SIST EN 300 296-1 V1.4.1:2013
(Main)Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 1: Technical characteristics and methods of measurement
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 1: Technical characteristics and methods of measurement
The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies. The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech. In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate. The present document is complementary to EN 300 086 [i.7], which covers radio equipment with an internal or external RF connector, for use in the land mobile service. The present document may apply to PMR446 equipment as defined in [i.8]. Note that PMR446 equipment has a requirement to incorporate a receiver and may have requirements for 180 s maximum transmission time and VOX.
Elektromagnetna združljivost in zadeve v zvezi z radijskim spektrom (ERM) - Storitev kopenskih mobilnih komunikacij - Radijska oprema, namenjena predvsem za analogni prenos govora, ki uporablja vgrajeno anteno - 1. del: Tehnične karakteristike in merilne metode
Ta dokument zajema minimalne karakteristike, ki so potrebne za preprečevanje škodljivih motenj in sprejemljivo uporabo frekvenc, ki so na voljo. Ta dokument se uporablja za opremo z vgrajenimi antenami za uporabo v modulacijskih sistemih v storitvi kopenskih mobilnih komunikacij, ki deluje na radijskih frekvencah med 30 MHz in 1000 MHz, ima medkanalske razmike 12,5 kHz, 20 kHz in 25 kHz ter je namenjena predvsem za analogni prenos govora. V tem dokumentu so podane različne zahteve za različne radijske frekvenčne pasove, medkanalske razmike, okoljske pogoje in vrste opreme, kjer je ustrezno. Ta dokument dopolnjuje standard EN 300 086 [i.7], ki zajema radijsko opremo z notranjim ali zunanjim radiofrekvenčnim priključkom za uporabo v storitvi kopenskih mobilnih komunikacij. Lahko se uporablja za opremo PMR446, kot je navedeno v točki [i.8]. Opomba: zahteve za opremo PMR446 vključujejo sprejemnik ter najdaljši čas prenosa 180 sekund in VOX.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Part 1: Technical characteristics and methods of measurement33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 300 296-1 Version 1.4.1SIST EN 300 296-1 V1.4.1:2013en01-november-2013SIST EN 300 296-1 V1.4.1:2013SLOVENSKI
STANDARD
SIST EN 300 296-1 V1.4.1:2013
ETSI EN 300 296-1 V1.4.1 (2013-08) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipment using integral antennas intended primarily for analogue speech; Part 1: Technical characteristics and methods of measurement
European Standard SIST EN 300 296-1 V1.4.1:2013
ETSI ETSI EN 300 296-1 V1.4.1 (2013-08) 2
Reference REN/ERM-TGDMR-302 Keywords analogue, mobile, PMR, radio, speech ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 296-1 V1.4.1:2013
ETSI ETSI EN 300 296-1 V1.4.1 (2013-08) 3 Contents Intellectual Property Rights . 6 Foreword . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 7 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 9 3.3 Abbreviations . 9 4 General . 10 4.1 Selection of equipment for testing purposes . 10 4.2 Mechanical and electrical design . 10 4.2.1 General . 10 4.2.2 Controls . 10 4.2.3 Transmitter shut-off facility . 10 4.2.4 Push-to-talk facility. 10 5 Test conditions, power sources and ambient temperatures . 10 5.1 Normal and extreme test conditions . 10 5.2 Test power source . 11 5.3 Normal test conditions . 11 5.3.1 Normal temperature and humidity . 11 5.3.2 Normal test power source . 11 5.3.2.1 Mains voltage . 11 5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 11 5.3.2.3 Other power sources . 11 5.4 Extreme test conditions . 12 5.4.1 Extreme temperatures . 12 5.4.2 Extreme test source voltages . 12 5.4.2.1 Mains voltage . 12 5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 12 5.4.2.3 Power sources using other types of batteries . 12 5.4.2.4 Other power sources . 12 5.5 Procedure for tests at extreme temperatures . 13 5.5.1 Procedure for equipment designed for continuous transmission. 13 5.5.2 Procedure for equipment designed for intermittent transmission . 13 6 General test conditions . 13 6.1 Test signals . 13 6.2 Receiver mute or squelch facility . 14 6.3 Artificial antenna . 14 6.4 Test sites and general arrangements for radiated measurements . 14 6.5 Arrangement for test signals at the input of the transmitter . 14 6.6 Receiver rated audio output power . 14 6.7 Reference for degradation measurements . 14 6.7.1 Definition . 14 6.7.2 Procedures for measurements using the test fixture . 15 6.7.3 Procedures for measurements using the test site . 15 7 Technical characteristics of the transmitter . 15 7.1 Frequency error . 15 7.1.1 Definition . 15 7.1.2 Method of measurement . 16 7.1.3 Limits . 16 SIST EN 300 296-1 V1.4.1:2013
ETSI ETSI EN 300 296-1 V1.4.1 (2013-08) 4 7.2 Effective radiated power . 16 7.2.1 Definition . 16 7.2.2 Method of measurement . 17 7.2.2.1 Maximum effective radiated power under normal test conditions . 17 7.2.2.2 Average effective radiated power under normal test conditions . 18 7.2.2.3 Method of measurements of maximum and average effective radiated power under extreme test conditions . 19 7.2.3 Limits . 19 7.3 Maximum permissible frequency deviation . 20 7.3.1 Definition . 20 7.3.2 Method of measurement . 20 7.3.2.1 Maximum permissible frequency deviation . 21 7.3.2.2 Response of the transmitter to modulation frequencies above 3 kHz . 21 7.3.3 Limits . 21 7.3.3.1 Maximum permissible frequency deviation . 21 7.3.3.2 Response of the transmitter to modulation frequencies above 3 kHz . 21 7.4 Adjacent and alternate channel power . 22 7.4.1 Definition . 22 7.4.2 Method of measurement . 22 7.4.3 Limits . 24 7.5 Radiated unwanted emissions in the spurious domain . 24 7.5.1 Definition . 24 7.5.2 Method of measurement . 25 7.5.3 Limits . 26 7.6 Voice Operated Transmitter . 27 7.6.1 Definition . 27 7.6.2 Method of measurement . 27 7.6.3 Limits . 27 7.7 Maximum transmission time . 28 7.7.1 Definition . 28 7.7.2 Method of measurement . 28 7.7.3 Limits . 28 8 Technical characteristics of the receiver . 28 8.1 Average usable sensitivity (field strength, speech) . 28 8.1.1 Definition . 28 8.1.2 Methods of measurement . 28 8.1.2.1 Method of measurement under normal test conditions . 28 8.1.2.2 Method of measurement under extreme test conditions . 30 8.1.3 Limits . 30 8.2 Spurious radiations . 31 8.2.1 Definition . 31 8.2.2 Method of measurement . 32 8.2.3 Limits . 33 8.3 Co-channel rejection. 34 8.3.1 Definition . 34 8.3.2 Method of measurement . 34 8.3.3 Limits . 35 8.4 Adjacent channel selectivity . 35 8.4.1 Definition . 35 8.4.2 Method of measurement . 35 8.4.3 Limits . 36 8.5 Spurious response rejection . 36 8.5.1 Definition . 36 8.5.2 Method of measurement . 37 8.5.2.1 Introduction to the method of measurement . 37 8.5.2.2 Measurement arrangement . 38 8.5.2.3 Method of the search . 38 8.5.2.4 Measurement . 39 8.5.3 Limits . 40 8.6 Intermodulation response rejection . 40 8.6.1 Definition . 40 SIST EN 300 296-1 V1.4.1:2013
ETSI ETSI EN 300 296-1 V1.4.1 (2013-08) 5 8.6.2 Method of measurement . 40 8.6.3 Limits . 41 8.6.3.1 Limits for low power equipment . 41 8.6.3.2 Limits for other equipment . 42 8.7 Blocking or desensitization . 42 8.7.1 Definition . 42 8.7.2 Method of measurement . 42 8.7.3 Limits . 43 9 Measurement uncertainty . 44 Annex A (normative): Radiated measurement . 45 A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 45 A.1.1 Anechoic chamber . 45 A.1.2 Anechoic chamber with a conductive ground plane . 46 A.1.3 Open Area Test Site (OATS) . 47 A.1.4 Test antenna . 48 A.1.5 Substitution antenna . 48 A.1.6 Measuring antenna . 49 A.2 Guidance on the use of radiation test sites . 49 A.2.1 Verification of the test site . 49 A.2.2 Preparation of the EUT . 49 A.2.3 Power supplies to the EUT . 49 A.2.4 Volume control setting for analogue speech tests . 49 A.2.5 Range length . 50 A.2.6 Site preparation . 50 A.3 Coupling of signals . 51 A.3.1 General . 51 A.3.2 Data Signals. 51 A.3.3 Speech and analogue signals . 51 A.3.3.1 Acoustic coupler description. 51 A.3.3.2 Calibration . 52 A.4 Test fixture . 52 A.4.1 Description . 52 A.4.2 Calibration . 53 A.4.3 Mode of use . 53 Annex B (normative): Specifications for adjacent channel power measurement arrangements . 54 B.1 Power measuring receiver specification . 54 B.1.1 General . 54 B.1.2 IF filter . 54 B.1.3 Oscillator and amplifier . 56 B.1.4 Attenuation indicator . 56 B.1.5 Level indicators . 56 B.1.5.1 Rms level indicator . 56 B.1.5.2 Peak level indicator . 56 B.2 Spectrum analyzer for adjacent channel power measurement . 56 Annex C (normative): Spectrum Analyzer . 58 C.1 Adjacent Channel Power Measurement . 58 C.2 Unwanted Emissions Measurement . 58 Annex D (normative): Band-stop filter (for SINAD meter) . 59 Annex E (informative): Bibliography . 60 History . 61 SIST EN 300 296-1 V1.4.1:2013
ETSI ETSI EN 300 296-1 V1.4.1 (2013-08) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document is part 1 of a mult
...
ETSI EN 300 296-1 V1.4.1 (2013-08)
European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 1: Technical characteristics and
methods of measurement
---------------------- Page: 1 ----------------------
2 ETSI EN 300 296-1 V1.4.1 (2013-08)
Reference
REN/ERM-TGDMR-302
Keywords
analogue, mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 296-1 V1.4.1 (2013-08)
Contents
Intellectual Property Rights . 6
Foreword . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General . 10
4.1 Selection of equipment for testing purposes . 10
4.2 Mechanical and electrical design . 10
4.2.1 General . 10
4.2.2 Controls . 10
4.2.3 Transmitter shut-off facility . 10
4.2.4 Push-to-talk facility. 10
5 Test conditions, power sources and ambient temperatures . 10
5.1 Normal and extreme test conditions . 10
5.2 Test power source . 11
5.3 Normal test conditions . 11
5.3.1 Normal temperature and humidity . 11
5.3.2 Normal test power source . 11
5.3.2.1 Mains voltage . 11
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 11
5.3.2.3 Other power sources . 11
5.4 Extreme test conditions . 12
5.4.1 Extreme temperatures . 12
5.4.2 Extreme test source voltages . 12
5.4.2.1 Mains voltage . 12
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 12
5.4.2.3 Power sources using other types of batteries . 12
5.4.2.4 Other power sources . 12
5.5 Procedure for tests at extreme temperatures . 13
5.5.1 Procedure for equipment designed for continuous transmission. 13
5.5.2 Procedure for equipment designed for intermittent transmission . 13
6 General test conditions . 13
6.1 Test signals . 13
6.2 Receiver mute or squelch facility . 14
6.3 Artificial antenna . 14
6.4 Test sites and general arrangements for radiated measurements . 14
6.5 Arrangement for test signals at the input of the transmitter . 14
6.6 Receiver rated audio output power . 14
6.7 Reference for degradation measurements . 14
6.7.1 Definition . 14
6.7.2 Procedures for measurements using the test fixture . 15
6.7.3 Procedures for measurements using the test site . 15
7 Technical characteristics of the transmitter . 15
7.1 Frequency error . 15
7.1.1 Definition . 15
7.1.2 Method of measurement . 16
7.1.3 Limits . 16
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 296-1 V1.4.1 (2013-08)
7.2 Effective radiated power . 16
7.2.1 Definition . 16
7.2.2 Method of measurement . 17
7.2.2.1 Maximum effective radiated power under normal test conditions . 17
7.2.2.2 Average effective radiated power under normal test conditions . 18
7.2.2.3 Method of measurements of maximum and average effective radiated power under extreme test
conditions . 19
7.2.3 Limits . 19
7.3 Maximum permissible frequency deviation . 20
7.3.1 Definition . 20
7.3.2 Method of measurement . 20
7.3.2.1 Maximum permissible frequency deviation . 21
7.3.2.2 Response of the transmitter to modulation frequencies above 3 kHz . 21
7.3.3 Limits . 21
7.3.3.1 Maximum permissible frequency deviation . 21
7.3.3.2 Response of the transmitter to modulation frequencies above 3 kHz . 21
7.4 Adjacent and alternate channel power . 22
7.4.1 Definition . 22
7.4.2 Method of measurement . 22
7.4.3 Limits . 24
7.5 Radiated unwanted emissions in the spurious domain . 24
7.5.1 Definition . 24
7.5.2 Method of measurement . 25
7.5.3 Limits . 26
7.6 Voice Operated Transmitter . 27
7.6.1 Definition . 27
7.6.2 Method of measurement . 27
7.6.3 Limits . 27
7.7 Maximum transmission time . 28
7.7.1 Definition . 28
7.7.2 Method of measurement . 28
7.7.3 Limits . 28
8 Technical characteristics of the receiver . 28
8.1 Average usable sensitivity (field strength, speech) . 28
8.1.1 Definition . 28
8.1.2 Methods of measurement . 28
8.1.2.1 Method of measurement under normal test conditions . 28
8.1.2.2 Method of measurement under extreme test conditions . 30
8.1.3 Limits . 30
8.2 Spurious radiations . 31
8.2.1 Definition . 31
8.2.2 Method of measurement . 32
8.2.3 Limits . 33
8.3 Co-channel rejection. 34
8.3.1 Definition . 34
8.3.2 Method of measurement . 34
8.3.3 Limits . 35
8.4 Adjacent channel selectivity . 35
8.4.1 Definition . 35
8.4.2 Method of measurement . 35
8.4.3 Limits . 36
8.5 Spurious response rejection . 36
8.5.1 Definition . 36
8.5.2 Method of measurement . 37
8.5.2.1 Introduction to the method of measurement . 37
8.5.2.2 Measurement arrangement . 38
8.5.2.3 Method of the search . 38
8.5.2.4 Measurement . 39
8.5.3 Limits . 40
8.6 Intermodulation response rejection . 40
8.6.1 Definition . 40
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 296-1 V1.4.1 (2013-08)
8.6.2 Method of measurement . 40
8.6.3 Limits . 41
8.6.3.1 Limits for low power equipment . 41
8.6.3.2 Limits for other equipment . 42
8.7 Blocking or desensitization . 42
8.7.1 Definition . 42
8.7.2 Method of measurement . 42
8.7.3 Limits . 43
9 Measurement uncertainty . 44
Annex A (normative): Radiated measurement . 45
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 45
A.1.1 Anechoic chamber . 45
A.1.2 Anechoic chamber with a conductive ground plane . 46
A.1.3 Open Area Test Site (OATS) . 47
A.1.4 Test antenna . 48
A.1.5 Substitution antenna . 48
A.1.6 Measuring antenna . 49
A.2 Guidance on the use of radiation test sites . 49
A.2.1 Verification of the test site . 49
A.2.2 Preparation of the EUT . 49
A.2.3 Power supplies to the EUT . 49
A.2.4 Volume control setting for analogue speech tests . 49
A.2.5 Range length . 50
A.2.6 Site preparation . 50
A.3 Coupling of signals . 51
A.3.1 General . 51
A.3.2 Data Signals. 51
A.3.3 Speech and analogue signals . 51
A.3.3.1 Acoustic coupler description. 51
A.3.3.2 Calibration . 52
A.4 Test fixture . 52
A.4.1 Description . 52
A.4.2 Calibration . 53
A.4.3 Mode of use . 53
Annex B (normative): Specifications for adjacent channel power measurement
arrangements . 54
B.1 Power measuring receiver specification . 54
B.1.1 General . 54
B.1.2 IF filter . 54
B.1.3 Oscillator and amplifier . 56
B.1.4 Attenuation indicator . 56
B.1.5 Level indicators . 56
B.1.5.1 Rms level indicator . 56
B.1.5.2 Peak level indicator . 56
B.2 Spectrum analyzer for adjacent channel power measurement . 56
Annex C (normative): Spectrum Analyzer . 58
C.1 Adjacent Channel Power Measurement . 58
C.2 Unwanted Emissions Measurement . 58
Annex D (normative): Band-stop filter (for SINAD meter) . 59
Annex E (informative): Bibliography . 60
History . 61
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 296-1 V1.4.1 (2013-08)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 1 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of measurement";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates
Date of adoption of this EN: 13 A
...
Final draft ETSI EN 300 296-1 V1.4.1 (2013-06)
European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Land Mobile Service;
Radio equipment using integral antennas
intended primarily for analogue speech;
Part 1: Technical characteristics and
methods of measurement
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 296-1 V1.4.1 (2013-06)
Reference
REN/ERM-TGDMR-302
Keywords
analogue, mobile, PMR, radio, speech
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 296-1 V1.4.1 (2013-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 General . 10
4.1 Selection of equipment for testing purposes . 10
4.2 Mechanical and electrical design . 10
4.2.1 General . 10
4.2.2 Controls . 10
4.2.3 Transmitter shut-off facility . 10
4.2.4 Push-to-talk facility. 10
5 Test conditions, power sources and ambient temperatures . 10
5.1 Normal and extreme test conditions . 10
5.2 Test power source . 11
5.3 Normal test conditions . 11
5.3.1 Normal temperature and humidity . 11
5.3.2 Normal test power source . 11
5.3.2.1 Mains voltage . 11
5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 11
5.3.2.3 Other power sources . 11
5.4 Extreme test conditions . 12
5.4.1 Extreme temperatures . 12
5.4.2 Extreme test source voltages . 12
5.4.2.1 Mains voltage . 12
5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 12
5.4.2.3 Power sources using other types of batteries . 12
5.4.2.4 Other power sources . 12
5.5 Procedure for tests at extreme temperatures . 13
5.5.1 Procedure for equipment designed for continuous transmission. 13
5.5.2 Procedure for equipment designed for intermittent transmission . 13
6 General test conditions . 13
6.1 Test signals . 13
6.2 Receiver mute or squelch facility . 14
6.3 Artificial antenna . 14
6.4 Test sites and general arrangements for radiated measurements . 14
6.5 Arrangement for test signals at the input of the transmitter . 14
6.6 Receiver rated audio output power . 14
6.7 Reference for degradation measurements . 14
6.7.1 Definition . 14
6.7.2 Procedures for measurements using the test fixture . 15
6.7.3 Procedures for measurements using the test site . 15
7 Technical characteristics of the transmitter . 15
7.1 Frequency error . 15
7.1.1 Definition . 15
7.1.2 Method of measurement . 16
7.1.3 Limits . 16
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 296-1 V1.4.1 (2013-06)
7.2 Effective radiated power . 16
7.2.1 Definition . 16
7.2.2 Method of measurement . 17
7.2.2.1 Maximum effective radiated power under normal test conditions . 17
7.2.2.2 Average effective radiated power under normal test conditions . 18
7.2.2.3 Method of measurements of maximum and average effective radiated power under extreme test
conditions . 19
7.2.3 Limits . 19
7.3 Maximum permissible frequency deviation . 20
7.3.1 Definition . 20
7.3.2 Method of measurement . 20
7.3.2.1 Maximum permissible frequency deviation . 21
7.3.2.2 Response of the transmitter to modulation frequencies above 3 kHz . 21
7.3.3 Limits . 21
7.3.3.1 Maximum permissible frequency deviation . 21
7.3.3.2 Response of the transmitter to modulation frequencies above 3 kHz . 21
7.4 Adjacent and alternate channel power . 22
7.4.1 Definition . 22
7.4.2 Method of measurement . 22
7.4.3 Limits . 24
7.5 Radiated unwanted emissions in the spurious domain . 24
7.5.1 Definition . 24
7.5.2 Method of measurement . 25
7.5.3 Limits . 26
7.6 Voice Operated Transmitter . 27
7.6.1 Definition . 27
7.6.2 Method of measurement . 27
7.6.3 Limits . 27
7.7 Maximum transmission time . 28
7.7.1 Definition . 28
7.7.2 Method of measurement . 28
7.7.3 Limits . 28
8 Technical characteristics of the receiver . 28
8.1 Average usable sensitivity (field strength, speech) . 28
8.1.1 Definition . 28
8.1.2 Methods of measurement . 28
8.1.2.1 Method of measurement under normal test conditions . 28
8.1.2.2 Method of measurement under extreme test conditions . 30
8.1.3 Limits . 30
8.2 Spurious radiations . 31
8.2.1 Definition . 31
8.2.2 Method of measurement . 32
8.2.3 Limits . 33
8.3 Co-channel rejection. 34
8.3.1 Definition . 34
8.3.2 Method of measurement . 34
8.3.3 Limits . 35
8.4 Adjacent channel selectivity . 35
8.4.1 Definition . 35
8.4.2 Method of measurement . 35
8.4.3 Limits . 36
8.5 Spurious response rejection . 36
8.5.1 Definition . 36
8.5.2 Method of measurement . 37
8.5.2.1 Introduction to the method of measurement . 37
8.5.2.2 Measurement arrangement . 38
8.5.2.3 Method of the search . 38
8.5.2.4 Measurement . 39
8.5.3 Limits . 40
8.6 Intermodulation response rejection . 40
8.6.1 Definition . 40
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 296-1 V1.4.1 (2013-06)
8.6.2 Method of measurement . 40
8.6.3 Limits . 41
8.6.3.1 Limits for low power equipment . 41
8.6.3.2 Limits for other equipment . 41
8.7 Blocking or desensitization . 42
8.7.1 Definition . 42
8.7.2 Method of measurement . 42
8.7.3 Limits . 43
9 Measurement uncertainty . 43
Annex A (normative): Radiated measurement . 45
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 45
A.1.1 Anechoic chamber . 45
A.1.2 Anechoic chamber with a conductive ground plane . 46
A.1.3 Open Area Test Site (OATS) . 47
A.1.4 Test antenna . 48
A.1.5 Substitution antenna . 48
A.1.6 Measuring antenna . 49
A.2 Guidance on the use of radiation test sites . 49
A.2.1 Verification of the test site . 49
A.2.2 Preparation of the EUT . 49
A.2.3 Power supplies to the EUT . 49
A.2.4 Volume control setting for analogue speech tests . 49
A.2.5 Range length . 50
A.2.6 Site preparation . 50
A.3 Coupling of signals . 51
A.3.1 General . 51
A.3.2 Data Signals. 51
A.3.3 Speech and analogue signals . 51
A.3.3.1 Acoustic coupler description. 51
A.3.3.2 Calibration . 52
A.4 Test fixture . 52
A.4.1 Description . 52
A.4.2 Calibration . 53
A.4.3 Mode of use . 53
Annex B (normative): Specifications for adjacent channel power measurement
arrangements . 54
B.1 Power measuring receiver specification . 54
B.1.1 General . 54
B.1.2 IF filter . 54
B.1.3 Oscillator and amplifier . 56
B.1.4 Attenuation indicator . 56
B.1.5 Level indicators . 56
B.1.5.1 Rms level indicator . 56
B.1.5.2 Peak level indicator . 56
B.2 Spectrum analyzer for adjacent channel power measurement . 56
Annex C (normative): Spectrum Analyzer . 58
C.1 Adjacent Channel Power Measurement . 58
C.2 Unwanted Emissions Measurement . 58
Annex D (normative): Band-stop filter (for SINAD meter) . 59
Annex E (informative): Bibliography . 60
History . 61
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 296-1 V1.4.1 (2013-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the ETSI standards Two-
step Approval Procedure.
The present document is part 1 of a multi-part deliverable covering the Land Mobile Service; Radio equipment using
integral antennas intended primarily for analogue speech, as identified below:
Part 1: "Technical characteristics and methods of meas
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.