - Polyéthylene (PE) - Partie 2: TubesPlastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 2: Pipes93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.20Cevi iz polimernih materialovPlastics pipesICS:Ta slovenski standard je istoveten z:EN 13244-2:2002SIST EN 13244-2:2003en01-oktober-2003SIST EN 13244-2:2003SLOVENSKI
STANDARD



SIST EN 13244-2:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13244-2December 2002ICS 23.040.20; 93.030English versionPlastics piping systems for buried and above-ground pressuresystems for water for general purposes, drainage and sewerage- Polyethylene (PE) - Part 2: PipesSystèmes de canalisations en plastique pour lesapplications générales de transport d'eau, de branchementet de collecteurs d'assainissement, enterrés sous pression- Polyéthylène (PE) - Partie 2: TubesKunstoff-Rohrleitungssysteme für erd- und oberirdischverlegte Druckrohrleitungen für Brauchwasser,Entwässerung und Abwasser - Polyethylen (PE) - Teil 2:RohreThis European Standard was approved by CEN on 23 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13244-2:2002 ESIST EN 13244-2:2003



EN 13244-2:2002 (E)2ContentspageForeword.3Introduction.51Scope.62Normative references.63Definitions, symbols and abbreviations.74Material.74.1Compound.74.2Identification compound.75General characteristics.75.1Appearance.75.2Colour.76Geometrical characteristics.86.1Measurement of dimensions.86.2Mean outside diameters and out-of-roundness (ovality).86.3Wall thicknesses and their tolerances.96.4Coiled pipe.126.5Pipe lengths.126.6Pipe stiffness.127Mechanical characteristics.127.1Conditioning.127.2Requirements.127.3Retest in case of failure at 80 °C.138Physical characteristics.148.1Conditioning.148.2Requirements.149Chemical characteristics of pipes in contact with chemicals.1510Performance requirements.1511Marking.1511.1General.1511.2Minimum required marking of pipes.16Annex A (informative)
Relationship between PN, MRS, S and SDR.17Annex B (normative)
Pipe stiffness.18Bibliography.19SIST EN 13244-2:2003



EN 13244-2:2002 (E)3ForewordThis document (EN 13244-2:2002) has been prepared by Technical Committee CEN/TC 155 "Plastics pipingsystems and ducting systems", the secretariat of which is held by NEN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2003, and conflicting national standards shall be withdrawn at the latest byDecember 2004.For components which have conformed to the relevant national standard before December 2002, as shown by themanufacturer or by a certification body, the national standard may continue to be applied until December 2004.It has been prepared in liaison with CEN/TC 165 "Waste water engineering".This European Standard is a Part of a System Standard for plastics piping systems of a particular material for aspecified application. There are a number of such System Standards.System Standards are based on the results of the work being undertaken in ISO/TC 138 "Plastics pipes, fittingsand valves for the transport of fluids", which is a Technical Committee of the International Organization forStandardization (ISO).They are supported by separate standards on test methods to which references are made throughout the SystemStandard.The System Standards are consistent with standards on general functional requirements and standards onrecommended practices for installation.EN 13244 consists of the following Parts, under the general title Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage — Polyethylene (PE):— Part 1: General— Part 2: Pipes (this standard)— Part 3: Fittings— Part 4: Valves— Part 5: Fitness for purpose of the system— Part 7: Guidance for the assessment of conformity (to be published as a CEN/TS)NOTEIt was decided not to publish a Part 6: Recommended practice for installation. Instead, existing national practiceswould be applicable.This Part of EN 13244 includes the following:— Annex A (informative): Relationship between PN, MRS, S and SDR— Annex B (normative): Pipe stiffness— BibliographySystem Standards for piping systems of other plastics materials used for the conveyance of water, drainage andsewerage under pressure include the following:prEN 14364,
Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforcedthermosetting (GRP) plastics based on polyester resin (UP).SIST EN 13244-2:2003



EN 13244-2:2002 (E)4EN 1456,
Plastics piping systems for buried and above-ground drainage and sewerage under pressure —Unplasticized poly(vinyl chloride) (PVC-U).According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 13244-2:2003



EN 13244-2:2002 (E)5IntroductionEN 13244, of which this is Part 2, specifies the requirements for a piping system and its components when madefrom polyethylene (PE), intended to be used for buried and above-ground pressure systems for water for generalpurposes, drainage and sewerage, including vacuum systems.Requirements and test methods for material and components, other than pipes, are specified in EN 13244-1, EN13244-3 and EN 13244-4. Characteristics for fitness for purpose are covered in EN 13244-5 and prCEN/TS 13244-7 gives guidance for the assessment of conformity.This Part of EN 13244 covers the characteristics of pipes.SIST EN 13244-2:2003



EN 13244-2:2002 (E)61 ScopeThis Part of EN 13244 specifies the characteristics of pipes made from polyethylene (PE) intended for buried andabove-ground pressure systems for water for general purposes, drainage and sewerage. It is also applicable forvacuum sewer systems.NOTE 1Water for general purposes is not intended for human consumption and components conforming to this standardshould not be used in systems conveying water for human consumption. For PE components intended for the conveyance ofwater intended for human consumption and raw water prior to treatment, see EN 12201.It also specifies the test parameters for the test methods referred to in this standard.In conjunction with other Parts of EN 13244 (see Foreword), it is applicable to PE pipes, their joints and to jointswith components of PE and other materials intended to be used as follows:¾ buried in the ground;¾ sea outfalls;¾ laid in water;¾ above-ground, including pipes suspended below bridges;¾ a maximum operating pressure, MOP, up to and including 25 bar 1);¾ an operating temperature of 20 °C as a reference temperature.NOTE 2For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see annex A of EN 13244-1:2002.EN 13244 covers a range of maximum operating pressures and gives requirements concerning colours andadditives.NOTE 3It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking intoaccount their particular requirements and any relevant national guidance or regulations and installation practices or codes.NOTE 4Assessment of the resistance to slow crack growth of the PE pipe compound used for the manufacture of productsto this specification is required in accordance with Table 2 of EN 13244-1:2002.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 728,
Plastics piping and ducting systems — Polyolefin pipes and fittings — Determination of oxidationinduction time.EN 921:1994,
Plastics piping systems — Thermoplastics pipes — Determination of resistance to internal pressureat constant temperature.EN 13244-1:2002,
Plastics piping systems for buried and above-ground pressure systems for water for generalpurposes, drainage and sewerage — Polyethylene (PE) — Part 1: General.
1)
1 bar = 105 N/m2 .SIST EN 13244-2:2003



EN 13244-2:2002 (E)7EN 13244-5:2002,
Plastics piping systems for buried and above-ground pressure systems for water for generalpurposes, drainage and sewerage — Polyethylene (PE) — Part 5: Fitness for purpose of the system.EN ISO 1133:1999,
Plastics — Determination of the melt-mass flow rate (MFR) and the melt-volume flow rate(MVR) of thermoplastics (ISO 1133:1997).prEN ISO 3126:1999,
Plastics piping systems — Plastics piping components — Measurement and determinationof dimensions (revision of prEN 496:1991 and ISO 3126:1974) (ISO/DIS 3126:1999).EN ISO 6259-1:2001,
Thermoplastics pipes — Determination of tensile properties — Part 1: General test method(ISO 6259-1:1997).ISO 4433-1:1997,
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersiontest method.ISO 4433-2:1997,
Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefinpipes.ISO 6259-3:1997,
Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes.3 Definitions, symbols and abbreviationsFor the purposes of this European Standard the terms, definitions, symbols and abbreviations given inEN 13244-1 apply.4 Material4.1 CompoundThe material from which the pipes are made shall conform to EN 13244-1.4.2 Identification compoundWhere applicable, the compound used for identification stripes (see 5.2) shall be made from a PE polymermanufactured from the same type of base polymer as used in the compound for pipe production.5 General characteristics5.1 AppearanceWhen viewed without magnification the internal and external surfaces of pipes shall be smooth, clean and free fromscoring, cavities, and other surface defects to an extent that would prevent conformity of the pipe to this standard.The pipe ends shall be cut cleanly and square to the axis of the pipe.5.2 ColourThe pipes shall be black or black with brown stripes unless other colours or forms of identification are specified bynational regulations.NOTE 1Where national regulations require an alternative colour to black, pipes coloured blue or black with blue stripesshould not be used for this application. The blue colour indicates that the components are suitable for the conveyance of waterintended for human consumption as specified in EN 12201[1].NOTE 2For above ground installations non-black pipes should be protected
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.