Fine ceramics (advanced ceramics, advanced technical ceramics) - Reinforcement of ceramic composites - Determination of distribution of tensile strength and tensile strain to failure of filaments within a multifilament tow at ambient temperature (ISO 22459:2024)

This document specifies the conditions for the determination of the distribution of strength and rupture strain of ceramic filaments within a multifilament tow at room temperature by performing a tensile test on a multifilament tow.
This document applies to dry tows of continuous ceramic filaments that are assumed to act freely and independently under loading and exhibit linear elastic behaviour up to failure. The outputs of this method are not to be mixed up with the strengths of embedded tows determined by using ISO 24046[1].
[1] Under preparation.

Hochleistungskeramik - Faserverstärkungen von keramischen Verbundwerkstoffen - Bestimmung der Verteilung von Zugfestigkeit und Zugdehnung bis zum Versagen von Filamenten innerhalb eines Multifilamentkabels bei Raumtemperatur (ISO 22459:2024)

Dieses Dokument legt die Bedingungen für die Bestimmung der Verteilung von Festigkeit und Bruchdehnung von Fasern innerhalb eines Faserbündels bei Raumtemperatur fest, indem ein Zugversuch an einem Faser¬bündel durchgeführt wird.
Dieses Dokument ist anwendbar für unbeschichtete Faserbündel aus keramischen Endlosfasern, von denen angeno¬mmen wird, dass sie sich unter Beanspruchung frei und unabhängig verhalten und bis zum Bruch ein linear-elastisches Verhalten zeigen. Die Ergebnisse dieses Verfahrens sind nicht mit den Festigkeitswerten von eingebetteten Faserbündeln zu verwechseln, die mithilfe von ISO 24046 bestimmt wurden.

Céramiques techniques - Renfort de céramiques composites - Détermination de la distribution de la résistance en traction et de la déformation à la rupture en traction de filaments dans un fil multifilamentaire à température ambiante (ISO 22459:2024)

Le présent document spécifie les conditions de détermination de la distribution de la résistance et de la déformation à la rupture de filaments céramiques dans un fil multifilamentaire à température ambiante, en réalisant un essai de traction sur un fil multifilamentaire.
Ce document s'applique aux fils secs de filaments céramiques continus qui sont supposés se comporter librement et indépendamment sous charge et avoir un comportement linéaire élastique jusqu'à la rupture. Il ne faut pas confondre les résultats de cette méthode avec les résistances de fils imprégnés déterminées à l'aide de l'ISO 24046[1].
[1] En cours d?élaboration.

Fina keramika (sodobna keramika, sodobna tehnična keramika) - Ojačitev keramičnih kompozitov - Ugotavljanje porazdelitve natezne trdnosti in deformacij/obremenitev vlaken v svežnjih pri temperaturi okolice (ISO 22459:2024)

General Information

Status
Published
Public Enquiry End Date
27-May-2024
Publication Date
15-Sep-2024
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Sep-2024
Due Date
11-Nov-2024
Completion Date
16-Sep-2024

Relations

Buy Standard

Standard
EN ISO 22459:2024
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-november-2024
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Ojačitev
keramičnih kompozitov - Ugotavljanje porazdelitve natezne trdnosti in
deformacij/obremenitev vlaken v svežnjih pri temperaturi okolice (ISO 22459:2024)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Reinforcement of
ceramic composites - Determination of distribution of tensile strength and tensile strain to
failure of filaments within a multifilament tow at ambient temperature (ISO 22459:2024)
Hochleistungskeramik - Faserverstärkungen von keramischen Verbundwerkstoffen -
Bestimmung der Verteilung von Zugfestigkeit und Zugdehnung bis zum Versagen von
Filamenten innerhalb eines Multifilamentkabels bei Raumtemperatur (ISO 22459:2024)
Céramiques techniques - Renfort de céramiques composites - Détermination de la
distribution de la résistance en traction et de la déformation à la rupture en traction de
filaments dans un fil multifilamentaire à température ambiante (ISO 22459:2024)
Ta slovenski standard je istoveten z: EN ISO 22459:2024
ICS:
81.060.30 Sodobna keramika Advanced ceramics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 22459
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2024
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes EN ISO 22459:2022
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Reinforcement of ceramic composites -
Determination of distribution of tensile strength and
tensile strain to failure of filaments within a multifilament
tow at ambient temperature (ISO 22459:2024)
Céramiques techniques - Renfort de céramiques Hochleistungskeramik - Faserverstärkungen von
composites - Détermination de la distribution de la keramischen Verbundwerkstoffen - Bestimmung der
résistance en traction et de la déformation à la rupture Verteilung von Zugfestigkeit und Zugdehnung bis zum
en traction de filaments dans un fil multifilamentaire à Versagen von Filamenten innerhalb eines
température ambiante (ISO 22459:2024) Multifilamentkabels bei Raumtemperatur (ISO
22459:2024)
This European Standard was approved by CEN on 30 June 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22459:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 22459:2024) has been prepared by Technical Committee ISO/TC 206 "Fine
ceramics" in collaboration with Technical Committee CEN/TC 184 “Advanced technical ceramics” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2025, and conflicting national standards
shall be withdrawn at the latest by February 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 22459:2022.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 22459:2024 has been approved by CEN as EN ISO 22459:2024 without any modification.

International
Standard
ISO 22459
Second edition
Fine ceramics (advanced ceramics,
2024-08
advanced technical ceramics) —
Reinforcement of ceramic
composites — Determination of
distribution of tensile strength and
tensile strain to failure of filaments
within a multifilament tow at
ambient temperature
Céramiques techniques — Renfort de céramiques composites —
Détermination de la distribution de la résistance en traction et de
la déformation à la rupture en traction de filaments dans un fil
multifilamentaire à température ambiante
Reference number
ISO 22459:2024(en) © ISO 2024
ISO 22459:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 22459:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Significance and use . 2
6 Apparatus . 3
6.1 Tensile testing equipment .3
6.2 Data recording .4
7 Test specimen . 4
7.1 General .4
7.2 Window type specimen .4
7.3 Cylindrical end type specimen .4
8 Test specimen preparation . 5
8.1 General .5
8.2 Window type specimen .5
8.3 Cylindrical end type specimen .6
8.4 Number of test specimens .6
9 Test procedure . 6
9.1 Determination of the initial cross-section area .6
9.2 Determination of the gauge length .6
9.3 Gripping .6
9.4 Selection of strain rate .7
9.5 Test procedure .7
9.6 Determination of load train compliance .7
9.7 Test validity .8
10 Calculation of results . 8
10.1 Calculation of the load train compliance C .8
l
10.2 Calculation of probability of filament rupture P from the tests on specimens with a
j
gauge length of 200 mm .10
10.2.1 Determination of the true origin .10
10.2.2 Construction of envelope curve and determination of instantaneous compliance
C .10
t,j
10.2.3 Probability of filament rupture .11
10.3 Distribution of filament rupture strain .11
10.3.1 Calculation of filament rupture strain .11
10.3.2 Filament rupture strain distribution .11
10.4 Distribution of filam
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.