SIST EN 13244-5:2003

Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system

This Part of EN (155wi017) specifies the characteristics of the fitness for purpose of the assembled polyethylene piping systems intended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. It also specifies the test parameters for the test methods referred to in this standard.

Kunstoff-Rohrleitungssysteme für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser - Polyethylen (PE) - Teil 5: Gebrauchstauglichkeit des Systems

Dieser Teil von EN 13244 legt die Anforderungen an die Gebrauchstauglichkeit von Rohrleitungssystemen aus Polyethylen (PE) fest, die für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser eingesetzt werden. Er gilt auch für Vakuum-Abwassersysteme.
ANMERKUNG 1   Brauchwasser ist nicht für den menschlichen Gebrauch bestimmt und Rohrleitungsteile, die dieser Norm entsprechen, sollten nicht für die Wasserversorgung für den menschlichen Gebrauch verwendet werden. Rohrleitungsteile aus PE für die Verwendung in der Wasserversorgung für den menschlichen Gebrauch und die Fortleitung von Rohwasser, das zur Aufbereitung von Trinkwasser genutzt wird, siehe EN 12201[5].
Er legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird.
Zusammen mit den übrigen Teilen der EN 13244 (siehe Vorwort) gilt dieser Teil für Rohre, Formstücke und Armaturen aus PE, deren Verbindungen untereinander sowie mit Rohrleitungsteilen aus anderen Werkstoffen, die zur Verwendung unter den folgenden Bedingungen vorgesehen sind:
   Verlegung im Rohrgraben;
   Entwässerung ins Meer (Siele);
   Überlandleitungen in Binnengewässern oder in Kanälen;
   Düker und Brückenleitungen;
   der maximal zulässige Betriebsdruck MOP beträgt nicht mehr als 25 bar  ;
   es gilt eine Betriebstemperatur von 20 °C als Bezugstemperatur.
ANMERKUNG 2   Für Anwendungsgebiete, in denen konstante Betriebstemperaturen über 20 °C bis maximal 40 °C auftreten, siehe Anhang A, EN 13244-1:2002.
EN 13244 enthält Festlegungen über maximal zulässige Betriebsdrücke und legt Anforderungen an die Einfärbung von Rohrleitungsteilen sowie die Verwendung von Zusatzstoffen fest.
ANMERKUNG 3   Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der geltenden nationalen Empfehlungen oder Festlegungen und Verlegepraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.

Systemes de canalisations en plastique pour les applications générales de transport d'eau, de branchement et de collecteurs d'assainissement, enterrés sous pression - Polyéthylene (PE) - Partie 5: Aptitude a l'emploi du systeme

La présente partie de l'EN 13244 spécifie les aspects généraux des systemes de canalisations en polyéthylene pour les applications générales de transport d'eau, de branchements et de collecteurs d'assainissement enterrés et aériens sous pression. Elle s'applique aussi aux systemes de collecteurs par le vide.
NOTE 1   L'eau pour les applications générales n'est pas destinée a  la consommation humaine et il convient que les composants conformes a cette norme ne soient utilisés pour des systemes de transport d'eau pour la consommation humaine. Pour les composants PE destinés au transport de l'eau pour la consommation humaine y compris les eaux brutes avant traitement , voir l'EN 12201[5] .
Elle spécifie également les parametres d'essai pour les méthodes d'essai auxquelles il est fait référence dans la présente norme.
Conjointement aux autres parties de l'EN 13244 (voir avant-propos), elle s'applique aux tubes, raccords, robinets en PE, a leurs assemblages et aux assemblages avec des composants fabriqués en d'autres matieres destinés a etre utilisés selon les conditions suivantes :
   enterrés dans le sol ;
   déversoirs en mer ;
   posés dans l'eau ;
   au dessus du sol, y compris les tubes suspendus sous les ponts ;
   a une pression de service maximale, MOP, pouvant atteindre jusqu'a 25 bar ) ;
   a une température de service de 20 °C comme température de référence.
NOTE 2   Pour des applications fonctionnant a des températures constantes supérieures a 20 °C et jusqu'a 40 °C voir l'Annexe A de l'EN 13244-1 :2002.
L'EN 13244 comprend une gamme étendue de pressions de service et spécifie les exigences concernant les couleurs et les additifs.
NOTE 3   Il est de la responsabilité de l'acheteur ou du prescripteur d'effectuer le choix approprié de ces aspects, prenant en compte les exigences particulieres et les regles nationales correspondantes ainsi que les pratiques ou les codes de pose.

Cevni sistemi iz polimernih materialov, podzemni in nadzemni, za tlačne vodovode splošne namembnosti, odvodnjavanje in kanalizacijo - Polietilen (PE) - 5. del: Ustreznost sistema namenu

General Information

• Status: Withdrawn
• Publication Date: 30-Sep-2003
• Withdrawal Date: 07-Nov-2011
• ICS: 23.040.05 - Pipeline and its parts for external sewage systems
• ICS: 93.030 - External sewage systems
• Technical Committee: PCV - Plastic pipes, fittings and valves
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 08-Nov-2011
• Due Date: 01-Dec-2011
• Completion Date: 08-Nov-2011
• Directive: 89/106/EEC - Construction products
• Ref Project: EN 13244-5:2002 - Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system

Relations

• Replaced By: SIST EN 12201-5:2011 - Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system
• Effective Date: 01-Dec-2011

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunstoff-Rohrleitungssysteme für erd- und oberirdisch verlegte Druckrohrleitungen für Brauchwasser, Entwässerung und Abwasser - Polyethylen (PE) - Teil 5: Gebrauchstauglichkeit des SystemsSystemes de canalisations en plastique pour les applications générales de transport d'eau, de branchement et de collecteurs d'assainissement, enterrés sous pression - Polyéthylene (PE) - Partie 5: Aptitude a l'emploi du systemePlastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system93.030Zunanji sistemi za odpadno vodoExternal sewage systems23.040.01Deli cevovodov in cevovodi na splošnoPipeline components and pipelines in generalICS:Ta slovenski standard je istoveten z:EN 13244-5:2002SIST EN 13244-5:2003en01-oktober-2003SIST EN 13244-5:2003SLOVENSKI
STANDARD



SIST EN 13244-5:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13244-5December 2002ICS 93.030English versionPlastics piping systems for buried and above-ground pressuresystems for water for general purposes, drainage and sewerage- Polyethylene (PE) - Part 5: Fitness for purpose of the systemSystèmes de canalisations en plastique pour lesapplications générales de transport d'eau, de branchementet de collecteurs d'assainissement, enterrés sous pression- Polyéthylène (PE) - Partie 5: Aptitude à l'emploi dusystèmeKunstoff-Rohrleitungssysteme für erd- und oberirdischverlegte Druckrohrleitungen für Brauchwasser,Entwässerung und Abwasser - Polyethylen (PE) - Teil 5:Gebrauchstauglichkeit des SystemsThis European Standard was approved by CEN on 16 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13244-5:2002 ESIST EN 13244-5:2003



EN 13244-5:2002 (E)2ContentspageForeword.3Introduction.41Scope.52Normative references.53Definitions, symbols and abbreviations.64Fitness for purpose of the system.74.1General.74.2Preparation of assemblies for testing.74.3Butt fusion joints.74.4Electrofusion joints.84.5Mechanical jointing.94.6Conditioning.94.7Retest in case of failure at 80 °C.104.8Compatibility.11Bibliography.12SIST EN 13244-5:2003



EN 13244-5:2002 (E)3ForewordThis document (EN 13244-5:2002) has been prepared by Technical Committee CEN/TC 155 "Plastics pipingsystems and ducting systems", the secretariat of which is held by NEN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2003, and conflicting national standards shall be withdrawn at the latest byDecember 2004.For components which have conformed to the relevant national standard before December 2002, as shown by themanufacturer or by a certification body, the national standard may continue to be applied until December 2004.It has been prepared in liaison with CEN/TC 165 "Waste water engineering".This European Standard is a Part of a System Standard for plastics piping systems, which is a standard for plasticspiping of a particular material for a specified application. There are a number of such Systems Standards.System Standards are based on the results of the work being undertaken in ISO/TC 138 "Plastics pipes, fittingsand valves for the transport of fluids", which is a Technical Committee of the International Organization forStandardization (ISO).They are supported by separate standards on test methods to which references are made throughout the SystemStandard.The System Standards are consistent with standards on general functional requirements and standards oninstallation practices.EN 13244 consists of the following Parts, under the general title Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage — Polyethylene (PE).— Part 1: General— Part 2: Pipes— Part 3: Fittings— Part 4: Valves— Part 5: Fitness for purpose of the system (this standard)— Part 7: Guidance for the assessment of conformity (to be published as an CEN/TS)NOTEIt was decided not to publish a Part 6: Recommended practice for installation. Instead, existing national practiceswould be applicable.This Part of EN 13244 includes a Bibliography.System Standards for piping systems of other plastics materials used for the conveyance of water include thefollowing:prEN 14364,
Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforcedthermosetting (GRP) plastics based on polyester resin (UP).EN 1456,
Plastics piping systems for buried and above-ground drainage and sewerage under pressure —Unplasticized poly(vinyl chloride) (PVC-U).According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdom.SIST EN 13244-5:2003



EN 13244-5:2002 (E)4IntroductionEN 13244, of which this is Part 5, specifies the requirements for a piping system and its components when madefrom polyethylene (PE). It is intended to be used for buried and above-ground pressure systems for water forgeneral purposes, drainage and sewerage, including vacuum systems.Requirements and test methods for components of the piping system are specified in EN 13244-1,EN 13244-2[1], EN 13244-3[2] and EN 13244-4[3]. prCEN/TS 13244-7[4] gives guidance for the assessment ofconformity.This Part of EN 13244 covers the characteristics of the fitness for purpose of the system.SIST EN 13244-5:2003



EN 13244-5:2002 (E)51 ScopeThis Part of EN 13244 specifies the characteristics of the fitness for purpose of the assembled piping systemsintended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Itis also applicable for vacuum sewer systems.NOTE 1Water for general purposes is not intended for human consumption and components conforming to this standardshould not be used in systems conveying water for human consumption. For PE components intended for the conveyance ofwater intended for human consumption and raw water prior to treatment, see EN 12201[5].It also specifies the test parameters for the test methods referred to in this standard.In conjunction with other Parts of EN 13244 (see Foreword), it is applicable to PE pipes, fittings, valves, their jointsand to joints with components of other materials intended to be used as follows:¾ buried in the ground;¾ sea outfalls;¾ laid in water;¾ above-ground, including pipes suspended below bridges;¾ a maximum operating pressure, MOP, up to and including 25 bar1);¾ an operating temperature of 20 °C as a reference temperature.NOTE 2For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see annex A ofEN 13244-1:2002.EN 13244 covers a range of maximum operating pressures and gives requirements concerning colours andadditives.NOTE 3It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking intoaccount their particular requirements and any relevant national guidance or regulations and installation practices or codes.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 712,
Thermoplastics piping systems — End-load-bearing mechanical joints between pressure pipes andfittings — Test method for resistance to pull-out under constant longitudinal force.EN 713,
Plastics piping systems — Mechanical joints between fittings and polyolefin pressure pipes — Testmethod for leaktightness under internal pressure of assemblies subjected to bending.EN 715,
Thermoplastics piping systems — End-load-bearing joints between small diameter pressure pipes andfittings — Test method for leaktightness under internal water pressure, including end thrust.EN 911,
Plastics piping systems — Elastomeric sealing ring type joints and mechanical joints for thermoplasticspressure piping — Test method for leaktightness under external hydrostatic pressure.
1)1 bar = 105 N/m2.SIST EN 13244-5:2003



EN 13244-5:2002 (E)6EN 921:1994,
Plastics piping systems — Thermoplastics pipes — Determination of resistance to internal pressureat constant temperature.EN 13244-1:2002,
Plastics piping systems for buried and above-ground pressure systems for water for generalpurposes, drainage and sewerage — Polyethylene (PE) — Part 1: General.ISO 11413:1996,
Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE)pipe and an electrofusion fitting.ISO 11414:1996,
Plastics pipes and fittings — Preparation of polyeth
...