SIST EN ISO 204:2018

Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2018)

This document specifies the methods for
a) uninterrupted creep tests with continuous monitoring of extension,
b) interrupted creep tests with periodic measurement of elongation,
c) stress rupture tests where normally only the time to fracture is measured,
d) a test to verify that a predetermined time can be exceeded under a given force, with the elongation
or extension not necessarily being reported.
NOTE A creep test can be continued until fracture has occurred or it can be stopped before fracture.

Metallische Werkstoffe - Einachsiger Zeitstandversuch unter Zugbeanspruchung - Prüfverfahren (ISO 204:2018)

Matériaux métalliques - Essai de fluage uniaxial en traction - Méthode d'essai (ISO 204:2018)

Le présent document spécifie les méthodes pour:
a)    les essais de fluage ininterrompu avec surveillance continue de l'extension,
b)    les essais de fluage interrompus avec mesurage périodique de l'allongement,
c)    les essais de rupture sous contrainte lorsque seul le temps jusqu'à la rupture est normalement mesuré,
d)    un essai pour vérifier qu'un temps prédéterminé peut être dépassé sous une force donnée, sans que l'allongement ou l'extension n'ait été nécessairement rapporté.
NOTE       Une essai de fluage peut se poursuivre jusqu'à la rupture effective ou peut être arrêté avant la rupture.

Kovinski materiali - Preskušanje nesoosnega lezenja pri nategu - Metoda preskušanja (ISO 204:2018)

Ta dokument določa metode za:
a) neprekinjene preskuse lezenja z neprekinjenim spremljanjem razširitve,
b) prekinjene preskuse lezenja s periodičnimi meritvami raztezka,
c) preskuse zloma zaradi obremenitve, pri katerih se običajno meri samo čas do preloma,
d) preskus za potrditev, da je mogoče pri dani sili preseči predhodno določeni čas, pri čemer se ne poroča nujno o raztezku ali razširitvi.
OPOMBA: Preskus lezenja je mogoče nadaljevati, dokler ne pride do preloma, mogoče pa ga je tudi ustaviti pred prelomom.

General Information

• Status: Withdrawn
• Publication Date: 15-Nov-2018
• Withdrawal Date: 11-Oct-2023
• ICS: 77.040.10 - Mechanical testing of metals
• Technical Committee: PKG - Testing of metallic materials
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 09-Oct-2023
• Due Date: 01-Nov-2023
• Completion Date: 12-Oct-2023
• Ref Project: EN ISO 204:2018 - Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2018)

Relations

• Replaces: SIST EN ISO 204:2011 - Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2009)
• Effective Date: 08-Jun-2022
• Replaces: SIST EN ISO 204:2011 - Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2009)
• Effective Date: 17-Oct-2018
• Replaced By: SIST EN ISO 204:2023 - Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2023)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 204:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 204:2011
Kovinski materiali - Preskušanje nesoosnega lezenja pri nategu - Metoda
preskušanja (ISO 204:2018)
Metallic materials - Uniaxial creep testing in tension - Method of test (ISO 204:2018)
Metallische Werkstoffe - Einachsiger Zeitstandversuch unter Zugbeanspruchung -
Prüfverfahren (ISO 204:2018)
Matériaux métalliques - Essai de fluage uniaxial en traction - Méthode d'essai (ISO
204:2018)
Ta slovenski standard je istoveten z: EN ISO 204:2018
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 204:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 204:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 204:2018


EN ISO 204
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2018
EUROPÄISCHE NORM
ICS 77.040.10 Supersedes EN ISO 204:2009
English Version

Metallic materials - Uniaxial creep testing in tension -
Method of test (ISO 204:2018)
Matériaux métalliques - Essai de fluage uniaxial en Metallische Werkstoffe - Einachsiger Zeitstandversuch
traction - Méthode d'essai (ISO 204:2018) unter Zugbeanspruchung - Prüfverfahren (ISO
204:2018)
This European Standard was approved by CEN on 12 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 204:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 204:2018
EN ISO 204:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 204:2018
EN ISO 204:2018 (E)
European foreword
This document (EN ISO 204:2018) has been prepared by Technical Committee ISO/TC 164 "Mechanical
testing of metals" in collaboration with Technical Committee ECISS/TC 101 “Test methods for steel
(other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 204:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 204:2018 has been approved by CEN as EN ISO 204:2018 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 204:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 204:2018
INTERNATIONAL ISO
STANDARD 204
Third edition
2018-08
Metallic materials — Uniaxial creep
testing in tension — Method of test
Matériaux métalliques — Essai de fluage uniaxi
...