SIST EN ISO 2376:2010
(Main)Anodizing of aluminium and its alloys - Determination of electric breakdown potential (ISO 2376:2010)
Anodizing of aluminium and its alloys - Determination of electric breakdown potential (ISO 2376:2010)
This International Standard describes methods of test for the determination of the electrical breakdown potential of anodic oxidation coatings on aluminium and its alloys on flat or near-flat surfaces and on round wire. The methods are applicable to anodic oxidation coatings used primarily as electrical insulators. The methods are not applicable to coatings in the vicinity of cut edges, the edges of holes, or sharp changes of angle on, for example, extruded shapes.
Anodisieren von Aluminium und Aluminiumlegierungen - Bestimmung der elektrischen Durchschlagspannung (ISO 2376:2010)
Diese Internationale Norm legt Prüfverfahren zur Bestimmung der elektrischen Durchschlagspannung für
anodisch erzeugte Oxidschichten auf Aluminium und Aluminiumlegierungen auf flachen oder nahezu flachen
Oberflächen und auf Runddraht fest. Die Verfahren sind auf anodisch erzeugte Oxidschichten anwendbar, die
hauptsächlich als elektrische Isolatoren verwendet werden.
Die Verfahren sind nicht auf Schichten in der Nähe von Schnittkanten, Lochkanten oder scharfkantigen Winkelübergängen,
z. B. an Strangpressprofilen, anwendbar.
ANMERKUNG 1 Für unverdichtete Schichten liefern die beschriebenen Verfahren keine zufriedenstellenden Ergebnisse.
ANMERKUNG 2 Die elektrische Durchschlagspannung wird durch die relative Feuchte beeinflusst.
Anodisation de l'aluminium et de ses alliages - Détermination de la tension électrique de claquage (ISO 2376:2010)
L'ISO 2376:2010 spécifie des méthodes d'essai relatives à la détermination de la tension électrique de claquage des couches anodiques de l'aluminium et de ses alliages, sur des surfaces planes ou quasi planes ainsi que sur les fils de section circulaire. Ces méthodes s'appliquent aux couches anodiques utilisées principalement comme isolants électriques.
Ces méthodes ne s'appliquent pas aux couches au voisinage des surfaces de coupe, des bords de trous ou des changements d'angles vifs des profilés filés, par exemple.
Anodizacija aluminija in aluminijevih zlitin - Ugotavljanje električne prebojne napetosti (ISO 2376:2010)
Ta mednarodni standard opisuje metode preskusa za ugotavljanje električne prebojne napetosti anodno oksidiranih prevlek na aluminiju in njegovih zlitinah na ravnih ali skoraj ravnih površinah in na okrogli žici. Te metode veljajo za anodno oksidirane prevleke, ki se uporabljajo predvsem kot električni izolatorji. Te metode ne veljajo za prevleke v bližini odrezanih robov, robov lukenj in ostrih sprememb kota, kot so na primer na ekstrudiranih oblikah.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Anodisieren von Aluminium und Aluminiumlegierungen - Bestimmung der elektrischen Durchschlagspannung (ISO 2376:2010)Anodisation de l'aluminium et de ses alliages - Détermination de la tension électrique de claquage (ISO 2376:2010)Anodizing of aluminium and its alloys - Determination of electric breakdown potential (ISO 2376:2010)77.120.10Aluminij in aluminijeve zlitineAluminium and aluminium alloys25.220.20Površinska obdelavaSurface treatmentICS:Ta slovenski standard je istoveten z:EN ISO 2376:2010SIST EN ISO 2376:2010en,fr01-oktober-2010SIST EN ISO 2376:2010SLOVENSKI
STANDARDSIST EN 12373-17:20021DGRPHãþD
SIST EN ISO 2376:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 2376
August 2010 ICS 25.220.20 Supersedes EN 12373-17:2001English Version
Anodizing of aluminium and its alloys - Determination of electric breakdown potential (ISO 2376:2010)
Anodisation de l'aluminium et de ses alliages - Détermination de la tension électrique de claquage (ISO 2376:2010)
Anodisieren von Aluminium und Aluminiumlegierungen - Bestimmung der elektrischen Durchschlagspannung (ISO 2376:2010) This European Standard was approved by CEN on 14 July 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 2376:2010: ESIST EN ISO 2376:2010
EN ISO 2376:2010 (E) 2 Contents Page Foreword .3 SIST EN ISO 2376:2010
EN ISO 2376:2010 (E) 3 Foreword This document (EN ISO 2376:2010) has been prepared by Technical Committee ISO/TC 79 "Light metals and their alloys" in collaboration with Technical Committee CEN/TC 132 “Aluminium and aluminium alloys” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2011, and conflicting national standards shall be withdrawn at the latest by February 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12373-17:2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 2376:2010 has been approved by CEN as a EN ISO 2376:2010 without any modification.
SIST EN ISO 2376:2010
SIST EN ISO 2376:2010
Reference numberISO 2376:2010(E)© ISO 2010
INTERNATIONAL STANDARD ISO2376Second edition2010-08-01Anodizing of aluminium and its alloys — Determination of electric breakdown potential Anodisation de l'aluminium et de ses alliages — Détermination de la tension électrique de claquage
SIST EN ISO 2376:2010
ISO 2376:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2010 – All rights reserved
SIST EN ISO 2376:2010
ISO 2376:2010(E) © ISO 2010 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2376 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee SC 2, Organi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.