SIST EN ISO 6402-2:2004
(Main)Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003)
Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 6402-2:2003)
ISO 6402-2:2003 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize ASA, AEPDS and ACS moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350. Other test methods in wide use, or of particular significance to these moulding and extrusion materials, are also included in this part of ISO 6402, as are the designatory properties specified in Part 1.
Kunststoffe - Acrylnitril-Styrol-Acrylat (ASA)-, Acrylnitril-(Ethylen-Propylen-Dien)-Styrol (AEPDS)- und Acrylnitril -(Chloriertes Polyethylen)- Styrol (ACS)-Formmassen - Teil 2: Herstellung von Probekörpen und Bestimmung von Eigenschaften (ISO 6402-2:2003)
1.1 Dieser Teil von ISO 6402 legt die Verfahren zur Herstellung von Probekörpern und die zur Bestimmung der Eigenschaften von Acrylnitril-Styrol-Acrylester (ASA)-, Acrylnitril-(Ethylen-Propylen-Dien)-Styrol (AEPDS)- und Acrylnitril-(Chloriertes Polyethylen)-Styrol (ACS)-Form- und -Extrudiermassen anzuwendenden Prüfver-fahren fest. Anfor-derungen an die Behandlung des Probenmaterials und für das Konditionieren des Probenmaterials vor der Herstel-lung der Probe-körper und der Probekörper vor der Prüfung sind ebenfalls enthalten.
1.2 Verfahren und Bedingungen für die Herstellung der Probekörper und Vorschriften für die Bestimmung der Eigenschaften der Formmassen, aus denen die Probekörper hergestellt werden, sind angegeben. Eigenschaften und Prüfverfahren, die anwendbar und notwendig sind, um ASA-, AEPDS- und ACS-Form- und Extrudiermassen zu charakterisieren, sind aufgelistet.
1.3 Die Eigenschaften wurden aus den in ISO 10350 festgelegten, allgemeinen Prüfverfahren ausgewählt. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Form- und Extrudier-massen, wie die kennzeichnenden Eigenschaften aus Teil 1 dieser Norm, sind in diesen Teil von ISO 6402 aufgenommen.
1.4 Um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten, ist es notwendig, dass die hier festge-legten Bedingungen der Probekörperherstellung und -konditionierung, die Probekörper mit den hier festge-legten Abmessungen sowie die hier festgelegten Prüfverfahren angewendet werden. Die gemessenen Werte müssen nicht notwendigerweise mit denen identisch sein, die bei der Anwendung von Probekörpern anderer Abmessungen oder solchen, die mit anderen Verfahren hergestellt wurden, erhalten werden.
Plastiques - Matériaux pour moulage et extrusion a base d'acrylonitrile-styrene-acrylate (ASA), d'acrylonitrile-(éthylene-propylene-diene)-styrene (AEPDS) et d'acrylonitrile-(polyéthylene chloré)-styrene (ACS) - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 6402-2:2003)
L'ISO 6402-2:2003 spécifie les méthodes de préparation des éprouvettes de matériaux à base d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) pour moulage et extrusion, ainsi que les méthodes de mesurage de leurs propriétés. Sont également données les exigences relatives à la manipulation des matériaux d'essai et au conditionnement tant du matériau d'essai avant le moulage que des éprouvettes préalablement aux essais.
Les modes opératoires et les conditions nécessaires à la préparation des éprouvettes et au mesurage des propriétés des matériaux constituant ces éprouvettes sont précisés. La liste des propriétés et des méthodes d'essais appropriées et nécessaires pour caractériser les matériaux ASA, AEPDS et ACS pour moulage et extrusion est également donnée.
Les propriétés ont été sélectionnées parmi les méthodes générales d'essai traitées dans l'ISO 10350. D'autres méthodes couramment employées ou présentant un intérêt particulier pour ces matériaux pour moulage et extrusion sont également données dans la présente partie de l'ISO 6402, de même que les propriétés de désignation spécifiées dans la Partie 1.
Polimerni materiali - Materiali za oblikovanje in ekstrudiranje iz kopolimerov akrilonitril-stiren-akrilata (ASA), akrilonitril-(etilen-propilen-dien)-stirena (AEPDS) in akrilonitril-(klorirani polietilen)-stirena (ACS) - 2. del: Priprava preskušancev in določanje lastnosti (ISO 6402-2:1994)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6402-2:2004
01-februar-2004
1DGRPHãþD
SIST EN ISO 6402-2:2000
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHL]NRSROLPHURY
DNULORQLWULOVWLUHQDNULODWD $6$ DNULORQLWULO HWLOHQSURSLOHQGLHQ VWLUHQD $(3'6
LQDNULORQLWULO NORULUDQLSROLHWLOHQ VWLUHQD $&6 GHO 3ULSUDYDSUHVNXãDQFHYLQ
GRORþDQMHODVWQRVWL ,62
Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-
styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding
and extrusion materials - Part 2: Preparation of test specimens and determination of
properties (ISO 6402-2:2003)
Kunststoffe - Acrylnitril-Styrol-Acrylat (ASA)-, Acrylnitril-(Ethylen-Propylen-Dien)-Styrol
(AEPDS)- und Acrylnitril -(Chloriertes Polyethylen)- Styrol (ACS)-Formmassen - Teil 2:
Herstellung von Probekörpen und Bestimmung von Eigenschaften (ISO 6402-2:2003)
Plastiques - Matériaux pour moulage et extrusion a base d'acrylonitrile-styrene-acrylate
(ASA), d'acrylonitrile-(éthylene-propylene-diene)-styrene (AEPDS) et d'acrylonitrile-
(polyéthylene chloré)-styrene (ACS) - Partie 2: Préparation des éprouvettes et
détermination des propriétés (ISO 6402-2:2003)
Ta slovenski standard je istoveten z: EN ISO 6402-2:2003
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 6402-2:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6402-2:2004
---------------------- Page: 2 ----------------------
SIST EN ISO 6402-2:2004
EUROPEAN STANDARD
EN ISO 6402-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2003
ICS 83.080.20 Supersedes EN ISO 6402-2:1999
English version
Plastics - Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-
(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-
(chlorinated polyethylene)-styrene (ACS) moulding and
extrusion materials - Part 2: Preparation of test specimens and
determination of properties (ISO 6402-2:2003)
Plastiques - Matériaux pour moulage et extrusion à base Kunststoffe - Acrylnitril-Styrol-Acrylat (ASA)-, Acrylnitril-
d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile- (Ethylen-Propylen-Dien)-Styrol (AEPDS)- und Acrylnitril -
(éthylène-propylène-diène)-styrène (AEPDS) et (Chloriertes Polyethylen)- Styrol (ACS)-Formmassen - Teil
d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) - Partie 2: Herstellung von Probekörpern und Bestimmung von
2: Préparation des éprouvettes et détermination des Eigenschaften (ISO 6402-2:2003)
propriétés (ISO 6402-2:2003)
This European Standard was approved by CEN on 10 November 2003.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2003 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6402-2:2003 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6402-2:2004
EN ISO 6402-2:2003 (E)
CORRECTED 2004-03-03
Foreword
This document (EN ISO 6402-2:2003) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2004, and conflicting national
standards shall be withdrawn at the latest by June 2004.
This document supersedes EN ISO 6402-2:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and
the United Kingdom.
Endorsement notice
The text of ISO 6402-2:2003 has been approved by CEN as EN ISO 6402-2:2003 without any
modifications.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6402-2:2004
EN ISO 6402-2:2003 (E)
Annex ZA
(normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.
Publication Year Title EN/HD Year
ISO 62 1999 Plastics - Determination of water absorption EN ISO 62 1999
ISO 75-2 1993 Plastics - Determination of temperature of EN ISO 75-2 1996
deflection under load - Part 2: Plastics and ebonite
ISO 293 1986 Plastics - Compression moulding test specimens EN ISO 293 2003
of thermoplastic materials
ISO 294-1 1996 Plastics - Injection moulding of test specimens of EN ISO 294-1 1998
thermoplastic materials - Part 1: General
principles, and moulding of multipurpose and bar
test specimens
ISO 306 1994 Plastics - Thermoplastic materials - Determination EN ISO 306 1996
of Vicat softening temperature (VST)
ISO 527-2 1993 Plastics - Determination of tensile properties - Part EN ISO 527-2 1996
2: Test conditions for moulding and extrusion
plastics (including Corr 1:1994)
ISO 527-4 1997 Plastics - Determination of tensile properties - Part EN ISO 527-4 1997
4: Test conditions for isotropic and orthotopic
fibre-reinforced plastic composites
ISO 1133 1997 Plastics - Determination of the melt mass-flow rate EN ISO 1133 1999
(MFR) and the melt volume-flow rate (MVR) of
thermoplastics
ISO 2818 1994 Plastics - Preparation of test specimens by EN ISO 2818 1996
machining
ISO 2897-1 1997 Plastics - Impact-resistant polystyrene (PS-I) EN ISO 2897-1 1999
moulding and extrusion materials - Part 1:
Designation system and basis for specifications
ISO 8256 1990 Plastics - Determination of tensile-impact strength EN ISO 8256 1996
(including Technical Corrigendum 1:1991)
3
---------------------- Page: 5 ----------------------
SIST EN ISO 6402-2:2004
---------------------- Page: 6 ----------------------
SIST EN ISO 6402-2:2004
INTERNATIONAL ISO
STANDARD 6402-2
Second edition
2003-12-01
Plastics — Acrylonitrile-styrene-acrylate
(ASA), acrylonitrile-(ethylene-propylene-
diene)-styrene (AEPDS) and acrylonitrile-
(chlorinated polyethylene)-styrene (ACS)
moulding and extrusion materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Matériaux pour moulage et extrusion à base
d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-(éthylène-
propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène
chloré)-styrène (ACS) —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 6402-2:2003(E)
©
ISO 2003
---------------------- Page: 7 ----------------------
SIST EN ISO 6402-2:2004
ISO 6402-2:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2003 — All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 6402-2:2004
ISO 6402-2:2003(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Conformance . 1
3 Normative references . 1
4 Preparation of test specimens. 3
5 Conditioning of test specimens . 4
6 Determination of properties. 4
Annex A (normative) Determination of the bound-acrylonitrile content in the continuous phase. 7
© ISO 2003 — All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 6402-2:2004
ISO 6402-2:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6402-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This second edition cancels and replaces the first edition (ISO 6402-2:1994), which has been technically
revised.
ISO 6402 consists of the following parts, under the general title Plastics — Acrylonitrile-styrene-acrylate (ASA),
acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene
(ACS) moulding and extrusion materials:
Part 1: Designation system and basis for specifications
Part 2: Preparation of test specimens and determination of properties
iv © ISO 2003 — All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 6402-2:2004
INTERNATIONAL STANDARD ISO 6402-2:2003(E)
Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-
(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-
(chlorinated polyethylene)-styrene (ACS) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and determination of properties
1 Scope
1.1 This part of ISO 6402 specifies the methods of preparation of test specimens and the test methods to
be used in determining the properties of acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-
diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion
materials. Requirements for handling test material and for conditioning both the test material before moulding
and the specimens before testing are given here.
1.2 Procedures and conditions for the preparation of test specimens and pro
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.