SIST EN ISO 13102:2014
(Main)Geometrical product specifications (GPS) - Dimensional measuring equipment: Electronic digital-indicator gauge - Design and metrological characteristics (ISO 13102:2012)
Geometrical product specifications (GPS) - Dimensional measuring equipment: Electronic digital-indicator gauge - Design and metrological characteristics (ISO 13102:2012)
This International Standard specifies the most important design and metrological characteristics of electronic digital-indicator gauges.
Geometrische Produktspezifikation und -prüfung (GPS) - Längenmessgeräte - Konstruktionsmerkmale und messtechnische Merkmale für elektronische digitale Messuhren (ISO 13102:2012)
Diese Internationale Norm legt die wichtigsten Konstruktionsmerkmale und messtechnischen Merkmale für
digitale Messuhren fest.
Spécification géométrique des produits (GPS) - Instruments de mesurage dimensionnel: Comparateurs à tige rentrante à affichage numérique - Caractéristiques de conception et caractéristiques métrologiques (ISO 13102:2012)
L'ISO 13102:2012 spécifie les caractéristiques de conception et les caractéristiques métrologiques les plus importantes pour les comparateurs à tige rentrante à affichage numérique.
Specifikacija geometrijskih veličin izdelka (GPS) - Oprema za merjenje dolžin: elektronski digitalni instrument - Konstrukcijske in merske značilnosti (ISO 13102:2012)
Ta mednarodni standard določa najpomembnejše konstrukcijske in meroslovne značilnosti elektronskih digitalni instrumentov.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13102:2014
01-julij-2014
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND *36 2SUHPD]DPHUMHQMHGROåLQ
HOHNWURQVNLGLJLWDOQLLQVWUXPHQW.RQVWUXNFLMVNHLQPHUVNH]QDþLOQRVWL ,62
Geometrical product specifications (GPS) - Dimensional measuring equipment:
Electronic digital-indicator gauge - Design and metrological characteristics (ISO
13102:2012)
Geometrische Produktspezifikation und -prüfung (GPS) - Längenmessgeräte -
Konstruktionsmerkmale und messtechnische Merkmale für elektronische digitale
Messuhren (ISO 13102:2012)
Spécification géométrique des produits (GPS) - Instruments de mesurage dimensionnel:
Comparateurs à tige rentrante à affichage numérique - Caractéristiques de conception et
caractéristiques métrologiques (ISO 13102:2012)
Ta slovenski standard je istoveten z: EN ISO 13102:2012
ICS:
17.040.30 Merila Measuring instruments
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
SIST EN ISO 13102:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13102:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 13102:2014
EUROPEAN STANDARD
EN ISO 13102
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2012
ICS 17.040.30
English Version
Geometrical product specifications (GPS) - Dimensional
measuring equipment: Electronic digital-indicator gauge - Design
and metrological characteristics (ISO 13102:2012)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation und -prüfung (GPS) -
Instruments de mesurage dimensionnel: Comparateurs à Längenmessgeräte - Konstruktionsmerkmale und
tige rentrante à affichage numérique - Caractéristiques de messtechnische Merkmale für elektronische digitale
conception et caractéristiques métrologiques (ISO Messuhren (ISO/FDIS 13102:2012)
13102:2012)
This European Standard was approved by CEN on 20 July 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13102:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13102:2014
EN ISO 13102:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13102:2014
EN ISO 13102:2012 (E)
Foreword
This document (EN ISO 13102:2012) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification”, the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2013, and conflicting national standards shall be withdrawn
at the latest by February 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 13102:2012 has been approved by CEN as a EN ISO 13102:2012 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 13102:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 13102:2014
INTERNATIONAL ISO
STANDARD 13102
First edition
2012-08-15
Geometrical product specifications
(GPS) — Dimensional measuring
equipment: Electronic digital-indicator
gauge — Design and metrological
characteristics
Spécification géométrique des produits (GPS) — Instruments de
mesurage dimensionnel: Comparateurs à tige rentrante à affichage
numérique — Caractéristiques de conception et caractéristiques
métrologiques
Reference number
ISO 13102:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 13102:2014
ISO 13102:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13102:2014
ISO 13102:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design characteristics . 1
4.1 General design and nomenclature . 1
4.2 Main dimensions . 3
4.3 Digital indicating display . 4
4.4 Error messages . 4
4.5 Interface . 4
4.6 Protection for field use . 4
4.7 Contact element . 4
4.8 Zero adjustment . 4
4.9 Additional functions . 5
4.10 Design characteristics (manufacturer’s specification) . 5
5 Metrological characteristics . 5
5.1 General . 5
5.2 Maximum permissible error of indication . 5
5.3 Maximum permissible limit . 6
6 Proving of conformance with specification . 6
7 Marking . 6
Annex A (informative) Example of a diagram of errors of indication . 7
Annex B (informative) Data sheet (example) . 8
Annex C (informative) Calibration of metrological characteristics . 9
Annex D (informative) Relation to the GPS matrix model .10
Bibliography .12
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 13102:2014
ISO 13102:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13102 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
iv © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 13102:2014
ISO 13102:2012(E)
Introduction
This International Standard is a Geometrical Product Specification (GPS) standard and is to be regarded as
a general GPS standard (see ISO/TR 14638). It influences chain link 5 of the chain of standards on size and
distance in the general GPS matrix.
The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this
standard is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this standard, and the default
decision rules given in ISO 14253-1 apply to specifications made in accordance with this standard, unless
otherwise indicated.
For more detailed information of the relation of the standard to other standards and the GPS matrix model, see
Annex D.
© ISO 2012 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 13102:2014
---------------------- Page: 12 ----------------------
SIST EN ISO 13102:2014
INTERNATIONAL STANDARD ISO 13102:2012(E)
Geometrical product specifications (GPS) — Dimensional
measuring equipment: Electronic digital-indicator gauge —
Design and metrological characteristics
1 Scope
This International Standard specifies the most important design and metrological characteristics of electronic
digital-indicator gauges.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 14253-1, Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 1: Decision rules for proving conformance or non-conformance with specifications
ISO 14253-2, Geometrical product specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of
measuring equipment and in product verification
ISO 14978:2006, Geometrical product specification (GPS) — General concepts and requirement for GPS
measuring equipment
ISO/IEC Guide 98-3, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in
measurement (GUM:1995)
IEC 60529, Degrees of protection provided by enclosures (IP code)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 14978, and the following apply.
3.1
electronic digital-indicator gauge
measuring instrument in which the axial displacements of a plunger are obtained by a transducer and converted
into an electronic signal by suitable electronic means and transmitted to a physically integrated digital display
4 Design characteristics
4.1 General design and nomenclature
The general design and workmanship shall be such that the performance of the electronic digital-indicator
gauge complies with the requirements of this International Standard.
The design and rigidity of the electronic digital-indicator gauge shall be such that the freedom of movement of
the plunger is not impaired by clamping the stem of the instrument, providing that such clamping is carried out
in a proper manner. Where alternative
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.