SIST EN 13604:2004
(Main)Copper and copper alloys - Products of high conductivity copper for electronic tubes, semiconductor devices and vacuum applications
Copper and copper alloys - Products of high conductivity copper for electronic tubes, semiconductor devices and vacuum applications
This European Standard specifies the composition, property requirements including electrical properties and
tolerances on dimensions and form of two copper grades Cu-OFE (CW009A) and Cu-PHCE (CW022A), for
electronic and semiconductor devices as well as for vacuum applications, in the form of wrought products, e.g. plate,
sheet, strip, seamless tube, rod, bar, wire, profiles.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and
the delivery conditions are also specified.
This European Standard applies to the wrought copper products as delivered to the device manufacturer, i.e. for
further fabrication.
Kupfer und Kupferlegierungen - Produkte aus hochleitfähigem Kupfer für Elektronenröhren, Halbleiterbauelemente und für die Anwendung in der Vakuumtechnik
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften, einschließlich
elektrische Eigenschaften, Grenzabmaße und Formtoleranzen der zwei Kupfersorten Cu-OFE (CW009A) und
Cu-PHCE (CW022A) für die Anwendung in der Elektronik, als Halbleiterbauelemente und für die Vakuumtechnik fest,
und zwar als Produkte, die durch plastisches Umformen hergestellt wurden, z. B. Platten, Bleche, Bänder, nahtlose
Rohre, Stangen, Drähte und Profile.
Der Ablauf der Probenentnahme, die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen
dieser Norm und die Lieferbedingungen sind ebenfalls festgelegt.
Diese Europäische Norm gilt für Produkte aus Kupfer, die durch plastisches Umformen hergestellt wurden, so wie
sie an die Hersteller von Bauteilen geliefert werden, d. h. zur weiteren Bearbeitung.
Cuivre et alliages de cuivre - Produits en cuivre de haute conductivité pour application dans les tubes électroniques, semi-conducteurs et vide
La présente Norme européenne spécifie la composition, les caractéristiques, y compris les caractéristiques électriques et les tolérances de dimensions et de formes des deux nuances de cuivre Cu-OFE (CW009A) et Cu-PHCE (CW022A), pour les dispositifs électroniques et semi-conducteurs ainsi que pour les applications de vide, se présentant sous la forme de produits corroyés, par exemple plaque, tôle, bande, tube sans soudure, barre, fil, profilés.
Les procédures d'échantillonnage, les méthodes d'essai pour la vérification de la conformité aux exigences de la présente norme et les conditions de livraison sont également spécifiées.
La présente norme européenne s'applique aux produits en cuivre corroyé tels qu'ils sont livrés au fabricant du dispositif, a savoir pour toute fabrication ultérieure.
Baker in bakrove zlitine – Izdelki iz visoko prevodnega bakra za elektronske cevi, polprevodniške sklope in uporabo v vakuumu
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine – Izdelki iz visoko prevodnega bakra za elektronske cevi, polprevodniške sklope in uporabo v vakuumuKupfer und Kupferlegierungen - Produkte aus hochleitfähigem Kupfer für Elektronenröhren, Halbleiterbauelemente und für die Anwendung in der VakuumtechnikCuivre et alliages de cuivre - Produits en cuivre de haute conductivité pour application dans les tubes électroniques, semi-conducteurs et videCopper and copper alloys - Products of high conductivity copper for electronic tubes, semiconductor devices and vacuum applications77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 13604:2002SIST EN 13604:2004en01-januar-2004SIST EN 13604:2004SLOVENSKI
STANDARD
SIST EN 13604:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13604July 2002ICS 77.150.30English versionCopper and copper alloys - Products of high conductivity copperfor electronic tubes, semiconductor devices and vacuumapplicationsCuivre et alliages de cuivre - Produits en cuivre de hauteconductivité pour application dans les tubes électroniques,semi-conducteurs et videKupfer und Kupferlegierungen - Produkte aushochleitfähigem Kupfer für Elektronenröhren,Halbleiterbauelemente und für die Anwendung in derVakuumtechnikThis European Standard was approved by CEN on 14 March 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13604:2002 ESIST EN 13604:2004
EN 13604:2002 (E)ContentspagepageForeword .31Scope .42Normative references .43Terms and definitions .54Designations .54.1Material .54.2Material condition .54.3Product .55Ordering information .66Requirements .76.1Composition .76.2Mechanical properties .76.3Electrical properties .86.4Freedom from hydrogen embrittlement .86.5Scale adhesion .86.6Grain size .86.7Tolerances of dimensions and form .86.8Surface condition .97Sampling .97.1General .97.2Analysis .97.3Mechanical, electrical and other tests .98Test methods .108.1Analysis .108.2Tensile test .10
8.3Hardness test .10
8.4Bend test .10
8.5Electrical test .10
8.6Hydrogen embrittlement test .11
8.7Scale adhesion test .11
8.8Estimation of average grain size .11
8.9Retests .11
8.10Rounding of results .11
9Declaration of conformity andinspection documentation .11
9.1Declaration of conformity .11
9.2Inspection documentation .1210Marking, labelling, packaging .12Annex A
(normative)
Reference chartfor microscopic examination atmagnification 100× .15Annex B
(informative)
Characteristics ofcoppers for electrical purposes .16Bibliography .18TablesTable 1 — Composition of Cu-OFE and Cu-PHCE
..................13Table 2 — Electrical properties (at 20 °C) ...14Table B.1 — Particular characteristics ofcoppers for electrical purposes .....172SIST EN 13604:2004
EN 13604:2002 (E)ForewordThis document EN 13604:2002 has been prepared by Technical Committee CEN/TC 133 "Copper and copperalloys", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by January 2003, and conflicting national standards shall be withdrawn at the latestby January 2003.Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 5 "Copper forelectrical purposes" to prepare the following standard:EN 13604,
Copper and copper alloys — Products of high conductivity copper for electronic tubes, semiconductordevices and vacuum applications.The two copper grades Cu-OFE (CW009A) and Cu-PHCE (CW022A) specified in this European Standard are thosewhich are especially suitable for electronic, semiconductor and vacuum applications.Annex A (normative) is the reference for microscopic examination. Annex B (informative) gives guidance on the characteristics of coppers for electrical purposes.This is one of a series of European Standards for copper products for electrical purposes. Other copper productsare specified as follows:EN 13599,
Copper and copper alloys — Copper plate, sheet and strip for electrical purposes.EN 13600,
Copper and copper alloys — Seamless copper tubes for electrical purposes.EN 13601,
Copper and copper alloys — Copper rod, bar and wire for general electrical purposes.EN 13602,
Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical conductors.EN 13605,
Copper and copper alloys — Copper profiles and profiled wire for electrical purposes.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countriesare bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France,Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden,Switzerland and the United Kingdom.33SIST EN 13604:2004
EN 13604:2002 (E)1
ScopeThis European Standard specifies the composition, property requirements including electrical properties andtolerances on dimensions and form of two copper grades Cu-OFE (CW009A) and Cu-PHCE (CW022A), forelectronic and semiconductor devices as well as for vacuum applications, in the form of wrought products, e.g. plate,sheet, strip, seamless tube, rod, bar, wire, profiles.The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, andthe delivery conditions are also specified.This European Standard applies to the wrought copper products as delivered to the device manufacturer, i.e. forfurther fabrication.2
Normative referencesThis European Standard incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references, the latest edition of thepublication referred to applies (including amendments).EN 1655,
Copper and copper alloys — Declarations of conformity.EN 1976,
Copper and copper alloys — Cast unwrought copper products.EN 10002-1,
Metallic materials — Tensile testing — Part 1: Method of test (at ambient temperature).EN 10204,
Metallic materials — Types of inspection documents.EN 13599,
Copper and copper alloys — Copper plate, sheet and strip for electrical purposes.EN 13600,
Copper and copper alloys — Seamless copper tubes for electrical purposes.EN 13601,
Copper and copper alloys — Copper rod, bar and wire for general electrical purposes.EN 13602,
Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical conductors.EN 13605,
Copper and copper alloys — Copper profiles and profiled wire for electrical purposes.EN ISO 2624,
Copper and copper alloys — Estimation of average grain size (ISO 2624:1990).EN ISO 2626,
Copper — Hydrogen embrittlement test (ISO 2626:1973).EN ISO 6506-1,
Metallic materials — Brinell hardness test — Part 1: Test method (ISO 6506-1:1999).EN ISO 6507-1,
Metallic materials — Vickers hardness test — Part 1: Test method (ISO 6507-1:1997).EN ISO 7438,
Metallic materials — Bend test (ISO 7438:1985).IEC 60468,
Method of measurement of resistivity of metallic materials.ISO
1811-2,
Copper and copper alloys — Selection and preparation of samples for chemical analysis —Part 2: Sampling of wrought products and castings.ISO 4746,
Oxygen-free copper — Scale adhesion test.ISO 7801,
Metallic materials — Wire — Reverse bend test.NOTE
Informative references to documents used in the preparation of this standard, and cited at the appropriate places in thetext, are listed in the bibliography.4SIST EN 13604:2004
EN 13604:2002 (E)3
Terms and definitionsFor the purposes of this European Standard, the terms and definitions given in EN 13599, EN 13600, EN 13601,EN 13602 and EN 13605 apply.4
Designations4.1
Material4.1.1
GeneralThe material is designated either by symbol or number (see Table 1).4.1.2
SymbolThe material symbol designation is based on the designation system given in ISO 1190-1.NOTE
Although material symbol designations used in this standard might be the same as those in other standards using thedesignation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same.4.1.3
NumberThe material number designation is in accordance with the system given in EN 1412.4.2
Material conditionFor the purposes of this standard, the following designations, which are in accordance with the system given inEN 1173, apply for the material condition:M Material condition for the product as manufactured without specified mechanical properties;D Material condition for the product as drawn without specified mechanical properties;H.Material condition designated by the minimum value of hardness requirement for the product with mandatoryhardness requirements;R.Material condition designated by the minimum value of tensile strength requirement for the product withmandatory tensile strength requirement (and other tensile property requirements, dependent on product);A.Material condition designated by the minimum value of elongation requirement for the product with mandatoryelongation requirements.NOTE
Products in the H. condition may be specified to Vickers or Brinell hardness, dependent on the product. The materialcondition designation H. is the same for both hardness test methods.Exact conversion between the material conditions designated H. and R., or R. and A., dependent on the product,is not possible.Material condition is designated by only one of the above designations.4.3
ProductThe product designation provides a standardized pattern of designation from which a rapid and unequivocaldescription of a product is conveyed in communication. It provides mutual comprehension at the international levelwith regard to products which meet the requirements of the relevant European Standard.55SIST EN 13604:2004
EN 13604:2002 (E)The product designation is no substitute for the full content of the standard.The product designation for products to this standard shall consist of:– denomination (Plate, Sheet, Strip, Tube, Rod, Bar, Wire Profile or Profiled wire);– number of this European Standard (EN 13604);– material designation, either symbol or number (see Table 1);– other information dependent on copper product for electrical purposes, see 6.2.The derivation of a product designation is shown in example 1 and another typical product designation is shown inexample 2.EXAMPLE 1
Rod for electrical purposes conforming to this standard, in material designated either Cu-OFE or CW009A, inmaterial condition R250, round, nominal diameter 15 mm, tolerance class A, shall be designated as follows:EXAMPLE 2
Strip for electrical purposes conforming to this standard, in material designated either Cu-PHCE or CW022A, inmaterial condition R290, nominal thickness 2 mm, nominal width 1 000 mm, shall be designated as follows:Strip EN 13604 — Cu-PHCE — R290 — 2 x 1 000orStrip EN 13604 — CW022A
— R290 — 2 x 1 0005
Ordering informationIn order to facilitate the enquiry, order and confirmation of order procedures between the purchaser andthe supplier, the purchaser shall state on his enquiry and order the ordering information for the relevantcopper product for electrical purposes from:– plate, sheet and strip in EN 13599;– seamless tubes in EN 13600;– rod, bar and wire in EN 13601;– drawn, round wire in EN 13602;– profiles and profiled wire in EN 13605;6SIST EN 13604:2004
EN 13604:2002 (E)except that the number of this European standard (EN 13604) shall be substituted, or if there is nocorresponding product standard, the details shall be agreed between the purchaser and the supplier. Formaterial conditions other than annealed, the electrical properties shall be agreed between the purchaserand the supplier (see 6.3).In addition the purchaser shall also state on the enquiry and order any of the following, if required:a)dependent on product, test method to be used for the measurement of hardness, i.e. Vickers orBrinell (see 8.3);b)whether scale adhesion test is required for Cu-OFE (CW009A) (see 6.5);c)whether a grain size determination is required (see 6.6);d)whether special surface conditions are required (see 6.8);e)the inspection lot size if different from the sampling rate for mechanical and electrical tests for therelevant copper product from the standards listed above (see 7.3);f)whether a declaration of conformity is required (see 9.1);g)whether an inspection document is required, and if so, which type (see 9.2);h)whether there are any special requirements for marking, packaging or labelling (see clause 10).EXAMPLE
Ordering details for 500 kg rod for electrical purposes conforming to EN 13604, in material designated either Cu-OFEor CW009A, in material condition R250, round, nominal diameter 15 mm, tolerance class A, fixed length 3 000 mm:500 kg Rod EN 13604— Cu-OFE — R250 — RND15A— fixed length 3 000 mmor500 kg Rod EN 13604— CW009A — R250 — RND15A— fixed length 3 000 mm6
Requirements6.1
CompositionThe composition shall conform to the requirements for the appropriate material given in Table 1.NOTE
For characteristics of coppers for electrical purposes, see annex B.6.2
Mechanical propertiesMechanical properties of wrought products made from Cu-OFE (CW009A) and Cu-PHCE (CW022A) shall conformto the mechanical properties specified for:– plate, sheet and strip in EN 13599;– seamless tubes in EN 13600;– rod, bar and wire in EN 13601;– drawn, round wire in EN 13602;– profiles and profiled wire in EN 13605.7SIST EN 13604:2004
EN 13604:2002 (E)In case of hardness requirements, the purchaser shall specify which hardness test (Brinell or Vickers) is mandatory.If there is no corresponding product standard, the properties shall be agreed between the purchaser and thesupplier.The tests shall be carried out in accordance with either 8.2 (tensile test) or 8.3 (hardness test) or 8.4 (bend test).6.3
Electrical
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.