SIST EN ISO 11623:2016
(Main)Gas cylinders - Composite construction - Periodic inspection and testing (ISO 11623:2015)
Gas cylinders - Composite construction - Periodic inspection and testing (ISO 11623:2015)
This International Standard specifies the requirements for periodic inspection and testing and to verify
the integrity for further service of hoop-wrapped and fully-wrapped composite transportable gas
cylinders, with aluminium-alloy, steel or non-metallic liners or of linerless construction (Types 2, 3, 4,
and 5), intended for compressed, liquefied or dissolved gases under pressure, of water capacity from
0,5 l up to 450 l.
This International Standard is written to address the periodic inspection and testing of composite
cylinders constructed to ISO 11119-1, ISO 11119-2, and ISO 11119-3 standards and can be applied to other
composite cylinders designed to comparable standards when authorized by the competent authority.
As far as practicable, this International Standard also can be applied to cylinders of less than 0,5 l
water capacity.
Gasflaschen - Verbundbauweise - Wiederkehrende Inspektion und Prüfung (ISO 11623:2015)
Diese Internationale Norm legt die Anforderungen an die wiederkehrende Inspektion und Prüfung von umfangs- und vollumwickelten ortsbeweglichen Gasflaschen aus Verbundwerkstoffen (Composite-Flaschen) mit Linern aus Aluminiumlegierungen, Stahl oder nichtmetallischen Werkstoffen oder Flaschenbauweisen ohne Liner mit einem Fassungsraum von 0,5 l bis 450 l fest, welche zur Verwendung mit verdichteten, verflüssigten oder unter Druck gelösten Gasen vorgesehen sind.
Diese Norm wurde geschrieben, um die wiederkehrende Inspektion und Prüfung von nach ISO 11119-1, ISO 11119-2 und ISO 11119-3 ausgelegten Composite-Flaschen zu beschreiben und darf mit Genehmigung der zuständigen Behörde auch für nach vergleichbaren Normen ausgelegte Composite-Flaschen angewendet werden.
Soweit möglich, darf diese Internationale Norm auch für Flaschen mit einem Fassungsraum kleiner als 0,5 l angewendet werden.
Diese Internationale Norm legt die Anforderungen an die wiederkehrende Inspektion und Prüfung fest, um die Unversehrtheit solcher Gasflaschen für den weiteren Betrieb zu überprüfen.
Bouteilles à gaz transportables - Contrôles et essais périodiques des bouteilles à gaz en matériau composite (ISO 11623:2015)
ISO 11623:2015 spécifie les exigences relatives au contrôle et essais périodiques des bouteilles à gaz en matériau composite transportables, frettées ou entièrement bobinées, dotées ou non d'un liner en alliage d'aluminium, en acier ou non-métallique (Types 2, 3, 4, et 5), destinées à contenir des gaz comprimés, liquéfiés ou dissous sous pression et ayant une capacité en eau comprise entre 0,5 l et 450 l inclus, ainsi que la vérification de leur intégrité pour leur maintien en service.
ISO 11623:2015 est élaborée afin de couvrir les contrôles et essais périodiques des bouteilles gaz en matériau composite construites conformément aux normes ISO 11119‑1, ISO 11119‑2, et ISO 11119‑3 et peut être étendue à d'autres bouteilles en matériau composite conçues conformément à des normes comparables lorsque l'autorité compétente l'autorise.
Dans la mesure du possible, la présente Norme internationale peut également être appliquée aux bouteilles ayant une capacité inférieure à 0,5 l.
Plinske jeklenke - Kompozitni materiali - Periodični pregledi in preskusi (ISO 11623:2015)
Ta mednarodni standard opredeljuje zahteve za periodične preglede in preskuse ter preverjanje celovitosti za namen nadaljnje uporabe premičnih jeklenk za plin, obročasto in popolnoma obvitih s kompozitno maso, s tuljavami iz aluminijeve zlitine, jekla ali materiala, ki ni kovina, ali s konstrukcijo brez tuljav (tipi 2, 3, 4 in 5), ki so namenjeni za stisnjene, utekočinjene ali raztopljene pline pod tlakom, s prostornino vode od 0,5 do 450 l.
Ta mednarodni standard obravnava periodične preglede in preskuse kompozitnih jeklenk, izdelanih v skladu s standardi ISO 11119-1, ISO 11119-2 in ISO 11119-3, pri čemer ga je mogoče uporabiti za druge kompozitne jeklenke, zasnovane v skladu s primerljivimi standardi, če to odobri pristojni organ. V smislu praktičnosti je mogoče ta mednarodni standard uporabiti za jeklenke s prostornino vode, manjšo od 0,5 l.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11623:2016
01-marec-2016
1DGRPHãþD
SIST EN ISO 11623:2002
3OLQVNHMHNOHQNH.RPSR]LWQLPDWHULDOL3HULRGLþQLSUHJOHGLLQSUHVNXVL ,62
Gas cylinders - Composite construction - Periodic inspection and testing (ISO
11623:2015)
Gasflaschen - Verbundbauweise - Wiederkehrende Inspektion und Prüfung (ISO
11623:2015)
Bouteilles à gaz transportables - Contrôles et essais périodiques des bouteilles à gaz en
matériau composite (ISO 11623:2015)
Ta slovenski standard je istoveten z: EN ISO 11623:2015
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
SIST EN ISO 11623:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11623:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 11623:2016
EN ISO 11623
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2015
EUROPÄISCHE NORM
ICS 23.020.30 Supersedes EN ISO 11623:2002
English Version
Gas cylinders - Composite construction - Periodic
inspection and testing (ISO 11623:2015)
Bouteilles à gaz - Construction composite - Contrôles et Gasflaschen - Verbundbauweise - Wiederkehrende
essais périodiques (ISO 11623:2015) Inspektion und Prüfung (ISO 11623:2015)
This European Standard was approved by CEN on 3 October 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11623:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11623:2016
EN ISO 11623:2015 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11623:2016
EN ISO 11623:2015 (E)
European foreword
This document (EN ISO 11623:2015) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 11623:2002.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11623:2015 has been approved by CEN as EN ISO 11623:2015 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11623:2016
---------------------- Page: 6 ----------------------
SIST EN ISO 11623:2016
INTERNATIONAL ISO
STANDARD 11623
Second edition
2015-12-01
Gas c
...
SLOVENSKI STANDARD
oSIST prEN ISO 11623:2013
01-januar-2013
3OLQVNHMHNOHQNH.RPSR]LWQLPDWHULDOL3HULRGLþQLSUHJOHGLLQSUHVNXVL ,62',6
Gas cylinders - Composite construction - Periodic inspection and testing (ISO/DIS
11623:2012)
Gasflaschen - Verbundbauweise - Wiederkehrende Inspektion und Prüfung (ISO/DIS
11623:2012)
Bouteilles à gaz transportables - Contrôles et essais périodiques des bouteilles à gaz en
matériau composite (ISO/DIS 11623:2012)
Ta slovenski standard je istoveten z: prEN ISO 11623 rev
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
oSIST prEN ISO 11623:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 11623:2013
---------------------- Page: 2 ----------------------
oSIST prEN ISO 11623:2013
EUROPEAN STANDARD
DRAFT
prEN ISO 11623 rev
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2012
ICS 23.020.30 Will supersede EN ISO 11623:2002
English Version
Gas cylinders - Composite construction - Periodic inspection
and testing (ISO/DIS 11623:2012)
Bouteilles à gaz transportables - Contrôles et essais Gasflaschen - Verbundbauweise - Wiederkehrende
périodiques des bouteilles à gaz en matériau composite Inspektion und Prüfung (ISO/DIS 11623:2012)
(ISO/DIS 11623:2012)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 23.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 11623 rev:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 11623:2013
prEN ISO 11623:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 11623:2013
prEN ISO 11623:2012 (E)
Foreword
This document (prEN ISO 11623:2012) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat
of which is held by BSI.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN ISO 11623:2002.
Endorsement notice
The text of ISO/DIS 11623:2012 has been approved by CEN as a prEN ISO 11623:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 11623:2013
---------------------- Page: 6 ----------------------
oSIST prEN ISO 11623:2013
DRAFT INTERNATIONAL STANDARD ISO/DIS 11623
ISO/TC 58/SC 4 Secretariat: ANSI
Voting begins on Voting terminates on
2012-10-11 2013-03-11
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Gas cylinders — Composite construction — Periodic inspection
and testing
Bouteilles à gaz — Construction composite — Contrôles et essais périodiques
[Revision of first edition (ISO 11623:2002)]
ICS 23.020.30
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agree
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.