SIST EN 17339:2025
(Main)Transportable gas cylinders - Hoop wrapped and fully wrapped carbon composite cylinders and tubes for hydrogen
Transportable gas cylinders - Hoop wrapped and fully wrapped carbon composite cylinders and tubes for hydrogen
This document specifies minimum requirements for the materials, design, construction, prototype testing and routine manufacturing inspections of composite gas cylinders and tubes for compressed hydrogen.
NOTE 1 Unless specified in the text, for the purposes of this document, the word “cylinder” includes tubes.
This document applies to
- fully wrapped composite cylinders (Type 3 and Type 4)
- hoop wrapped cylinders (Type 2)
with carbon fibres intended to be permanently mounted in a frame (e.g. bundle or trailer) with a test pressure of not less than 300 bar, with:
— non-metallic liners (for Type 4) or seamless metallic liners (for Type 2 and Type 3),
— a maximum water capacity of 3 000 l
— a maximum working pressure of 1 000 bar.
— the product of working pressure times water capacity (p x V) not exceeding 1 000 000 bar.l.
NOTE 2 A glass fibre protective layer is sometimes applied to the external surface of the cylinder
Ortsbewegliche Gasflaschen - Vollumwickelte Flaschen und Großflaschen aus Kohlenstoff-Verbundwerkstoffen für Wasserstoff
Dieses Dokument legt Mindestanforderungen an die Werkstoffe, Auslegung, Herstellung, Baumusterprüfung und routinemäßigen Inspektionen während der Herstellung von Composite-Gasflaschen und -Großflaschen für verdichteten Wasserstoff fest.
ANMERKUNG 1 Sofern im Text nicht anders festgelegt, schließt der Begriff „Flasche“ für die Anwendung dieses Dokuments Großflaschen ein.
Dieses Dokument gilt für:
- vollumwickelten Composite-Flaschen (Typ 3 und Typ 4);
- umfangsumwickelte Flaschen (Typ 2);
mit Kohlenstofffasern, die dafür vorgesehen sind, dauerhaft in einen Rahmen (z. B. Bündel oder Anhänger) mit einem Prüfdruck von nicht weniger als 300 bar eingebaut zu werden, mit:
- nichtmetallischen Linern (Typ 4) oder nahtlosen metallischen Linern (für Typ 2 und Typ 3);
- einem maximalen Fassungsraum von 3 000 l;
- einem maximalen Betriebsdruck von 1 000 bar;
- einem Produkt aus Betriebsdruck und Fassungsraum (p × V), das 1 000 000 bar ∙ l nicht überschreitet.
ANMERKUNG 2 Eine Glasfaser-Schutzschicht wird mitunter auf die Außenfläche der Flasche aufgebracht.
Bouteilles à gaz transportables - Bouteilles et tubes frettés et entièrement bobinés en matériaux composites carbones pour l'hydrogène
Le présent document spécifie les exigences minimales relatives aux matériaux, à la conception,
à la construction, aux essais de prototype et aux contrôles courants de production des bouteilles à gaz et tubes en matériaux composites pour l’hydrogène comprimé.
NOTE 1 Sauf mention contraire dans le texte, le terme « bouteille » inclut les tubes pour les besoins du présent document.
Le présent document s’applique aux :
- bouteilles entièrement bobinées en matériaux composites (Type 3 et Type 4) ;
- bouteilles frettées (Type 2) ;
avec des fibres de carbone, destinées à être montées de manière permanente dans un châssis (par exemple, un cadre ou une remorque) avec une pression d’épreuve d’au moins 300 bar et :
- des liners non métalliques (Type 4) ou des liners métalliques sans soudure (pour Type 2 et Type 3) ;
- une contenance maximale en eau de 3 000 l ;
- une pression de service maximale de 1 000 bar ;
- le produit de la pression de service multipliée par la contenance en eau (p × V) ne dépassant pas 1 000 000 bar.l.
NOTE 2 Une couche de protection en fibre de verre est parfois appliquée sur la surface de la bouteille.
Premične plinske jeklenke - Popolnoma obvite in po obodu obvite jeklenke in velike jeklenke za vodik iz kompozitnih materialov z ogljikovimi vlakni
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2025
Nadomešča:
SIST EN 17339:2020
Premične plinske jeklenke - Popolnoma obvite in po obodu obvite jeklenke in
velike jeklenke za vodik iz kompozitnih materialov z ogljikovimi vlakni
Transportable gas cylinders - Hoop wrapped and fully wrapped carbon composite
cylinders and tubes for hydrogen
Ortsbewegliche Gasflaschen - Vollumwickelte Flaschen und Großflaschen aus
Kohlenstoff-Verbundwerkstoffen für Wasserstoff
Bouteilles à gaz transportables - Bouteilles et tubes frettés et entièrement bobinés en
matériaux composites carbones pour l'hydrogène
Ta slovenski standard je istoveten z: EN 17339:2024
ICS:
23.020.35 Plinske jeklenke Gas cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 17339
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2024
EUROPÄISCHE NORM
ICS 23.020.35 Supersedes EN 17339:2020
English Version
Transportable gas cylinders - Hoop wrapped and fully
wrapped carbon composite cylinders and tubes for
hydrogen
Bouteilles à gaz transportables - Bouteilles et tubes Ortsbewegliche Gasflaschen - Vollumwickelte Flaschen
frettés et entièrement bobinés en matériaux und Großflaschen aus Kohlenstoff-Verbundwerkstoffen
composites carbones pour l'hydrogène für Wasserstoff
This European Standard was approved by CEN on 6 October 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 17339:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 8
4 Symbols . 10
5 Design and manufacture . 10
5.1 General requirements . 10
5.2 Liner . 11
5.2.1 Metallic liner . 11
5.2.2 Non-metallic liners . 11
5.2.3 Design drawing . 11
5.2.4 Design of ends . 12
5.2.5 Neck ring. 12
5.3 Composite overwrap . 12
5.3.1 Materials . 12
5.3.2 Winding . 12
5.4 Finished cylinder . 13
5.4.1 Design drawings . 13
5.4.2 Autofrettage . 13
5.4.3 Manufacturing requirements for the finished cylinder . 14
6 Cylinder and material tests . 14
6.1 General . 14
6.2 Requirements and test methods . 14
6.2.1 Test 1 – Composite material tests, including adhesives (where applicable) . 14
6.2.2 Test 2 – Liner material tests . 15
6.2.3 Test 3 – Liner burst test at ambient temperature (for metallic liners only) . 15
6.2.4 Test 4 - Pressure test of finished cylinders at ambient temperature . 16
6.2.5 Test 5 – Cylinder burst test . 16
6.2.6 Test 6 – Resistance to pressure cycles at ambient temperature . 17
6.2.7 Test 7 – Exposure to elevated temperature . 19
6.2.8 Test 8 – Blunt impact test . 19
6.2.9 Test 9 – Flawed cylinder test (only for fully wrapped cylinders) . 21
6.2.10 Test 10 – Extreme temperature cycle test . 22
6.2.11 Test 11 – Fire resistance test. 23
6.2.12 Test 12 – Permeability test of cylinders with non-metallic liners. 24
6.2.13 Test 13 – Torque test for taper threads . 25
6.2.14 Test 14 – Shear stress calculation for parallel threads for steel liners and steel
bosses . 25
6.2.15 Test 15 – Neck strength . 26
6.2.16 Test 16 – Neck ring . 26
6.3 Failure to meet test requirements . 26
6.3.1 Metallic liners . 26
6.3.2 Finished cylinder . 26
7 Conformity evaluation . 27
8 Marking . 27
Annex A (normative) Prototype, design variant and production testing . 29
A.1 General . 29
A.2 Type test . 29
A.2.1 General . 29
A.2.2 Definition of new design . 29
A.2.3 Type test requirements. 30
A.2.4 Type test certificate . 31
A.3 Design variant testing . 34
A.3.1 General . 34
A.3.2 Definition of a design variant . 34
A.3.3 Design variant test requirements . 36
A.3.4 Design variant testing certificate . 36
A.4 Production testing . 39
A.4.1 General . 39
A.4.2 Production test requirements . 39
A.4.3 Liner batch tests and inspections . 39
A.4.4 Composite materials batch tests and inspections . 40
A.4.5 Tests and inspections of the finished cylinder . 40
A.4.6 Batch acceptance certificate . 41
Annex B (informative) Examples of type test and production testing certificates . 42
B.1 Type test certificate – composite cylinders with metallic liners . 42
B.2 Type test certificate – composite cylinders with non-metallic liners . 43
B.3 Design variant approval certificate – composite cylinders with metallic liners
..................................................................................................................................................... 44
B.4 Production test certificate . 45
Annex C (informative) Example of high velocity impact (bullet test) . 47
C.1 Procedure . 47
C.2 Criteria . 47
C.3 Parameters to monitor and record . 47
Bibliography . 48
European foreword
This document (EN 17339:2024) has been prepared by Technical Committee CEN/TC 23
“Transportable gas cylinders”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by May 2025, and conflicting national standards
shall be withdrawn at the latest by May 2025.
Attention is drawn to the possibility that some of the elements of this document may be the
subject of patent rights. CEN shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 17339:2020.
EN 17339:2020: introduction of Type 2 cylinders (hoop wrapped cylinders).
This document has been submitted for reference in:
— the RID and
— the technical annexes of the ADR.
NOTE These regulations take precedence over any clause of this document. It is emphasized that
RID/ADR are being revised regularly at intervals of two years which may lead to temporary non-
compliances with the clauses of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Republic of North
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.