Radio-frequency connectors - Part 21: Sectional specification for RF connectors with inner diameter of outer conductor 9,5 mm (0,374 in) with screw coupling-Characteristic impedance 50 ohms (Type SC) (IEC 61169-21:2022)

This part of IEC 61169, which is a sectional specification (SS), provides information and rules for preparation of detail specification for type SC threaded RF coaxial connectors with 50 Ω characteristic impedance. The connectors are used with flexible and semi-rigid cables. And they are recommended to be utilized in medium power and low reflection applications up to 11 GHz. The dielectric filled interface is especially beneficial in applications involving severe environmental exposure.
It prescribes mating face dimensions, dimensional details, gauging information for general connectors - grade 2 and standard test connectors - grade 0 as well as test schedules and inspection requirements selected from IEC 61169-1, applicable to all detail specifications relating to type SC RF connectors. Type SC interface specified in this specification is equivalent to type SC-B interface in IEC 60169-21: 1985.
This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
NOTE: For this part, original dimensions are in inches. All undimensioned pictorial configurations are for reference purpose only.

Hochfrequenz-Steckverbinder - Teil 21: Teilspezifikation für HF-Steckverbinder mit einem Innen-/Außenleiterdurchmesser von 9,5 mm mit Schraubkupplung - Charakteristische Impedanz 50 Ohm (Typ SC) (IEC 61169-21:2022)

Connecteurs pour fréquences radioélectriques - Partie 21: Spécification intermédiaire pour connecteurs RF avec conducteur extérieur de 9,5 mm (0,374 in) de diamètre intérieur à verrouillage à vis - Impédance caractéristique de 50 ohms (Type SC) (IEC 61169-21:2022)

IEC 61169-21:2022, qui est une spécification intermédiaire (SS), fournit des informations et des règles pour l’établissement de spécifications particulières (DS) relatives aux connecteurs coaxiaux RF filetés de type SC ayant une impédance caractéristique de 50 Ω. Les connecteurs sont utilisés avec des câbles flexibles et semi-rigides. Leur utilisation est recommandée dans les applications de moyenne puissance et de faible réflexion jusqu’à 11 GHz. L’interface remplie de diélectrique est particulièrement utile dans les applications impliquant une exposition à un environnement sévère.
Le présent document spécifie les dimensions de l’interface d’accouplement, les détails dimensionnels, les informations relatives aux calibres pour les connecteurs à usage général (grade 2) et les connecteurs d’essai normalisés (grade 0), ainsi que les programmes d’essais et les exigences de contrôle choisis dans l’IEC 61169-1, applicables à toutes les spécifications particulières relatives aux connecteurs RF de type SC. L’interface de type SC indiquée dans le présent document est équivalente à l’interface de type SC-B de l’IEC 60169-21:1985.
Le présent document indique les caractéristiques de performance recommandées à prendre en compte lors de la rédaction d’une spécification particulière, et il couvre les programmes d’essai et les exigences de contrôle pour les niveaux d’assurance M et H.

Radiofrekvenčni konektorji - 21. del: Področna specifikacija za radiofrekvenčne (RF) konektorje z notranjim premerom zunanjega vodnika 9,5 mm (0,374 in) z navojnim spajanjem - Karakteristična impedanca 50 ohm (tip SC) (IEC 61169-21:2022)

Ta del standarda IEC 61169, ki je področna specifikacija (SS), podaja informacije in določa pravila za pripravo podrobnih specifikacij za navojne radiofrekvenčne koaksialne konektorje tipa SC s karakteristično impedanco 50 Ω. Konektorji se uporabljajo s prožnimi in poltrdimi kabli. Priporočljivo jih je uporabljati pri srednji moči in nizkem odboju do 11 GHz. Dielektrični vmesnik je še posebej koristen pri uporabi konektorjev, ki so resno izpostavljeni okolju.
Opisuje mere spojne površine, podrobnosti o merah, informacije o merjenju splošnih konektorjev – tipa 2 in standardnih preskusnih konektorjev – tipa 0 pa tudi razporede preskusov in zahteve pregledov, izbranih iz standarda IEC 61169-1, ki se uporabljajo za vse podrobne specifikacije v zvezi z radiofrekvenčnimi konektorji tipa SC. Vmesnik tipa SC, določen v tej specifikaciji, je enakovreden vmesniku tipa SC-B v standardu IEC 60169-21: 1985.
Ta specifikacija določa priporočene lastnosti, ki jih je treba upoštevati pri sestavljanju podrobne specifikacije, ter zajema urnike preskusov in zahteve za pregled za ravni vrednotenja M in H.
OPOMBA: Izvirne mere v tem delu so podane v palcih. Vse nedimenzionirane slikovne konfiguracije so podane samo v referenčne namene.

General Information

Status
Published
Publication Date
13-Apr-2022
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
08-Apr-2022
Due Date
13-Jun-2022
Completion Date
14-Apr-2022

Buy Standard

Standard
EN IEC 61169-21:2022
English language
32 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61169-21:2022
01-junij-2022
Radiofrekvenčni konektorji - 21. del: Področna specifikacija za radiofrekvenčne
(RF) konektorje z notranjim premerom zunanjega vodnika 9,5 mm (0,374 in) z
navojnim spajanjem - Karakteristična impedanca 50 ohm (tip SC) (IEC 61169-
21:2022)
Radio-frequency connectors - Part 21: Sectional specification for RF connectors with
inner diameter of outer conductor 9,5 mm (0,374 in) with screw coupling-Characteristic
impedance 50 ohms (Type SC) (IEC 61169-21:2022)
Hochfrequenz-Steckverbinder - Teil 21: Teilspezifikation für HF-Steckverbinder mit
einem Innen-/Außenleiterdurchmesser von 9,5 mm mit Schraubkupplung -
Charakteristische Impedanz 50 Ohm (Typ SC) (IEC 61169-21:2022)
Connecteurs pour fréquences radioélectriques - Partie 21: Spécification intermédiaire
pour connecteurs RF avec conducteur extérieur de 9,5 mm (0,374 in) de diamètre
intérieur à verrouillage à vis - Impédance caractéristique de 50 ohms (Type SC) (IEC
61169-21:2022)
Ta slovenski standard je istoveten z: EN IEC 61169-21:2022
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 61169-21:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61169-21:2022

---------------------- Page: 2 ----------------------
SIST EN IEC 61169-21:2022


EUROPEAN STANDARD EN IEC 61169-21

NORME EUROPÉENNE

EUROPÄISCHE NORM April 2022
ICS 33.120.30

English Version
Radio-frequency connectors - Part 21: Sectional specification for
RF connectors with inner diameter of outer conductor 9,5 mm
(0,374 in) with screw coupling - Characteristic impedance 50
ohms (Type SC)
(IEC 61169-21:2022)
Connecteurs pour fréquences radioélectriques - Partie 21: Hochfrequenz-Steckverbinder - Teil 21:
Spécification intermédiaire relatives aux connecteurs RF Rahmenspezifikation für HF-Steckverbinder mit einem
avec conducteur extérieur de 9,5 mm (0,374 in) de diamètre Innen-/Außenleiterdurchmesser von 9,5 mm mit
intérieur à verrouillage à vis - Impédance caractéristique de Schraubkupplung - Wellenwiderstand 50 Ohm (Typ SC)
50 ohms (Type SC) (IEC 61169-21:2022)
(IEC 61169-21:2022)
This European Standard was approved by CENELEC on 2022-03-25. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61169-21:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61169-21:2022
EN IEC 61169-21:2022 (E)
European foreword
The text of document 46F/601/FDIS, future edition 1 of IEC 61169-21, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-21:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-12-25
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-03-25
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61169-21:2022 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 61169-21:2022
EN IEC 61169-21:2022 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61169-1-6 - Radio-frequency connectors - Part 1-6: - -
Electrical test methods - RF power
IEC 60169-21 1985 Radio-frequency connectors. Part 21: Two EN 60169-21 1997
types of radio-frequency connectors with
inner diameter of outer conductor 9.5 mm
(0.374 in) with different versions of screw
coupling - Characteristic impedance 50
ohms (Types SC-A and SC-B)
IEC 62153-4-7 - Metallic cables and other passive EN IEC 62153-4-7 -
components test methods - Part 4-7:
Electromagnetic compatibility (EMC) -Test
method for measuring of transfer
impedance Z and screening attenuation
T
aS or coupling attenuation aC of connectors
and assemblies - Triaxial tube in tube
method


3

---------------------- Page: 5 ----------------------
SIST EN IEC 61169-21:2022

---------------------- Page: 6 ----------------------
SIST EN IEC 61169-21:2022



IEC 61169-21

®


Edition 1.0 2022-02




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Radio-frequency connectors –

Part 21: Sectional specification for RF connectors with inner diameter of outer

conductor 9,5 mm (0,374 in) with screw coupling − Characteristic impedance

50 ohms (Type SC)



Connecteurs pour fréquences radioélectriques –


Partie 21: Spécification intermédiaire relatives aux connecteurs RF avec

conducteur extérieur de 9,5 mm (0,374 in) de diamètre intérieur à verrouillage

à vis – Impédance caractéristique de 50 ohms (Type SC)











INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.30 ISBN 978-2-8322-1079-6




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61169-21:2022
– 2 – IEC 61169-21:2022 © IEC 2022
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Mating face and gauge information . 7
4.1 Dimensions – General connectors – Grade 2 . 7
4.1.1 Connector with pin-centre contact . 7
4.1.2 Connector with socket-centre contact . 9
4.2 Gauges . 11
4.2.1 Pin connectors − outer contact . 11
4.2.2 Socket connectors − centre contact . 12
4.3 Standard test connectors – Grade 0 . 13
4.3.1 General . 13
4.3.2 Standard test connector with pin-centre contact . 13
4.3.3 Standard test connector with socket-centre contact . 15
5 Quality assessment procedures . 17
5.1 General . 17
5.2 Ratings and characteristics . 18
5.3 Test schedule and inspection requirements. 20
5.3.1 Acceptance tests . 20
5.3.2 Periodic tests . 21
5.4 Procedures for the quality conformance . 23
5.4.1 Quality conformance inspection . 23
5.4.2 Qualification approval and its maintenance . 23
6 Instructions for preparation of detail specifications (DS) . 23
6.1 General . 23
6.2 Identification of the component . 24
6.3 Performances . 24
6.4 Marking, ordering information and related matters . 24
6.5 Selection of tests, test conditions and severities . 24
6.6 Blank detail specification pro-forma for type SC connector . 25

Figure 1 – Connector with pin-centre contact . 8
Figure 2 – Connector with socket-centre contact . 10
Figure 3 – Gauge for outer contact of pin connector . 11
Figure 4 – Gauge for centre contact of socket connector . 12
Figure 5 – Standard test connector with pin-centre contact . 14
Figure 6 – Standard test connector with socket-centre contact . 16

Table 1 – Dimensions of connector with pin-centre contact . 9
Table 2 – Dimensions of connector with socket-centre contact . 11
Table 3 – Dimensions of gauge for outer contact of pin connector . 12
Table 4 – Dimensions of gauge for centre contact of socket connector . 13
Table 5 – Dimensions of standard test connector with pin-centre contact . 15
Table 6 – Dimensions of standard test connector with socket-centre contact . 17

---------------------- Page: 8 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 3 –
Table 7 – Rating and characteristics . 18
Table 8 – Acceptance tests . 21
Table 9 – Periodic tests . 22

---------------------- Page: 9 ----------------------
SIST EN IEC 61169-21:2022
– 4 – IEC 61169-21:2022 © IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 21: Sectional specification for RF connectors with inner
diameter of outer conductor 9,5 mm (0,374 in) with screw coupling −
Characteristic impedance 50 ohms (Type SC)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61169-21 has been prepared by subcommittee 46F: RF and microwave passive
components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF
and microwave passive components and accessories. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
46F/601/FDIS 46F/613/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

---------------------- Page: 10 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 5 –
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------
SIST EN IEC 61169-21:2022
– 6 – IEC 61169-21:2022 © IEC 2022
RADIO-FREQUENCY CONNECTORS –

Part 21: Sectional specification for RF connectors with inner
diameter of outer conductor 9,5 mm (0,374 in) with screw coupling −
Characteristic impedance 50 ohms (Type SC)



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for type SC threaded RF coaxial connectors with
50 Ω characteristic impedance. The connectors are used with flexible and semi-rigid cables.
They are recommended for use in medium power and low reflection applications up to 11 GHz.
The dielectric filled interface is especially beneficial in applications involving severe
environmental exposure.
This document specifies mating face dimensions, dimensional details, gauging information for
general connectors − grade 2 and standard test connectors − grade 0 as well as test schedules
and inspection requirements selected from IEC 61169-1, applicable to all detail specifications
relating to type SC RF connectors. Type SC interface specified in this document is equivalent
to type SC-B interface in IEC 60169-21:1985.
This document indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference
purpose only.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61169-1:2013, Radio-frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 61169-1-6, Radio-frequency connectors – Part 1-6: Electrical test methods – RF power
IEC 60169-21:1985, Radio-frequency connectors – Part 21: Two types of radio-frequency
connectors with inner diameter of outer conductor 9,5 mm (0,374 in) with different versions of
screw coupling − Characteristic impedance 50 ohms (Types SC-A and SC-B)
IEC 62153-4-7, Metallic cables and other passive components test methods − Part 4-7:
Electromagnetic compatibility (EMC) − Test method for measuring of transfer impedance Z
T
and screening attenuation a or coupling attenuation a of connectors and assemblies − Triaxial
S C
tube in tube method
3 Terms and definitions
No terms and definitions are listed in this document.

---------------------- Page: 12 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 7 –
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Mating face and gauge information
4.1 Dimensions – General connectors – Grade 2
4.1.1 Connector with pin-centre contact
The mating face of a connector with pin-centre contact is shown in Figure 1 and its dimensions
are shown in Table 1.

---------------------- Page: 13 ----------------------
SIST EN IEC 61169-21:2022
– 8 – IEC 61169-21:2022 © IEC 2022

NOTE 1 Slot design is optional.
NOTE 2 Three holes with diameter of 0,69 mm (0,027 in) minimum equally spaced for safety wiring. Location on
coupling nut is optional.
NOTE 3 Sealing gasket to give required environmental performance.
NOTE 4 Taper of pin contact starts here.
NOTE 5 Spherical or chamfered.
NOTE 6 Mechanical and electrical reference plane.
Figure 1 – Connector with pin-centre contact

---------------------- Page: 14 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 9 –
Table 1 – Dimensions of connector with pin-centre contact
mm in
Ref.
Min. Max. Min. Max.
a 4,93 — 0,194 —
b 7,01 — 0,276 —
a
— — — —
d
e 17,53 — 0,690 —
b
5,41 5,66 0,213 0,223
g
b
0,64 2,16 0,025 0,085
m
n 0,18 — 0,007 —
p 2,36 — 0,093 —
r 7,85 — 0,309 —
t 3,02 3,15 0,119 0,124
u 7,80 8,56 0,307 0,337
v 0,08 1,02 0,003 0,040
b
6,35 — 0,250 —
y
z 2,29 2,34 0,090 0,092
aa — 21,03 — 0,828
a
Dimensions shall meet requirements of mating characteristics.
b
Applicable when coupling nut is urged forward.

4.1.2 Connector with socket-centre contact
The mating face of a connector with socket-centre contact is shown in Figure 2 and its
dimensions are shown in Table 2.

---------------------- Page: 15 ----------------------
SIST EN IEC 61169-21:2022
– 10 – IEC 61169-21:2022 © IEC 2022

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Applies to dielectric extending beyond reference plane.
NOTE 3 Slot design optional. Contact is closed.
Figure 2 – Connector with socket-centre contact

---------------------- Page: 16 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 11 –
Table 2 – Dimensions of connector with socket-centre contact
mm in
Ref.
Min. Max. Min. Max.
a — 4,83 — 0,190
b — 6,91 — 0,272
c — 9,50 — 0,374
d 10,44 10,54 0,411 0,415
e 12,24 12,65 0,482 0,498
f — 16,00 — 0,630
g 1,19 1,96 0,047 0,077
k 7,54 — 0,297 —
l 12,47 12,57 0,491 0,495
m 16,03 — 0,631 —
n — 0,18 — 0,007
p 6,93 7,70 0,273 0,303
r — 7,85 — 0,309
s 7,62 — 0,300 —
a
3,02 3,15 0,119 0,124
t
b
0,25 — 0,010 —
ff
a
Tolerance to be chosen so that the reflection factor requirement is met.
b
Fillet.

4.2 Gauges
4.2.1 Pin connectors − outer contact
The gauge for outer contact of pin connector is shown in Figure 3 and its dimensions are shown
in Table 3.
Dimensions in millimetres (inches)

Figure 3 – Gauge for outer contact of pin connector

---------------------- Page: 17 ----------------------
SIST EN IEC 61169-21:2022
– 12 – IEC 61169-21:2022 © IEC 2022
Table 3 – Dimensions of gauge for outer contact of pin connector
Gauge B
Gauge A
(For slotted outer contacts)
(For outer contacts)
+5
Mass of gauge: 200 g
0
Ref.
mm in mm in
Min. Max. Min. Max. Min. Max. Min. Max.
a 10,426 10,439 0,410 5 0,411 0 10,643 10,656 0,419 0 0,419 5
b 3,180 — 0,125 0 — 0,790 — 0,031 0 —
Material: polished steel with a 0,4 µm (16 µin) finish.

Test procedures are as follows:
a) For outer contacts, a steel test ring A (Figure 3) with inner diameter "a" shall be pushed over
the outer electrical contact of the connector. The insertion force shall not exceed 66 N when
the outer contact inserts into the gauge A at a minimum distance of "b".
b) For slotted outer contacts, a steel test ring B (Figure 3) with an inner diameter "a" shall be
placed over the outer electrical contact of the connector. The test ring shall uniformly meet
the outer electrical contact when pushed no more than 0,79 mm (0,031 in) over this contact.
4.2.2 Socket connectors − centre contact
The gauge for centre contact of a socket connector is shown in Figure 4 and its dimensions are
shown in Table 4.
Dimensions in millimetres (inches)

Figure 4 – Gauge for centre contact of socket connector

---------------------- Page: 18 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 13 –
Table 4 – Dimensions of gauge for centre contact of socket connector
Gauges B
Gauges A
(For retention test)
(For sizing purpose)
Mass of gauge: 56 g
Ref.
mm in mm in
Min. Max. Min. Max. Min. Max. Min. Max.
a 2,337 2,342 0,092 0 0,092 2 2,276 2,286 0,089 6 0,090 0
b 3,180 — 0,125 0 — — — — —
Material: polished steel with a 0,4 µm (16 µin) finish.

Test procedures are as follows:
a) A steel test pin A (Figure 4) with a diameter "a" shall be inserted into the centre contact at
a minimum distance of 3,18 mm (0,125 in). This is a sizing operation.
b) After completion of item a), a second steel test pin B (Figure 4) with a diameter "a" shall
have a minimum withdrawal force of 0,56 N after insertion into the centre electrical contact.
4.3 Standard test connectors – Grade 0
4.3.1 General
These dimensions are for standard test connector adapters for reflection factor testing.
4.3.2 Standard test connector with pin-centre contact
The mating face of a standard test connector with pin-centre contact is shown in Figure 5 and
its dimensions are shown in Table 5.

---------------------- Page: 19 ----------------------
SIST EN IEC 61169-21:2022
– 14 – IEC 61169-21:2022 © IEC 2022

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Taper of pin contact starts here.
Figure 5 – Standard test connector with pin-centre contact

---------------------- Page: 20 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 15 –
Table 5 – Dimensions of standard test connector with pin-centre contact
mm in
Ref.
Min. Max. Min. Max.
a 4,930 5,030 0,194 0 0,198 0
b 7,010 7,110 0,276 0 0,280 0
a
9,880 9,898 0,388 9 0,389 7
c
d 10,340 10,390 0,407 0 0,409 0
n 0,180 0,330 0,007 0 0,013 0
r 7,850 8,080 0,309 0 0,318 0
s 7,650 7,770 0,301 0 0,306 0
a
3,030 3,050 0,119 2 0,120 2
t
u 7,800 7,900 0,307 0 0,311 0
z 2,286 2,339 0,090 0 0,092 1
bb 1,040 1,300 0,041 0 0,051 0
cc 2,360 2,620 0,093 0 0,103 0
b
— 0,100 — 0,004 0
ff
ar — 0,076 — 0,003 0
at — 0,102 — 0,004 0
az — 0,010 — 0,000 5
br — 0,076 — 0,003 0
a
These diameters are for PTFE insulation with dielectric constant 2,02.
Characteristic impedance shall be (50 ± 0,2) Ω.
b
Fillet or chamfer.

4.3.3 Standard test connector with socket-centre contact
The mating face of a standard test connector with socket-centre contact is shown in
Figure 6 and its dimensions are shown in Table 6.

---------------------- Page: 21 ----------------------
SIST EN IEC 61169-21:2022
– 16 – IEC 61169-21:2022 © IEC 2022

NOTE 1 Mechanical and electrical reference plane.
NOTE 2 Tolerance chosen so that reflection factor requirements are met.
Figure 6 – Standard test connector with socket-centre contact

---------------------- Page: 22 ----------------------
SIST EN IEC 61169-21:2022
IEC 61169-21:2022 © IEC 2022 – 17 –
Table 6 – Dimensions of standard test connector with socket-centre contact
mm in
Ref. Note
Min. Min. Min. Min.
a 4,780 4,830 0,188 0 0,190 0
b 6,810 6,910 0,268 0 0,272 0
c 8,990 9,040 0,354 0 0,356 0
d 10,440 10,540 0,411 0 0,415 0
p 7,540 7,750 0,297 0 0,305 0
r 7,700 7,850 0,303 0 0,309 0
s 7,770 — 0,306 0 —
a
t 3,030 3,050 0,119 2 0,120 2
w 0,510 1,020 0,020 0 0,040 0 straight section
b
ae 3,188 3,213 0,125 5 0,126 5
af 2,461 2,517 0,096 9 0,099 1
ag 2,790 3,000 0,110 0 0,118 0
ah 0,380 0,890 0,015 0 0,035 0
ak 2,620 — 0,103 0 —
am 8,560 Nominal 0,337 0 Nominal
as 0,200 0,300 0,007 9 0,001 2
rr 0,300 0,500 0,001 2 0,019 7 radius
at — 0,100 — 0,004 0 radius
ee 9,880 Nominal 0,389 0 Nominal
gg — — — —
kk 12,470 12,570 0,491 0 0,495 0
ll 12,240 12,650
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.