Rolling bearings - Dynamic load ratings and rating life

ISO 281:2007 specifies methods of calculating the basic dynamic load rating of rolling bearings within the size ranges shown in the relevant ISO publications, manufactured from contemporary, commonly used, high quality hardened bearing steel, in accordance with good manufacturing practice and basically of conventional design as regards the shape of rolling contact surfaces.
ISO 281:2007 also specifies methods of calculating the basic rating life, which is the life associated with 90 % reliability, with commonly used high quality material, good manufacturing quality and with conventional operating conditions. In addition, it specifies methods of calculating the modified rating life, in which various reliabilities, lubrication condition, contaminated lubricant and fatigue load of the bearing are taken into account.
ISO 281:2007 does not cover the influence of wear, corrosion and electrical erosion on bearing life.
ISO 281:2007 is not applicable to designs where the rolling elements operate directly on a shaft or housing surface, unless that surface is equivalent in all respects to the bearing ring (or washer) raceway it replaces.

Wälzlager - Dynamische Tragzahlen und nominelle Lebensdauer

Roulements - Charges dynamiques de base et durée nominale

L'ISO 281:2007 spécifie des méthodes de calcul de la charge dynamique de base de roulements appartenant aux plages de dimensions présentées dans les publications ISO correspondantes. Ces roulements sont réputés fabriqués par des méthodes éprouvées, à partir d'un acier trempé de haute qualité, moderne et d'usage habituel pour les roulements, et être de conception classique pour ce qui concerne la forme des surfaces de contact roulantes.
L'ISO 281:2007 spécifie également des méthodes de calcul de la durée nominale de base, c'est-à-dire de la durée associée à une fiabilité de 90 %, à une haute qualité de matériau communément utilisé, à une bonne qualité de fabrication et à des conditions de fonctionnement conventionnelles. En outre, elle spécifie des méthodes de calcul d'une durée nominale modifiée qui prend en compte diverses fiabilités, les conditions de lubrification, l'utilisation de lubrifiant contaminé et la charge de fatigue du roulement.
L'ISO 281:2007 ne couvre pas l'influence de l'usure, de la corrosion et de l'érosion électrique sur la durée des roulements.
L'ISO 281:2007 n'est pas applicable à des conceptions dans lesquelles les éléments roulants portent directement sur la surface d'un arbre ou d'un logement, à moins que cette surface ne soit à tous égards équivalente à celle du chemin de la bague (ou de la rondelle) qu'elle remplace.

Kotalni ležaji - Dinamične nosilnosti in imenska doba trajanja

General Information

Status
Published
Publication Date
10-Jun-2008
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
26-May-2008
Due Date
31-Jul-2008
Completion Date
11-Jun-2008

Relations

Buy Standard

Standard
ISO 281:2008
English language
56 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 281:2007 - Rolling bearings -- Dynamic load ratings and rating life
English language
51 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 281:2007 - Roulements -- Charges dynamiques de base et durée nominale
French language
51 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2008
1DGRPHãþD
SIST ISO 281:2001
SIST ISO/TS 16799:2001
.RWDOQLOHåDML'LQDPLþQHQRVLOQRVWLLQLPHQVNDGREDWUDMDQMD
Rolling bearings - Dynamic load ratings and rating life
Wälzlager - Dynamische Tragzahlen und nominelle Lebensdauer
Roulements - Charges dynamiques de base et durée nominale
Ta slovenski standard je istoveten z: ISO 281:2007
ICS:
21.100.20 Kotalni ležaji Rolling bearings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
STANDARD 281
Second edition
2007-02-15
Rolling bearings — Dynamic load ratings
and rating life
Roulements — Charges dynamiques de base et durée nominale

Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved

Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Symbols . 4
5 Radial ball bearings. 6
5.1 Basic dynamic radial load rating. 6
5.2 Dynamic equivalent radial load . 9
5.3 Basic rating life . 10
6 Thrust ball bearings. 10
6.1 Basic dynamic axial load rating . 10
6.2 Dynamic equivalent axial load. 12
6.3 Basic rating life . 13
7 Radial roller bearings . 13
7.1 Basic dynamic radial load rating. 13
7.2 Dynamic equivalent radial load . 15
7.3 Basic rating life . 16
8 Thrust roller bearings. 16
8.1 Basic dynamic axial load rating . 16
8.2 Dynamic equivalent axial load. 19
8.3 Basic rating life . 19
9 Modified rating life. 20
9.1 General. 20
9.2 Life modification factor for reliability . 20
9.3 Life modification factor for systems approach . 21
Annex A (informative) Detailed method for estimating the contamination factor. 32
Annex B (informative) Calculation of the fatigue load limit . 42
Annex C (informative) Discontinuities in the calculation of basic dynamic load ratings. 47
Bibliography . 51

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 281 was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee SC 8, Load ratings
and life.
This second edition cancels and replaces the first edition (ISO 281:1990), ISO 281:1990/Amd. 1:2000,
ISO 281:1990/Amd. 2:2000 and ISO/TS 16799:1999, which have been technically revised.
iv © ISO 2007 – All rights reserved

Introduction
It is often impractical to establish the suitability of a bearing selected for a specific application by testing a
sufficient number of bearings in that application. However, life, as defined in 3.1, is a primary representation of
the suitability. A reliable life calculation is therefore considered to be an appropriate and convenient substitute
for testing. The purpose of this International Standard is to provide the required basis for life calculation.
Since ISO 281 was published in 1990, additional knowledge has been gained regarding the influence on
bearing life of contamination, lubrication, internal stresses from mounting, stresses from hardening, fatigue
load limit of the material, etc. In ISO 281:1990/Amd. 2:2000, a general method was presented to consider
such influences in the calculation of a modified rating life of a bearing. This amendment is incorporated in this
International Standard, which also provides a practical method to consider the influence on bearing life of
lubrication condition, contaminated lubricant and fatigue load of bearing material.
[1]
ISO/TS 16281 introduced advanced calculation methods which enable the user to take into account the
influence on bearing life of bearing-operating clearance and misalignment under general loading conditions.
The user can also consult the bearing manufacturer for recommendations and evaluation of equivalent load
and life for these operation conditions and other influences as, for example, rolling element centrifugal forces
or other high-speed effects.
Calculations according to this International Standard do not yield satisfactory results for bearings subjected to
such application conditions and/or of such internal design which result in considerable truncation of the area of
contact between the rolling elements and the ring raceways. Unmodified calculation results are thus not
applicable, for example, to ball bearings with filling slots that project substantially into the ball/raceway contact
area when the bearing is subjected to axial loading in the application. Bearing manufacturers should be
consulted in such cases.
The life modification factors for reliability, a , have been slightly changed and extended to 99,95 % reliability.
Revisions of this document will be required from time to time, as the result of new developments or in the light
of new information concerning specific bearing types and materials.
Background information regarding the derivation of equations and factors in this document is given in
1) [2]
ISO/TR 8646 and ISO/TR 1281-2 .

1) Under revision. Will be published under the reference ISO/TR 1281-1.
INTERNATIONAL STANDARD ISO 281:2007(E)

Rolling bearings — Dynamic load ratings and rating life
1 Scope
This International Standard specifies methods of calculating the basic dynamic load rating of rolling bearings
within the size ranges shown in the relevant ISO publications, manufactured from contemporary, commonly
used, high quality hardened bearing steel, in accordance with good manufacturing practice and basically of
conventional design as regards the shape of rolling contact surfaces.
This document also specifies methods of calculating the basic rating life, which is the life associated with 90 %
reliability, with commonly used high quality material, good manufacturing quality and with conventional
operating conditions. In addition, it specifies methods of calculating the modified rating life, in which various
reliabilities, lubrication condition, contaminated lubricant and fatigue load of the bearing are taken into account.
This International Standard does not cover the influence of wear, corrosion and electrical erosion on bearing
life.
This document is not applicable to designs where the rolling elements operate directly on a shaft or housing
surface, unless that surface is equivalent in all respects to the bearing ring (or washer) raceway it replaces.
Double-row radial bearings and double-direction thrust bearings are, when referred to in this document,
presumed to be symmetrical.
Further limitations concerning particular types of bearings are included in the relevant clauses.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 76, Rolling bearings — Static load ratings
ISO 5593, Rolling bearings — Vocabulary
2)
ISO/TR 8646:1985, Explanatory notes on ISO 281/1-1977
ISO 15241, Rolling bearings — Symbols for quantities

2) Under revision. Will be published under the reference ISO/TR 1281-1.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5593 and the following apply.
3.1
life
〈of an individual rolling bearing〉 number of revolutions which one of the bearing rings or washers makes in
relation to the other ring or washer before the first evidence of fatigue develops in the material of one of the
rings or washers or one of the rolling elements
NOTE Life may also be expressed in number of hours of operation at a given constant speed of rotation.
3.2
reliability
〈in the context of bearing life〉 for a group of apparently identical rolling bearings, operating under the same
conditions, the percentage of the group that is expected to attain or exceed a specified life
NOTE The reliability of an individual rolling bearing is the probability that the bearing will attain or exceed a specified
life.
3.3
rating life
predicted value of life based on a basic dynamic radial load rating or a basic dynamic axial load rating
3.4
basic rating life
rating life associated with 90 % reliability for bearings manufactured with commonly used high quality material,
of good manufa
...


INTERNATIONAL ISO
STANDARD 281
Second edition
2007-02-15
Rolling bearings — Dynamic load ratings
and rating life
Roulements — Charges dynamiques de base et durée nominale

Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved

Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Symbols . 4
5 Radial ball bearings. 6
5.1 Basic dynamic radial load rating. 6
5.2 Dynamic equivalent radial load . 9
5.3 Basic rating life . 10
6 Thrust ball bearings. 10
6.1 Basic dynamic axial load rating . 10
6.2 Dynamic equivalent axial load. 12
6.3 Basic rating life . 13
7 Radial roller bearings . 13
7.1 Basic dynamic radial load rating. 13
7.2 Dynamic equivalent radial load . 15
7.3 Basic rating life . 16
8 Thrust roller bearings. 16
8.1 Basic dynamic axial load rating . 16
8.2 Dynamic equivalent axial load. 19
8.3 Basic rating life . 19
9 Modified rating life. 20
9.1 General. 20
9.2 Life modification factor for reliability . 20
9.3 Life modification factor for systems approach . 21
Annex A (informative) Detailed method for estimating the contamination factor. 32
Annex B (informative) Calculation of the fatigue load limit . 42
Annex C (informative) Discontinuities in the calculation of basic dynamic load ratings. 47
Bibliography . 51

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 281 was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee SC 8, Load ratings
and life.
This second edition cancels and replaces the first edition (ISO 281:1990), ISO 281:1990/Amd. 1:2000,
ISO 281:1990/Amd. 2:2000 and ISO/TS 16799:1999, which have been technically revised.
iv © ISO 2007 – All rights reserved

Introduction
It is often impractical to establish the suitability of a bearing selected for a specific application by testing a
sufficient number of bearings in that application. However, life, as defined in 3.1, is a primary representation of
the suitability. A reliable life calculation is therefore considered to be an appropriate and convenient substitute
for testing. The purpose of this International Standard is to provide the required basis for life calculation.
Since ISO 281 was published in 1990, additional knowledge has been gained regarding the influence on
bearing life of contamination, lubrication, internal stresses from mounting, stresses from hardening, fatigue
load limit of the material, etc. In ISO 281:1990/Amd. 2:2000, a general method was presented to consider
such influences in the calculation of a modified rating life of a bearing. This amendment is incorporated in this
International Standard, which also provides a practical method to consider the influence on bearing life of
lubrication condition, contaminated lubricant and fatigue load of bearing material.
[1]
ISO/TS 16281 introduced advanced calculation methods which enable the user to take into account the
influence on bearing life of bearing-operating clearance and misalignment under general loading conditions.
The user can also consult the bearing manufacturer for recommendations and evaluation of equivalent load
and life for these operation conditions and other influences as, for example, rolling element centrifugal forces
or other high-speed effects.
Calculations according to this International Standard do not yield satisfactory results for bearings subjected to
such application conditions and/or of such internal design which result in considerable truncation of the area of
contact between the rolling elements and the ring raceways. Unmodified calculation results are thus not
applicable, for example, to ball bearings with filling slots that project substantially into the ball/raceway contact
area when the bearing is subjected to axial loading in the application. Bearing manufacturers should be
consulted in such cases.
The life modification factors for reliability, a , have been slightly changed and extended to 99,95 % reliability.
Revisions of this document will be required from time to time, as the result of new developments or in the light
of new information concerning specific bearing types and materials.
Background information regarding the derivation of equations and factors in this document is given in
1) [2]
ISO/TR 8646 and ISO/TR 1281-2 .

1) Under revision. Will be published under the reference ISO/TR 1281-1.
INTERNATIONAL STANDARD ISO 281:2007(E)

Rolling bearings — Dynamic load ratings and rating life
1 Scope
This International Standard specifies methods of calculating the basic dynamic load rating of rolling bearings
within the size ranges shown in the relevant ISO publications, manufactured from contemporary, commonly
used, high quality hardened bearing steel, in accordance with good manufacturing practice and basically of
conventional design as regards the shape of rolling contact surfaces.
This document also specifies methods of calculating the basic rating life, which is the life associated with 90 %
reliability, with commonly used high quality material, good manufacturing quality and with conventional
operating conditions. In addition, it specifies methods of calculating the modified rating life, in which various
reliabilities, lubrication condition, contaminated lubricant and fatigue load of the bearing are taken into account.
This International Standard does not cover the influence of wear, corrosion and electrical erosion on bearing
life.
This document is not applicable to designs where the rolling elements operate directly on a shaft or housing
surface, unless that surface is equivalent in all respects to the bearing ring (or washer) raceway it replaces.
Double-row radial bearings and double-direction thrust bearings are, when referred to in this document,
presumed to be symmetrical.
Further limitations concerning particular types of bearings are included in the relevant clauses.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 76, Rolling bearings — Static load ratings
ISO 5593, Rolling bearings — Vocabulary
2)
ISO/TR 8646:1985, Explanatory notes on ISO 281/1-1977
ISO 15241, Rolling bearings — Symbols for quantities

2) Under revision. Will be published under the reference ISO/TR 1281-1.
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 5593 and the following apply.
3.1
life
〈of an individual rolling bearing〉 number of revolutions which one of the bearing rings or washers makes in
relation to the other ring or washer before the first evidence of fatigue develops in the material of one of the
rings or washers or one of the rolling elements
NOTE Life may also be expressed in number of hours of operation at a given constant speed of rotation.
3.2
reliability
〈in the context of bearing life〉 for a group of apparently identical rolling bearings, operating under the same
conditions, the percentage of the group that is expected to attain or exceed a specified life
NOTE The reliability of an individual rolling bearing is the probability that the bearing will attain or exceed a specified
life.
3.3
rating life
predicted value of life based on a basic dynamic radial load rating or a basic dynamic axial load rating
3.4
basic rating life
rating life associated with 90 % reliability for bearings manufactured with commonly used high quality material,
of good manufacturing quality, and operating under conventional operating conditions
3.5
modified rating life
rating life modified for 90 % or other reliability, bearing fatigue load, and/or special bearing properties, and/or
contaminated lubricant, and/or other non-conventional operating conditions
NOTE The term “modified rating life” is new in this document and replaces “adjusted rating life”.
3.6
basic dynamic radial load rating
constant stationary radial load which a rolling bearing can theoretically endure for a basic rating life of one
million revolutions
NOTE In the case of a single-row angular contact bearing, the radial load rati
...


NORME ISO
INTERNATIONALE 281
Deuxième édition
2007-02-15
Roulements — Charges dynamiques de
base et durée nominale
Rolling bearings — Dynamic load ratings and rating life

Numéro de référence
©
ISO 2007
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.

©  ISO 2007
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2007 – Tous droits réservés

Sommaire Page
Avant-propos. iv
Introduction . v
1 Domaine d'application. 1
2 Références normatives . 1
3 Termes et définitions. 2
4 Symboles . 4
5 Roulements radiaux à billes . 6
5.1 Charge radiale dynamique de base . 6
5.2 Charge radiale dynamique équivalente. 9
5.3 Durée nominale de base . 10
6 Butées à billes. 10
6.1 Charge axiale dynamique de base. 10
6.2 Charge axiale dynamique équivalente. 12
6.3 Durée nominale de base . 13
7 Roulements radiaux à rouleaux . 13
7.1 Charge radiale dynamique de base . 13
7.2 Charge radiale dynamique équivalente.15
7.3 Durée nominale de base . 16
8 Butées à rouleaux. 16
8.1 Charge axiale dynamique de base. 16
8.2 Charge axiale dynamique équivalente. 19
8.3 Durée nominale de base . 19
9 Durée nominale corrigée. 20
9.1 Généralités . 20
9.2 Facteur de correction de durée de fiabilité . 20
9.3 Facteur de correction de durée d'une approche systémique . 21
Annexe A (informative) Méthode détaillée d'estimation du facteur de contamination . 32
Annexe B (informative) Calcul de la limite de charge de fatigue. 42
Annexe C (informative) Discontinuités dans le calcul des charges dynamiques de base. 47
Bibliographie . 51

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 281 a été élaborée par le comité technique ISO/TC 4, Roulements, sous-comité SC 8, Charges de base
et durée.
Cette deuxième édition annule et remplace la première édition (ISO 281:1990) ainsi que
l'ISO 281:1990/Amd. 1:2000, l'ISO 281:1990/Amd. 2:2000 et l'ISO/TS 16799:1999, dont elle constitue une
révision technique.
iv © ISO 2007 – Tous droits réservés

Introduction
Il est souvent peu pratique de vérifier, par un nombre d'essais suffisant, qu'un roulement choisi pour une
application donnée lui convient effectivement. Cependant, la durée, telle que définie en 3.1, est un élément
essentiel de cette adéquation. Un calcul de durée fiable est, par conséquent, considéré comme un substitut
pratique et approprié aux essais. La présente Norme internationale a pour objet de fournir les bases
nécessaires à ce calcul de durée.
Depuis la publication de l'ISO 281 en 1990, des connaissances supplémentaires ont été acquises concernant
l'influence sur la durée des roulements de la contamination, de la lubrification, des contraintes internes dues
au montage, des contraintes dues à la trempe, de la limite de la charge de fatigue du matériau, etc. Dans
l'ISO 281:1990/Amd. 2:2000, une méthode générale permettant de prendre en compte de telles influences
dans le calcul de la durée nominale corrigée d'un roulement a été présentée. Cet amendement est incorporé
dans la présente Norme internationale qui donne, en outre, une méthode pratique permettant de prendre en
compte l'influence sur la durée d'un roulement de l'état de la lubrification, de la contamination du lubrifiant et
de la charge de fatigue du matériau du roulement.
[1]
L'ISO/TS 16281 introduit des méthodes de calcul avancées qui permettent de tenir compte de l'influence sur
la durée d'un roulement du jeu de fonctionnement de ce roulement et de ses défauts d'alignement dans des
conditions de charge générales. L'utilisateur peut également demander au fabricant du roulement des
recommandations et l'évaluation d'une charge équivalente et d'une durée dans ces conditions de
fonctionnement et sous l'effet d'autres influences telles que, par exemple, l'influence des forces centrifuges
qui s'exercent sur les éléments roulants ou d'autres effets d'une vitesse élevée.
Des calculs conduits conformément à la présente Norme internationale ne donnent pas de résultats
satisfaisants pour des roulements dans lesquels, en raison de leur construction interne ou des conditions de
leur utilisation, la surface de contact entre les éléments roulants et les chemins de la bague est fortement
tronquée. De tels calculs n'aboutissent pas sans correction à des résultats applicables, par exemple à des
roulements à billes à encoches de remplissage qui débordent nettement sur cette surface de contact lorsque
le roulement est soumis à une charge axiale dans une application. Il est recommandé de consulter le fabricant
du roulement dans de tels cas.
Les facteurs de correction de durée de fiabilité, a , ont été légèrement modifiés et étendus à une fiabilité de
99,95 %.
De futures révisions du présent document seront nécessaires de temps en temps, en raison de nouvelles
recherches ou de nouveaux résultats applicables à tel ou tel type de roulements ou de matériaux.
Des informations de référence concernant la dérivation des équations et des facteurs dans la présente Norme
1) [2]
internationale sont données dans l'ISO/TR 8646 et l'ISO/TR 1281-2 .

1) En cours de révision. Sera publié sous la référence ISO/TR 1281-1.
NORME INTERNATIONALE ISO 281:2007(F)

Roulements — Charges dynamiques de base et durée nominale
1 Domaine d'application
La présente Norme internationale spécifie des méthodes de calcul de la charge dynamique de base de
roulements appartenant aux plages de dimensions présentées dans les publications ISO correspondantes.
Ces roulements sont réputés fabriqués par des méthodes éprouvées, à partir d'un acier trempé de haute
qualité, moderne et d'usage habituel pour les roulements, et être de conception classique pour ce qui
concerne la forme des surfaces de contact roulantes.
La présente Norme internationale spécifie également des méthodes de calcul de la durée nominale de base,
c'est-à-dire de la durée associée à une fiabilité de 90 %, à une haute qualité de matériau communément
utilisé, à une bonne qualité de fabrication et à des conditions de fonctionnement conventionnelles. En outre,
elle spécifie des méthodes de calcul d'une durée nominale modifiée, qui prend en compte diverses fiabilités,
les conditions de lubrification, l'utilisation de lubrifiant contaminé et la charge de fatigue du roulement.
La présente Norme internationale ne couvre pas l'influence de l'usure, de la corrosion et de l'érosion
électrique sur la durée des roulements.
Elle n'est pas applicable à des conceptions dans lesquelles les éléments roulants portent directement sur la
surface d'un arbre ou d'un logement, à moins que cette surface ne soit à tous égards équivalente à celle du
chemin de la bague (ou de la rondelle) qu'elle remplace.
Les roulements radiaux à deux rangées et les butées à double effet, lorsqu'il en est question dans la présente
Norme internationale, sont réputés symétriques.
D'autres limites particulières à certains types de roulements se trouvent aux articles correspondants.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 76, Roulements — Charges statiques de base
ISO 5593, Roulements — Vocabulaire
2)
ISO/TR 8646:1985, Notes explicatives sur l'ISO 281/1-1977
ISO 15241, Roulements — Symboles relatifs aux grandeurs

2) En cours de révision. Sera publié sous la référence ISO/TR 1281-1.
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 5593 ainsi que les
suivants s'appliquent.
3.1
durée
〈pour un roulement considéré isolément〉 nombre de tours que l'une de ses bagues (ou rondelles s'il s'agit
d'une butée) effectue par rapport à l'autre avant l'apparition du premier signe de fatigue de la matière de l'une
des bagues (ou rondelles) ou de l'un des éléments roulants
NOTE La durée peut également être exprimée en nombre d'heures de fonctionnement à une vitesse de rotation
constante donnée.
3.2
fiabilité
〈dans le contexte de la durée d'un roulement〉 pour un groupe de roulements apparemment identiques et
fonctionnant dans l
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.