SIST EN 13604:2013
(Main)Copper and copper alloys - Semiconductor devices, electronic and vacuum products made from high conductivity copper
Copper and copper alloys - Semiconductor devices, electronic and vacuum products made from high conductivity copper
This European Standard specifies the composition, property requirements including electrical properties and tolerances on dimensions and form of, semiconductor devices, electronic and vacuum products in two copper grates Cu-OFE (CW009A) and Cu-PHCE (CW022A), in the form of wrought products, e.g. plate, sheet, strip, seamless tube, rod, bar, wire, profiles. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified. This European Standard applies to the wrought copper products as delivered to the device manufacturer, i.e. for further fabrication.
Kupfer und Kupferlegierungen - Produkte aus hochleitfähigem Kupfer für Elektronenröhren, Halbleiterbauelemente und für die Anwendung in der Vakuumtechnik
Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften, einschließlich elektrische Eigenschaften, Grenzabmaße und Formtoleranzen der zwei Kupfersorten Cu-OFE (CW009A) und Cu-PHCE (CW022A), für die Anwendung in der Elektronik, als Halbleiterbauelemente und für die Vakuumtechnik fest, und zwar als Produkte, die durch plastisches Umformen hergestellt wurden, z. B. Platten, Bleche, Bänder, nahtlose Rohre, Stangen, Drähte und Profile.
Der Ablauf der Probenentnahme, die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Europäischen Norm und die Lieferbedingungen sind ebenfalls festgelegt.
Diese Europäische Norm gilt für Produkte aus Kupfer, die durch plastisches Umformen hergestellt wurden, so wie sie an die Hersteller von Bauteilen geliefert werden, d. h. zur weiteren Bearbeitung.
Cuivre et alliages de cuivre - Produits en cuivre de haute conductivité pour application dans les tubes électroniques, semi-conducteurs et vide
La présente Norme européenne spécifie la composition, les caractéristiques, y compris les caractéristiques électriques et les tolérances de dimensions et de forme des dispositifs semi-conducteurs et des produits électroniques et sous vide fabriqués dans deux nuances de cuivre Cu-OFE (CW009A) et Cu-PHCE (CW022A), se présentant sous la forme de produits corroyés, par exemple plaque, tôle, bande, tube sans soudure, barre, fil, profilés.
Les procédures d'échantillonnage, les méthodes d'essai pour la vérification de la conformité aux exigences de la présente norme et les conditions de livraison sont également spécifiées.
La présente Norme européenne s'applique aux produits en cuivre corroyé tels qu'ils sont livrés au fabricant du dispositif, à savoir pour toute fabrication ultérieure.
Baker in bakrove zlitine – Izdelki iz visoko prevodnega bakra za elektronske cevi, polprevodniške sklope in uporabo v vakuumu
Ta evropski standard določa sestavo, zahteve glede značilnosti, vključno z električnimi lastnostmi, ter odstopanja glede dimenzij in oblike za elektronske cevi, polprevodniške sklope in uporabo v vakuumu v bakrenih rešetkah Cu-OFE (CW009A) in Cu-PHCE (CW022A) v obliki gnetenih izdelkov, kot so plošče, ponjave, trakovi, nevarjene cevi, drogovi, palice, žice in profili. Določeni so tudi postopki vzorčenja, preskusne metode za preverjanje skladnosti z zahtevami tega evropskega standarda in dobavni pogoji. Ta evropski standard velja za gnetene bakrene izdelke, ki so dostavljeni proizvajalcu naprav, tj. za nadaljnjo proizvodnjo.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine – Izdelki iz visoko prevodnega bakra za elektronske cevi, polprevodniške sklope in uporabo v vakuumuCopper and copper alloys - Semiconductor devices, electronic and vacuum products made from high conductivity copper77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 13604:2013SIST EN 13604:2013en,de01-september-2013SIST EN 13604:2013SLOVENSKI
STANDARDSIST EN 13604:20041DGRPHãþD
SIST EN 13604:2013
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13604
June 2013 ICS 77.150.30 Supersedes EN 13604:2002English Version
Copper and copper alloys - Semiconductor devices, electronic and vacuum products made from high conductivity copper
Cuivre et alliages de cuivre - Produits en cuivre de haute conductivité pour application dans les tubes électroniques, semi-conducteurs et vide
Kupfer und Kupferlegierungen - Produkte aus hochleitfähigem Kupfer für Elektronenröhren, Halbleiterbauelemente und für die Anwendung in der Vakuumtechnik This European Standard was approved by CEN on 25 April 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13604:2013: ESIST EN 13604:2013
EN 13604:2013 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Terms and definitions .5 4 Designations .5 4.1 Material .5 4.2 Symbol .5 4.3 Number .5 4.4 Material condition .5 4.5 Product .6 5 Ordering information .7 6 Requirements .8 6.1 Composition .8 6.2 Mechanical properties .8 6.3 Electrical properties .8 6.4 Freedom from hydrogen embrittlement .8 6.5 Scale adhesion .9 6.6 Grain size .9 6.7 Tolerances of dimensions and form .9 6.8 Surface condition.9 7 Sampling . 10 7.1 General . 10 7.2 Analysis . 10 7.3 Mechanical, electrical and other tests . 10 8 Test methods . 10 8.1 Analysis . 10 8.2 Tensile test . 11 8.3 Hardness test . 11 8.4 Bend test . 11 8.5 Electrical test . 11 8.6 Hydrogen embrittlement test . 11 8.7 Scale adhesion test . 11 8.8 Estimation of average grain size . 11 8.9 Retests . 12 8.10 Rounding of results . 12 9 Declaration of conformity and inspection documentation . 12 9.1 Declaration of conformity . 12 9.2 Inspection documentation . 12 10 Marking, packaging, labelling . 12 Annex A (normative)
Reference chart for microscopic examination at magnification 100× . 15 Annex B (informative)
Characteristics of coppers for electrical purposes . 16 Bibliography . 18 Figures Figure A.1 — Reference chart for microscopic examination at magnification 100× . 15 Tables Table 1 — Composition of Cu-OFE and Cu-PHCE . 13 Table 2 — Electrical properties (at 20 °C) . 14 Table B.1 — Particular characteristics of coppers for electrical purposes . 17 SIST EN 13604:2013
EN 13604:2013 (E) 3 Foreword This document (EN 13604:2013) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn at the latest by December 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13604:2002. In comparison with EN 13604:2002, the following changes have been made: Normative references have been updated. Editorial modifications have been made. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 4 "Extruded and drawn products, forgings and scrap" to prepare the revision of the following standard: EN 13604:2002, Copper and copper alloys — Products of high conductivity copper for electronic tubes, semi-conductor devices and vacuum applications. The two copper grades Cu-OFE (CW009A) and Cu-PHCE (CW022A) specified in this European Standard are those which are especially suitable for electronic, semiconductor and vacuum applications. Annex A (normative) is the reference for microscopic examination. Annex B (informative) gives guidance on the characteristics of coppers for electrical purposes. This is one of a series of European Standards for copper products for electrical purposes. Other copper products are specified as follows: EN 13599, Copper and copper alloys — Copper plate, sheet and strip for electrical purposes EN 13600, Copper and copper alloys — Seamless copper tubes for electrical purposes EN 13601, Copper and copper alloys — Copper rod, bar and wire for general electrical purposes EN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical conductors EN 13605, Copper and copper alloys — Copper profiles and profiled wire for electrical purposes According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 13604:2013
EN 13604:2013 (E) 4 1 Scope This European Standard specifies the composition, property requirements including electrical properties and tolerances on dimensions and form of semiconductor devices, electronic and vacuum products in two copper grates Cu-OFE (CW009A) and Cu-PHCE (CW022A), in the form of wrought products, e.g. plate, sheet, strip, seamless tube, rod, bar, wire, profiles. The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, and the delivery conditions are also specified. This European Standard applies to the wrought copper products as delivered to the device manufacturer, i.e. for further fabrication. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1655, Copper and copper alloys — Declarations of conformity EN 1976, Copper and copper alloys — Cast unwrought copper products EN 10204, Metallic materials — Types of inspection documents EN 13599, Copper and copper alloys — Copper plate, sheet and strip for electrical purposes EN 13600, Copper and copper alloys — Seamless copper tubes for electrical purposes EN 13601, Copper and copper alloys — Copper rod, bar and wire for general electrical purposes EN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical conductors EN 13605, Copper and copper alloys — Copper profiles and profiled wire for electrical purposes EN ISO 2624, Copper and copper alloys — Estimation of average grain size (ISO 2624) EN ISO 2626, Copper — Hydrogen embrittlement test (ISO 2626) EN ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method (ISO 6506-1) EN ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method (ISO 6507-1) EN ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature (ISO 6892-1) EN ISO 7438, Metallic materials — Bend test (ISO 7438) IEC 60468, Method of measurement of resistivity of metallic materials ISO 1811-2, Copper and copper alloys — Selection and preparation of samples for chemical analysis — Part 2: Sampling of wrought products and castings ISO 4746, Oxygen-free copper — Scale adhesion test ISO 7801, Metallic materials — Wire — Reverse bend test SIST EN 13604:2013
EN 13604:2013 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13599, EN 13600, EN 13601, EN 13602 and EN 13605 apply. 4 Designations 4.1 Material The material is designated either by symbol or by number (see Table 1). 4.2 Symbol The material symbol designation is based on the designation system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the designation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.3 Number The material number designation is in accordance with the system given in EN 1412. 4.4 Material condition The material condition depends on the product and is fully described in the corresponding standards:
EN 13599 for plate, sheet and strip; EN 13600 for tube; EN 13601 for rod and bar; EN 13602 for wire; EN 13605 for profile and profiled wire. For the purposes of this standard, the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: M Material condition for the product as manufactured without specified mechanical properties; D Material condition for the product as drawn without specified mechanical properties; H. Material condition designated by the minimum value of hardness requirement for the product with mandatory hardness requirements; R. Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength requirement (and other tensile property requirements, dependent on product); A. Material condition designated by the minimum value of elongation requirement for the product with manda-tory elongation requirements. Products in the H. condition may be specified to Vickers or Brinell hardness, dependent on the product. The material condition designation H. is the same for both hardness test methods. SIST EN 13604:2013
EN 13604:2013 (E) 6 Exact conversion between the material conditions designated H. and R., or R. and A., dependent on the product, is not possible. Material condition is designated by only one of the above designations. 4.5 Product The product designation provides a standardised pattern of designation from which a rapid and unequivocal description of a product can be conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product designation for products to this standard shall consist of: denomination (Plate, Sheet, Strip, Tube, Rod, Bar, Wire, Profile or Profiled wire); number of this European Standard (EN 13604); material designation, either symbol or number (see Table 1); other information dependent on copper product for electrical purposes (see 6.2). The derivation of a product designation is shown in Example 1 and another typical product designation is shown in Example 2. EXAMPLE 1 Rod for electrical purposes conforming to this standard, in material designated either Cu-OFE or CW009A, in material condition R250, round, nominal diameter 15 mm, tolerance Class A, will be designated as follows:
Rod EN 13604 — Cu-OFE —R250 — RND15A
or
Rod EN 13604 — CW009A —R250 — RND15A Denomination
Number of this European Standard Material designation Material condition designation Cross-sectional shape, nominal dimension in millimetres, tolerance class SIST EN 13604:2013
EN 13604:2013 (E) 7 EXAMPLE 2 Strip for electrical purposes conforming to this standard, in material designated either Cu-PHCE or CW022A, in material condition R290, nominal thickness 2 mm, nominal width 1 000 mm, will be designated as follows:
Strip EN 13604 — Cu-PHCE — R290 — 2 x 1 000
or
Strip EN 13604 — CW022A
— R290 — 2 x 1 000 5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and order the ordering information for the relevant copper product for electrical purposes from:
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.