SIST EN 12697-30:2004
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 30: Specimen preparation by impact compactor
Bituminous mixtures - Test methods for hot mix asphalt - Part 30: Specimen preparation by impact compactor
This European Standard describes methods of moulding specimens from bituminous mixtures by impact compaction. Such specimens are primarily used to determine volumetric density and other technological characteristics e.g. Marshall stability and flow according to EN 12697-34.
This European Standard applies to bituminous mixtures (both those made up in a laboratory and those resulting from work site sampling), with an upper aggregate size not larger than 22,4 mm.
Asphalt - Prüfverfahren für Heißasphalt - Teil 30: Probenvorbereitung, Marshall-Verdichtungsgerät
Diese Europäische Norm beschreibt Verfahren zum Herstellen von Probekörpern aus Asphalt mittels Schlag-verdichtung. Diese Probekörper werden hauptsächlich zur Bestimmung der Raumdichte und anderer techno-logischer Kennwerte, wie z. B. der Marshall-Stabilität und des Marshall-Fließwertes nach EN 12697-34, ver-wendet.
Diese Europäische Norm gilt für Asphalt (sowohl im Labor hergestellte als auch auf der Baustelle entnom-mene Proben) mit einer maximalen Korngröße der Gesteinskörnung von nicht mehr als 22,4 mm.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 30 : Confection d'éprouvettes par compacteur a impact
Cette Norme européenne décrit des méthodes pour mouler des éprouvettes de mélanges bitumineux au moyen d'un compactage par impact. Ce genre d'éprouvettes est principalement utilisé pour déterminer la densité volumétrique et d'autres caractéristiques technologiques, par exemple, la stabilité Marshall et le fluage selon EN 12697-34.
Cette Norme européenne s'applique aux mélanges bitumineux (a la fois confectionnés en laboratoire et provenant de prélevements de chantier), dont la plus grande dimension granulaire n'est pas supérieure 22,4 mm.
Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 30. del: Priprava preskušancev z udarnim zgoščevalnikom
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 30: Specimen preparation by impact compactorMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 30 : Confection d'éprouvettes par compacteur a impactAsphalt - Prüfverfahren für Heißasphalt - Teil 30: Probenvorbereitung, Marshall-VerdichtungsgerätTa slovenski standard je istoveten z:EN 12697-30:2004SIST EN 12697-30:2004en93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-30:200401-september-2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-30June 2004ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part30: Specimen preparation by impact compactorMélanges bitumineux - Méthodes d'essai pour mélangehydrocarboné à chaud - Partie 30 : Confectiond'éprouvettes par compacteur à impactAsphalt - Prüfverfahren für Heißasphalt - Teil 30:Probenvorbereitung, Marshall-VerdichtungsgerätThis European Standard was approved by CEN on 16 April 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-30:2004: E
EN 12697-30:2004 (E) 2 Contents page Foreword.3 1 Scope.6 2 Normative references.6 3 Principle.6 4 Apparatus.6 4.1 Impact compactor with steel anvil.6 4.2 Impact compactor with wooden pedestal.9 4.3 Compaction mould.10 4.4 Ovens or hot plates.10 4.5 Steel block.10 4.6 Shields, baffle plates or sand baths.10 5 Shape and dimensions of the specimens.14 6 Specimen preparation.14 7 Procedure.14 8 Report.15 Annex A (informative)
Device for the measurement of the specimens thickness during compaction.16 Bibliography.17
EN 12697-30:2004 (E) 3 Foreword This document (EN 12697-30:2004) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest by August 2005. Annex A is informative. This document includes a Bibliography. This European Standard is one of a series of standards as listed below: EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test method for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-3, Bituminous mixtures - Test methods for hot mix asphalt - Part 3: Bitumen recovery: Rotary evaporator EN 12697-4, Bituminous mixtures - Test methods for hot mix asphalt - Part 4: Bitumen recovery: Fractionating column EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays EN 12697-8, Bituminous mixtures - Test methods for hot mix asphalt - Part 8: Determination of void characteristics of bituminous specimens EN 12697-9, Bituminous mixtures - Test methods for hot mix asphalt - Part 9: Determination of the reference density EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactability EN 12697-11, Bituminous mixtures - Test methods for hot mix asphalt - Part 11: Determination of the affinity between aggregate and bitumen EN 12697-12, Bituminous mixtures - Test methods for hot mix asphalt - Part 12: Determination of the water sensitivity of bituminous specimens EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous asphalt specimen
EN 12697-30:2004 (E) 4 prEN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or Marshall specimens EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking EN 12697-23, Bituminous mixtures - Test methods for hot mix asphalt - Part 23: Determination of the indirect tensile strength of bituminous specimens EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue prEN 12697-25, Test methods for hot mix asphalt - Part 25: Cyclic compression test prEN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading EN 12697-29, Bituminous mixtures - Test method for hot mix asphalt - Part 29: Determination of the dimensions of a bituminous specimen EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor EN 12697-33, Bituminous mixtures - Test methods for hot mix asphalt - Part 33: Specimen prepared by roller compactor EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness of a bituminous pavement EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the adhesivity of binder on precoated chippings for HRA prEN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and calibration prEN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content by ignition prEN 12697-40, Bituminous mixtures — Test methods for hot mix asphalt — Part 40: In-situ drainability prEN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icing fluids prEN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of foreign matters in reclaimed asphalt prEN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
EN 12697-30:2004 (E) 5 Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 12697-30:2004 (E) 6
1 Scope This European Standard describes methods of moulding specimens from bituminous mixtures by impact compaction. Such specimens are primarily used to determine bulk density and other technological characteristics e.g. Marshall stability and flow according to EN 12697-34. This European Standard applies to bituminous mixtures (both those made up in a laboratory and those resulting from work site sampling), with an upper aggregate size not larger than 22,4 mm. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 12591, Bitumen and bituminous binders – Specifications for paving grade bitumens EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactability EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling prEN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing prEN 13924, Bitumen and bituminous binders – Specifications for hard paving grade bitumens prEN 14023, Bitumen and bituminous binders – Framework specification for poloymer modified bitumens
3 Principle To prepare the specimens, tempered asphalt mix, either freshly mixed according to prEN 12697-35 or sampled on site or plant according to EN 12697-27 is transferred into a specified steel compaction mould. The mixture is then compacted in one of the specified impact compactors by the sliding mass being allowed to fall from a specified height with a specified number of blows within a specified time onto the foot of the hammer, located on top of the asphalt specimen. The specimen is then allowed to cool to room temperature. 4 Apparatus 4.1 Impact compactor with steel anvil 4.1.1 General 4.1.1.1 The impact compactor with steel anvil (see Figure 1), a machine-driven apparatus shall comprise the components listed in 4.1.1.2 to 4.1.1.9. 4.1.1.2 Steel base plate, 15 mm thick and about 600 mm × 610 mm, set horizontally on a firm base. 4.1.1.3 Three feet of equal rigidity in the direction of both compression and shear, fitted with ru
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.