SIST EN 60384-2:2012

Fixed capacitors for use in electronic equipment - Part 2: Sectional specification: Fixed metallized polyethyleneterephthalate film dielectric d.c. capacitors

IEC 60384-2:2011 applies to fixed capacitors for direct current, with metallized electrodes and polyethylene-terephthalate dielectric for use in electronic equipment. These capacitors may have 'self-healing properties' depending on conditions of use. They are primarily intended for applications where the a.c. component is small with respect to the rated voltage. Two performance grades of capacitors are covered, Grade 1 for long-life application and Grade 2 for general application. Capacitors for electromagnetic interference suppression and surface mount fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors are not included, but are covered by IEC 60384-14 and IEC 60384-19 respectively. This fourth edition cancels and replaces the third edition published in 2005 and contains the following significant technical changes with respect to the previous edition.
- Table 1, Sampling plan together with numbers of permissible non-conformance for qualification approval test, has been adjusted.
- Table 3, Lot-by-lot inspection, has been changed, highlighting assessment level EZ only.
- Table 4, Periodic inspection, has been changed, highlighting assessment level EZ only.
- The preferred values of rated voltages have been updated in conformance with the basic series of preferred values R5 and R10 given in ISO 3.

Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 2: Rahmenspezifikation: Festkondensatoren mit metallisierter Kunststofffolie aus Polyethylen-Terephthalat für Gleichspannung

Condensateurs fixes utilisés dans les équipements électroniques - Partie 2: Spécification intermédiaire: Condensateurs fixes pour courant continu à diélectrique en film de polytéréphtalate d'éthylène métallisé

La CEI 60384-2:2011 s'applique aux condensateurs fixes pour courant continu, avec des électrodes métallisées et des diélectriques en téréphtalate de polyéthylène et utilisés dans des équipements électroniques. Ces condensateurs peuvent posséder des 'propriétés autorégénératrices' selon les conditions d'utilisation. Ils sont principalement destinés aux applications dont la composante de courant alternatif est négligeable par rapport à la tension assignée. Deux classes de performance de condensateurs sont couvertes, la Classe 1 pour des applications longues durées et la Classe 2 pour une application courante. Les condensateurs d'antiparasitage et les condensateurs fixes pour courant continu à diélectrique en film de polytéréphtalate d'éthylène métallisé pour montage en surface n'en font pas partie, mais sont couverts par la CEI 60384-14 et la CEI 60384-19 respectivement. Cette quatrième édition annule et remplace la troisième édition parue en 2005 et inclut les modifications techniques significatives suivantes par rapport à l'édition précédente:
- Le tableau 1, Plan d'échantillonnage avec nombre de non-conformités admissibles pour l'essai d'homologation, a été corrigé.
- Le tableau 3, Contrôle lot par lot, a été modifié, mise en évidence du niveau d'assurance EZ uniquement.
- Le tableau 4, Contrôle périodique, a été modifié, mise en évidence du niveau d'assurance EZ uniquement.
- Les valeurs préférentielles des tensions assignées ont été mises à jour conformément à la série de base des valeurs préférentielles R5 et R10 données dans l'ISO 3.

Fiksni kondenzatorji za uporabo v elektronski opremi - 2. del: Področna specifikacija: nespremenljivi kondenzatorji z dielektrikom iz metalizirane polipropilen-tereftalatne folije za enosmerne napetosti

Ta del standarda IEC 60384 se uporablja za fiksne kondenzatorje za enosmerne napetosti z metaliziranimi elektrodami in polipropilen-tereftalatnim dielektrikom za uporabo v elektronski opremi. Ti kondenzatorji imajo lahko »samoozdravljive lastnosti«, odvisno od pogojev uporabe. Namenjeni so predvsem uporabam, pri katerih je izmenična komponenta majhna glede na nazivno napetost. Zajeta sta dva razreda učinkovitosti kondenzatorjev, tj. razred 1 za dolgotrajno uporabo in razred 2 za splošno uporabo. Kondenzatorji za preprečevanje elektromagnetnih motenj in fiksni kondenzatorji za površinsko namestitev z dielektrikom iz metalizirane polipropilen-tereftalatne folije za enosmerne napetosti niso vključeni, vendar je prva vrsta kondenzatorjev zajeta v standardu IEC 60384-14, druga pa v standardu IEC 60384-19.

General Information

• Status: Withdrawn
• Publication Date: 22-Apr-2012
• Withdrawal Date: 18-Jun-2024
• ICS: 31.060.10 - Fixed capacitors
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 19-Jun-2024
• Due Date: 12-Jul-2024
• Completion Date: 19-Jun-2024
• Ref Project: EN 60384-2:2012 - Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed metallized polyethylene terephthalate film dielectric d.c. capacitors

Relations

• Replaces: SIST EN 60384-2:2006 - Fixed capacitors for use in electronic equipment -- Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors
• Effective Date: 28-Jan-2023
• Replaces: SIST EN 60384-2:2006 - Fixed capacitors for use in electronic equipment -- Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors
• Effective Date: 21-Sep-2010
• Replaced By: SIST EN IEC 60384-2:2021 - Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed metallized polyethylene-terephthalate film dielectric DC capacitors (IEC 60384-2:2021)
• Effective Date: 07-Jun-2022
• Replaced By: SIST EN IEC 60384-2:2021 - Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed metallized polyethylene-terephthalate film dielectric DC capacitors (IEC 60384-2:2021)
• Effective Date: 25-May-2021
• Revised: SIST EN IEC 60384-2:2021 - Fixed capacitors for use in electronic equipment - Part 2: Sectional specification - Fixed metallized polyethylene-terephthalate film dielectric DC capacitors (IEC 60384-2:2021)
• Effective Date: 14-May-2019
• Revised: SIST EN 60384-2:2006 - Fixed capacitors for use in electronic equipment -- Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors
• Effective Date: 06-May-2014

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2012
1DGRPHãþD
SIST EN 60384-2:2006
)LNVQLNRQGHQ]DWRUML]DXSRUDERYHOHNWURQVNLRSUHPLGHO3RGURþQD
VSHFLILNDFLMDQHVSUHPHQOMLYLNRQGHQ]DWRUML]GLHOHNWULNRPL]PHWDOL]LUDQH
SROLSURSLOHQWHUHIWDODWQHIROLMH]DHQRVPHUQHQDSHWRVWL
Fixed capacitors for use in electronic equipment - Part 2: Sectional specification: Fixed
metallized polyethyleneterephthalate film dielectric d.c. capacitors
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 2:
Rahmenspezifikation: Festkondensatoren mit metallisierter Kunststofffolie aus
Polyethylen-Terephthalat für Gleichspannung
Condensateurs fixes utilisés dans les équipements électroniques - Partie 2: Spécification
intermédiaire: Condensateurs fixes pour courant continu à diélectrique en film de
polytéréphtalate d'éthylène métallisé
Ta slovenski standard je istoveten z: EN 60384-2:2012
ICS:
31.060.10 Fiksni kondenzatorji Fixed capacitors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60384-2
NORME EUROPÉENNE
March 2012
EUROPÄISCHE NORM
ICS 31.060.30 Supersedes EN 60384-2:2005

English version
Fixed capacitors for use in electronic equipment -
Part 2: Sectional specification -
Fixed metallized polyethylene terephthalate film dielectric d.c. capacitors
(IEC 60384-2:2011)
Condensateurs fixes utilisés dans les Festkondensatoren zur Verwendung in
équipements électroniques - Geräten der Elektronik -
Partie 2: Spécification intermédiaire - Teil 2: Rahmenspezifikation -
Condensateurs fixes pour courant continu Festkondensatoren mit metallisierter
à diélectrique en film de téréphtalate de Kunststofffolie aus Polyethylen-
polyéthylène métallisé Terephthalat für Gleichspannung
(CEI 60384-2:2011) (IEC 60384-2:2011)

This European Standard was approved by CENELEC on 2012-01-13. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60384-2:2012 E
Foreword
The text of document 40/2129/FDIS, future edition 4 of IEC 60384-2, prepared by IEC TC 40, "Capacitors
and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN 60384-2:2012.

The following dates are fixed:
(dop) 2012-10-13
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-01-13
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60384-2:2005.
– Table 1, Sampling plan together with numbers of permissible non-conformance for qualification
approval test, has been adjusted.
– Table 3, Lot-by-lot inspection, has been changed, highlighting assessment level EZ only.
– Table 4, Periodic inspection, has been changed, highlighting assessment level EZ only.
– The preferred values of rated voltages have been updated in conformance with the basic series of
preferred values R5 and R10 given in ISO 3.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 60384-2:2011 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-1 NOTE  Harmonized as EN 60068-1.
IEC 60384-2-1 NOTE  Harmonized as EN 60384-2-1.
IEC 60384-14 NOTE  Harmonized as EN 60384-14.
IEC 60384-19 NOTE  Harmonized as EN 60384-19.

- 3 - EN 60384-2:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60063 1963 Preferred number series for resistors and - -
+ A1 1967 capacitors
+ A2 1977
IEC 60384-1 2008 Fixed capacitors for use in electronic EN 60384-1 2009
+ corr. November 2008 equipment -
Part 1: Generic specification
IEC 61193-2 2007 Quality assessment systems - EN 61193-2 2007
Part 2: Selection and use of sampling plans
for inspection of electronic components and
packages
ISO 3 1973 Preferred numbers - Series of preferred - -
numbers
IEC 60384-2 ®
Edition 4.0 2011-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fixed capacitors for use in electronic equipment –
Part 2: Sectional specification – Fixed metallized polyethylene terephthalate film
dielectric d.c. capacitors
Condensateurs fixes utilisés dans les équipements électroniques –
Partie 2: Spécification intermédiaire – Condensateurs fixes pour courant continu
à diélectrique en film de téréphtalate de polyéthylène métallisé

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX U
ICS 31.060.30 ISBN 978-2-88912-828-0

– 2 – 60384-2  IEC:2011
CONTENTS
FOREWORD . 4
1 General . 6
1.1 Scope . 6
1.2 Object . 6
1.3 Normative references . 6
1.4 Information to be given in a detail specification . 6
1.5 Terms and definitions . 7
1.6 Marking . 8
2 Preferred ratings and characteristics . 9
2.1 Preferred characteristics . 9
2.2 Preferred values of ratings . 9
3 Quality assessment procedures . 10
3.1 Primary stage of manufacture . 10
3.2 Structurally similar components . 10
3.3 Certified records of released lots . 10
3.4 Qualification approval . 10
3.5 Quality conformance inspection . 17
4 Test and measurement procedures . 19
4.1 Visual examination and check of dimensions . 19
4.2 Electrical tests . 19
4.3 Robustness of terminations . 22
4.4 Resistance to soldering heat . 22
4.5 Solderability . 22
4.6 Rapid change of the temperature . 23
4.7 Vibration. 23
4.8 Bump . 23
4.9 Shock . 24
4.10 Climatic sequence . 24
4.11 Damp heat, steady state . 25
4.12 Endurance . 26
4.13 Charge and discharge . 26
4.14 Component solvent resistance . 27
4.15 Solvent resistance of the marking . 27
Bibliography . 28

Table 1 – Sampling plan together with numbers of permissible non-conformance for
qualification approval test . 12
Table 2 – Test schedule for qualification approval. 13
Table 3 – Lot-by-lot inspection . 18
Table 4 – Periodic inspection . 19
Table 5 – Test points and voltages . 19
Table 6 – Tangent of loss angle requirements . 20
Table 7 – Insulation resistance requirements . 21
Table 8 – Correction factors . 22
Table 9 – Preferred severities . 24

60384-2  IEC:2011 – 3 –
Table 10 – Test conditions . 26
Table 11 – Lead spacing . 27

– 4 – 60384-2  IEC:2011
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 2: Sectional specification – Fixed metallized polyethylene
terephthalate film dielectric d.c. capacitors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions o
...