SIST EN 1007-2:2004

Advanced technical ceramics - Ceramics composites - Methods of test for reinforcement - Part 2: Determination of linear density

This part of EN 1007 specifies a method for the determination of the linear density (mass per unit length) of ceramic fibres, including silicon carbide, silicon nitride, silicon carbon-nitride, alumino-silicate, alumina or silicon oxide fibres. The linear density is determined on unsized ceramic yarn.

Hochleistungskeramik - Keramische Verbunwerkstoffe - Verfahren zur Prüfung der Faserverstärkungen - Teil 2: Bestimmung der Feinheit

Dieser Teil von EN 1007 legt die Bedingungen zur Bestimmung der Feinheit (Masse je Längeneinheit) von keramischen Multifilamentkabeln einschließlich Siliciumcarbid-, Siliciumnitrid-, Silicumcarbonitrid-, Alumo-Silicat-, Aluminiumoxid- und Siliciumdioxidfasern fest.
ANMERKUNG 1   Wenn die Bestimmung der Feinheit an geschlichteten Multifilamentkabeln durchgeführt wird, muss eine Korrektur durch die Berechnung auf der Grundlage des Schlichtegehaltes erfolgen.
ANMERKUNG 2   In dieser Europäischen Norm werden Kohlenstoff-Fasern nicht berücksichtigt. Für Kohlenstoff-Fasern sollte ISO 1889 angewendet werden.

Céramiques techniques avancées - Céramiques composites - Méthodes d'essai pour renforcements - Partie 2: Détermination de la masse linéique

La présente partie de cette Norme européenne spécifie les conditions de détermination de la masse linéique (masse par unité de longueur) des fibres céramiques, dont le carbure de silicium, le nitrure de silicium, le carbonitrure de silicium, le silicate d'alumine, les oxydes d'aluminium ou de silicium.
NOTE 1   Lorsque la détermination de la masse linéique est effectuée sur une éprouvette de fil céramique dimensionné, il convient d'effectuer une correction par calcul en fonction du taux d'ensimage.
NOTE 2   Les fibres de carbone ne sont pas traitées dans la présente Norme européenne. Il convient a cet effet de se référer a l'ISO 1889.

Advanced technical ceramics - Ceramics composites - Methods of test for reinforcement - Part 2: Determination of linear density

General Information

• Status: Published
• Publication Date: 31-Dec-2003
• ICS: 81.060.30 - Advanced ceramics
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Jan-2004
• Due Date: 01-Jan-2004
• Completion Date: 01-Jan-2004
• Mandate: M/BC/CEN/90/4 - Request concerning the realisation of a standardization programme in the field of advanced technical ceramics
• Ref Project: EN 1007-2:2002 - Advanced technical ceramics - Ceramics composites - Methods of test for reinforcement - Part 2: Determination of linear density

Relations

• Replaces: SIST ENV 1007-2:2000 - Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Part 2: Determination of linear density
• Effective Date: 01-Jan-2004

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1007-2:2004
01-januar-2004
Advanced technical ceramics - Ceramics composites - Methods of test for
reinforcement - Part 2: Determination of linear density
Advanced technical ceramics - Ceramics composites - Methods of test for reinforcement
- Part 2: Determination of linear density
Hochleistungskeramik - Keramische Verbunwerkstoffe - Verfahren zur Prüfung der
Faserverstärkungen - Teil 2: Bestimmung der Feinheit
Céramiques techniques avancées - Céramiques composites - Méthodes d'essai pour
renforcements - Partie 2: Détermination de la masse linéique
Ta slovenski standard je istoveten z: EN 1007-2:2002
ICS:
81.060.30 Sodobna keramika Advanced ceramics
SIST EN 1007-2:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 1007-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2002
ICS 81.060.30 Supersedes ENV 1007-2:1993
English version
Advanced technical ceramics - Ceramics composites - Methods
of test for reinforcement - Part 2: Determination of linear density
Céramiques techniques avancées - Céramiques Hochleistungskeramik - Keramische Verbunwerkstoffe -
composites - Méthodes d'essai pour renforcements - Partie Verfahren zur Prüfung der Faserverstärkungen - Teil 2:
2: Détermination de la masse linéique Bestimmung der Feinheit
This European Standard was approved by CEN on 6 July 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1007-2:2002 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 1007-2:2002 (E)
Contents
page
Foreword.3
1 Scope .4
2 Normative references .4
3 Principle.4
4 Terms, definitions and symbols.4
5 Apparatus and accessories .5
6 Sampling.5
7 Testing atmosphere.5
8 Test specimen preparation .5
9 Test procedure .5
10 Calculation of results .5
11 Test report .6
Bibliography .7
2

---------------------- Page: 3 ----------------------

EN 1007-2:2002 (E)
Foreword
This document (EN 1007-2:2002) has been prepared by Technical Committee CEN/TC 184 "Advanced technical
ceramics", the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by March 2003, and conflicting national standards shall be withdrawn at the latest by
March 2003.
This document supersedes ENV 1007-2:1993.
EN 1007 has six parts:
EN 1007-1 Part 1: Determination of size content.
EN 1007-2 Part 2: Determination of linear density.
EN 1007-3 Part 3: Determination of filament diameter and cross-section area.
prEN 1007-4 Part 4: Determination of tensile properties of filament at ambient temperature.
p
...