iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1366-12:2014/oprA1:2019

(Amendment)

Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork

Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork

This part of EN 1366 specifies a method for determining the fire resistance of non-mechanical fire barriers installed in fire separating elements designed to withstand heat and the passage of smoke and gases at high temperature. This European Standard is used in conjunction with EN 1363 1 and EN 1366 2.
This European Standard is not suitable for testing non-mechanical fire barriers in suspended ceilings without modification.
This European Standard is not suitable for testing fire dampers, see EN 1366 2.
This European Standard is not suitable for testing such products as air transfer grilles, as the pressures and flows involved are different and may cause differing behaviour.

Feuerwiderstandsprüfungen für Installationen - Teil 12: Nichtmechanische Brandschutzverschlüsse für Lüftungsleitungen

Essais de résistance au feu des installations techniques - Partie 12: Barrière résistante au feu non mécanique pour les conduits de ventilation

Le présent document a été élaboré dans le cadre d’un mandat donné au CEN par la Commission Européenne et l’Association Européenne de Libre Échange et vient à l’appui des exigences essentielles de Directives UE.

Preskusi požarne odpornosti servisnih inštalacij - 12. del: Nemehanske požarne pregrade za prezračevalne kanale

General Information

Status
Not Published
Public Enquiry End Date
29-May-2019
ICS
13.220.50 - Fire-resistance of building materials and elements
91.060.40 - Chimneys, shafts, ducts
Technical Committee
POZ - Požarna varnost
Current Stage
98 - Abandoned project (Adopted Project)
Start Date
11-Dec-2019
Due Date
16-Dec-2019
Completion Date
11-Dec-2019
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Mandate
M/117 - Horizontal complement to the mandates to CEN/CENELEC concerning the execution of standardization work for the valuation of construction products and elements in respect of their resistance to fire
Ref Project
EN 1366-12:2014/prA1 - Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork

Relations

Consolidated By
SIST EN 1366-12:2014+A1:2020 - Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork
Effective Date
18-Jan-2023
Amends
SIST EN 1366-12:2014 - Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork
Effective Date
01-May-2019
Consolidated By
SIST EN 1366-12:2014+A1:2020 - Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork
Effective Date
19-Jan-2023

Buy Standard

EN 1366-12:2014/oprA1:2019EN 1366-12:2014/oprA1:2019
PreviousNext
Draft
EN 1366-12:2014/oprA1:2019
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1366-12:2014/oprA1:2019
01-maj-2019
3UHVNXVLSRåDUQHRGSRUQRVWLVHUYLVQLKLQãWDODFLMGHO1HPHKDQVNHSRåDUQH
SUHJUDGH]DSUH]UDþHYDOQHNDQDOH
Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for
ventilation ductwork
Feuerwiderstandsprüfungen für Installationen - Teil 12: Nichtmechanische
Brandschutzverschlüsse für Lüftungsleitungen
Essais de résistance au feu des installations techniques - Partie 12: Barrière résistante
au feu non mécanique pour les conduits de ventilation
Ta slovenski standard je istoveten z: EN 1366-12:2014/prA1
ICS:
13.220.50 Požarna odpornost Fire-resistance of building
gradbenih materialov in materials and elements
elementov
91.060.40 Dimniki, jaški, kanali Chimneys, shafts, ducts
SIST EN 1366-12:2014/oprA1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1366-12:2014/oprA1:2019

---------------------- Page: 2 ----------------------

SIST EN 1366-12:2014/oprA1:2019


DRAFT
EUROPEAN STANDARD
EN 1366-12:2014
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
March 2019
ICS 13.220.50; 91.140.30
English Version

Fire resistance tests for service installations - Part 12:
Non-mechanical fire barrier for ventilation ductwork
Essais de résistance au feu des installations techniques Feuerwiderstandsprüfungen für Installationen - Teil
- Partie 12: Barrière résistante au feu non mécanique 12: Nichtmechanische Brandschutzverschlüsse für
pour les conduits de ventilation Lüftungsleitungen
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 127.

This draft amendment A1, if approved, will modify the European Standard EN 1366-12:2014. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All righ
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1366-10:2022(Main)
Fire resistance tests for service installations - Part 10: Smoke control dampers
EN 1366-10:2022

This document specifies test methods for smoke control dampers to assess their performance under elevated temperature or fire conditions.
It is of note that the smoke control damper to be tested could require testing to EN 1366 2 and that this is for consideration before carrying out these tests.
Smoke control damper tests are used to confirm that the furnace testing requirements of EN 12101 8 are met and EN 12101 8 is for consideration before carrying out these tests.
Smoke control dampers tested to this document are expected to be classified using EN 13501 4 and this document is expected to be considered before carrying out these tests.
To this end, this document is expected to be read in conjunction with EN 12101 8, EN 13501 4, EN 1366 2 and EN 1363 1, the latter giving further details for fire resistance testing.
For installation details, the requirements for smoke extraction ducts are for consideration and these are defined in EN 1366 8 and EN 1366 9.

  • Standard
    100 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15882-2:2022(Main)
Extended application of results from fire resistance tests for service installations - Part 2: Fire dampers
EN 15882-2:2022

This document provides guidance and rules to notified bodies (for fire dampers) allowing them to produce/validate an extended field of application report for fire dampers. This document identifies the parameters that affect the fire resistance of dampers. It also identifies the factors that need to be considered when deciding whether, or by how much, the parameter can be extended when contemplating the fire resistance performance of an untested, or untestable variation in the construction.
This document explains the principles behind how a conclusion on the influence of specific parameters/constructional details relating to the relevant criteria (E, I, S) can be achieved.
This document does not cover dampers used for smoke control.
It is the intention that the application of this document makes it possible to identify which specifications to test to maximize the field of application. Some information on test programmes is given for guidance purposes.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1366-5:2021(Main)
Fire resistance tests for service installations - Part 5: Service ducts and shafts
EN 1366-5:2021

This European Standard specifies a method for determining the fire resistance of horizontal service ducts and vertical service shafts, which pass through walls or floors and enclose pipes and cables. The test examines the behaviour of ducts and shafts exposed to fire from outside and from inside the duct. This European Standard is intended to be read in conjunction with EN 1363-1.
This European Standard does not examine the risk of fire spread as a result of thermal conduction along the piping installed in service ducts or shafts, or thermal conduction through the media these pipes carry. It does not cover the risk of damage produced by thermal elongation or shortening of tubes and cables as a result of fire, or damaged pipe suspensions. This European Standard does not give guidance on how to test one, two or three sided service ducts or shafts.
NOTE   Guidance on testing service ducts and shafts of less than four sides will be covered in the extended field of application rules being developed by CEN/TC 127.
This test is unsuitable for evaluating service ducts with internal barriers at walls and floors.
Whilst the walls of service ducts or shafts tested to this method may provide specified levels of integrity or insulation, testing to this European Standard does not replace the testing of the functional endurance of small electrical cables which is covered in EN 50200.
Fire resistance testing of ducts for air distribution systems is covered in EN 1366-1.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1366-1:2014+A1:2020(Main)
Fire resistance tests for service installations - Part 1: Ventilation ducts
EN 1366-1:2014+A1:2020

This Part of EN 1366 specifies a method for determining the fire resistance of vertical and horizontal ventilation ducts including those access panels, which are integral part of the tested ducts. The test examines the behaviour of ducts exposed to fire from the outside (duct A) and fire inside the duct (duct B). This Standard is used in conjunction with EN1363-1.
Annex A provides general guidance and gives background information.
This European Standard is not applicable to:
a)   ducts whose fire resistance depends on the fire resistance performance of a ceiling or wall(where ducts are located in cavities enclosed by fire-resistant shafts or ceilings);
b)   ducts containing fire dampers at points where they pass through fire separations;
c)   one, two or three sided ducts;
d)   fixing of suspension devices (e.g. anchors) to floors or walls.

  • Standard
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1366-12:2014+A1:2020(Main)
Fire resistance tests for service installations - Part 12: Non-mechanical fire barrier for ventilation ductwork
EN 1366-12:2014+A1:2019

This part of EN 1366 specifies a method for determining the fire resistance of non-mechanical fire barriers installed in fire separating elements designed to withstand heat and the passage of smoke and gases at high temperature. This European Standard is used in conjunction with EN 1363-1 and EN 1366-2.
This European Standard is not suitable for testing non-mechanical fire barriers in suspended ceilings without modification.
This European Standard is not suitable for testing fire dampers, see EN 1366-2.
This European Standard is not suitable for testing such products as air transfer grilles, as the pressures and flows involved are different and may cause differing behaviour.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1366-13:2019(Main)
Fire resistance tests for service installations - Part 13: Chimneys
EN 1366-13:2019

This document specifies a procedure to determine the fire resistance time for chimney constructions
(see normative references), shafts of chimneys or penetration elements as part of a chimney
construction under standardized fire conditions. The test examines the behaviour of chimney products
exposed to fire only from the outside or fire from the outside entering into the chimney. This standard
is used in conjunction with EN 1363-1. In chimneys combustion air supply ducts can also be included.
The standard also applies to such chimneys. Slanted chimneys are not included.
Annex A provides general guidance and background information. This document is not applicable to:
— sootfire resistance conditions;
— accessories unless they are included in the system chimney to be tested;
— one, two or three sided enclosures.
If the pressure inside the chimney can in practice decrease to lower values than - 40 Pa or increase to
higher values than + 5000 Pa it shall be considered that this cannot be covered by the test prescribed
in this standard.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15882-1:2012+A1:2018(Main)
Extended application of results from fire resistance tests for service installations - Part 1: Ducts
EN 15882-1:2011+A1:2017

This European Standard identifies parameters that affect the fire resistance of ducts for
ventilation purposes. It also identifies the factors that need to be considered when deciding
whether, or by how much a parameter can be extended either positively or negatively when
contemplating the fire resistance on an untested variation in the construction.
This European Standard, where applicable, gives guidance on additional tests that are needed to
extend the field of application.
The European Standard gives the principles behind how a conclusion on the influence of specific
parameters/constructional details relating to the relevant criteria (E, I, S) can be achieved.
This European Standard only applies to ducts tested to EN 1366-1. Duct sections for use other
than in fire resisting heating, ventilation and air conditioning (HVAC) systems are not covered
by this European Standard. It does not cover ducts used for smoke control which are tested in
accordance with EN 1366-8 or EN 1366-9.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13501-3:2006+A1:2009(Main)
Fire classification of construction products and building elements - Part 3: Classification using data from fire resistance tests on products and elements used in building service installations: fire resisting ducts and fire dampers
EN 13501-3:2005+A1:2009

This European Standard specifies the procedure for classification of the resistance to fire performance of construction products and building elements used as components of building service installations, using data from fire resistance tests which are within the direct field of application of the relevant test method. Classification on the basis of extended application of test results is also included in the scope of this European Standard.
Products/elements for use in ventilation systems include (excluding smoke and heat exhaust ventilation):
-   fire resisting ducts;
-   fire dampers.
Relevant test methods which have been prepared for these products/elements are listed in Clause 2.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    21 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1366-9:2008(Main)
Fire resistance tests for service installations - Part 9: Single compartment smoke extraction ducts
EN 1366-9:2008

This part of EN 1366 specifies a test method for determining the fire resistance of smoke extraction ducts that are used for single compartment applications only. In such applications, the smoke extraction system is only intended to function up to flashover (typically 600 °C).
This method of test is only suitable for ducts constructed from non-combustible materials (euro class A1 and A2-s1, d0).
It is applicable only to four sided and circular ducts. One, two and three sided ducts are not covered.
This test has been designed to cover horizontal smoke extraction ducts intended for single compartment applications only.
This test method of part 9 is applicable only to smoke extraction ducts that do not pass through into other fire compartments. It represents fire exposure of a developing fire (pre-flashover). For smoke extraction ducts that pass through into other compartments, the method of test described in EN 1366-8 should be used.
The smoke extraction duct is part of the smoke extraction system which also includes smoke control dampers and smoke extract fans.
The method described in this test standard is complex and requires sophisticated instrumentation. It is not recommended therefore to try to test multiple assemblies in this test.

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1366-8:2004(Main)
Fire resistance tests for service installations - Part 8: Smoke extraction ducts
EN 1366-8:2004

This Part of this European Standard specifies a test method for determining the fire resistance of smoke extraction ducts. It is applicable only to smoke extraction ducts that pass through another fire compartment from the fire compartment to be extracted in case of fire. It represents fire exposure of a fully developed fire.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    37 pages
    German language
    sale 10% off
    e-Library read for
    1 day