SIST EN ISO 6507-1:2023
(Main)Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2023)
Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2023)
This document specifies the Vickers hardness test method for the three different ranges of test force for
metallic materials, including hard metals and other cemented carbides (see Table 1), metallic coatings
and other inorganic coatings.
Table 1 — Ranges of test force
Ranges of test force, F
N
Hardness symbol Designation
F ≥ 49,03 ≥HV 5 Vickers hardness test
1,961 ≤ F < 49,03 HV 0,2 to
0,020 mm and 1,400 mm. Using this method to determine Vickers hardness from smaller indentations
is outside the scope of this document as results would suffer from large uncertainties due to the
limitations of optical measurement and imperfections in tip geometry.
The Vickers hardness specified in this document is also applicable for metallic and other inorganic
coatings including electrodeposited coatings, autocatalytic coatings, sprayed coatings and anodic
coatings on aluminium.
This document is applicable to measurements normal to the coated surface and to measurements on
cross-sections, provided that the characteristics of the coating (smoothness, thickness, etc.) permit
accurate readings of the diagonal of the indentation.
This document is not applicable for coatings with thickness less than 0,030 mm when testing normal
to the coating surface. This standard is not applicable for coatings with thickness less than 0,100 mm
when testing a cross-section of the coating. ISO 14577-1 can be used for the determination of hardness
from smaller indentations.”
A periodic verification method is specified for routine checking of the testing machine in service by the
user.
For specific materials and/or products, relevant International Standards exist.
Metallische Werkstoffe – Härteprüfung nach Vickers – Teil1: Prüfverfahren (ISO 6507-1:2023)
Dieses Dokument legt das Verfahren für die Härteprüfung nach Vickers für metallische Werkstoffe, einschließlich Hartmetallen und anderen Sintercarbiden, für drei unterschiedliche Bereiche der Prüfkraft fest (siehe Tabelle 1).
Tabelle 1 — Bereiche der Prüfkraft
Bereiche der Prüfkraft F
N Härtesymbol Benennung
F ≥ 49,03 ≥ HV 5 Härteprüfung nach Vickers
1,961 ≤ F < 49,03 HV 0,2 bis < HV 5 Härteprüfung nach Vickers im Kleinkraftbereich
0,009 807 ≤ F < 1,961 HV 0,001 bis < HV 0,2 Vickers-Mikrohärteprüfung
Die Härteprüfung nach Vickers ist in diesem Dokument für Eindruckdiagonalen mit Längen zwischen 0,020 mm und 1,400 mm festgelegt. Die Anwendung dieses Verfahrens zur Bestimmung der Vickers-Härte (en: Vickers hardness, HV) anhand kleinerer Eindrücke fällt nicht in den Anwendungsbereich dieses Dokuments, da die Ergebnisse aufgrund der Grenzen der optischen Messung und Unregelmäßigkeiten bei der Spitzengeometrie großen Messunsicherheiten unterliegen würden.
Für die Routineüberprüfung der vom Anwender genutzten Prüfmaschine ist ein Verfahren zur regelmäßigen Überprüfung festgelegt.
Für besondere Werkstoffe und/oder Erzeugnisse gibt es spezielle Internationale Normen.
Matériaux métalliques - Essai de dureté Vickers - Partie 1: Méthode d'essai (ISO 6507-1:2023)
L'ISO 6507-1:2018 spécifie la méthode d'essai de dureté Vickers pour les trois plages différentes de force d'essai, pour les matériaux métalliques y compris les métaux durs et autres carbures cimentaires.
Kovinski materiali - Preskus trdote po Vickersu - 1. del: Preskusna metoda (ISO 6507-1:2023)
Ta dokument določa metodo za preskus trdote po Vickersu za tri različne razpone preskusne sile za kovinske materiale, vključno s trdimi kovinami in drugimi cementiranimi karbidi (glej preglednico 1), kovinskimi in drugimi anorganskimi prevlekami.
Preskus trdote po Vickersu je v tem dokumentu določen za dolžine diagonal zarez od 0,020 do 1,400 mm. Uporaba te metode za določanje trdote po Vickersu na podlagi manjših zarez ne sodi na področje uporabe tega dokumenta, saj bi bili rezultati nezanesljivi zaradi negotovosti, povezane z omejitvami optičnega merjenja in nepravilnostmi geometrije konice.
Trdota po Vickersu, določena v tem dokumentu, velja tudi za kovinske in druge anorganske prevleke, vključno z elektrogalvanskimi prevlekami, samokatalitičnimi prevlekami, razpršenimi prevlekami in anodnimi prevlekami na aluminiju.
Ta dokument se uporablja za meritve pravokotno na prevlečeno površino in meritve na prečnih prerezih pod pogojem, da lastnosti prevleke (gladkost, debelina itd.) dovoljujejo točno odčitavanje diagonale zareze.
Ta dokument se ne uporablja za prevleke z debelino manj kot 0,030 mm pri meritvah pravokotno na površino prevleke. Ta standard se ne uporablja za prevleke z debelino manj kot 0,100 mm pri meritvah prečnega prereza prevleke. Standard ISO 14577-1 se lahko uporablja za določanje trdote
manjših zarez.
Določena je tudi metoda za redno preverjanje pri rutinskem pregledovanju naprave za preskušanje, ki jo uporablja
uporabnik. Za posebne materiale in/ali izdelke obstajajo posamezni mednarodni standardi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 6507-1:2023
01-december-2023
Kovinski materiali - Preskus trdote po Vickersu - 1. del: Preskusna metoda (ISO
6507-1:2023)
Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1:2023)
Metallische Werkstoffe – Härteprüfung nach Vickers – Teil1: Prüfverfahren (ISO 6507-
1:2023)
Matériaux métalliques - Essai de dureté Vickers - Partie 1: Méthode d'essai (ISO 6507-
1:2023)
Ta slovenski standard je istoveten z: EN ISO 6507-1:2023
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 6507-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 6507-1:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 6507-1:2023
EN ISO 6507-1
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2023
EUROPÄISCHE NORM
ICS 77.040.10 Supersedes EN ISO 6507-1:2018
English Version
Metallic materials - Vickers hardness test - Part 1: Test
method (ISO 6507-1:2023)
Matériaux métalliques - Essai de dureté Vickers - Partie Metallische Werkstoffe - Härteprüfung nach Vickers -
1: Méthode d'essai (ISO 6507-1:2023) Teil 1: Prüfverfahren (ISO 6507-1:2023)
This European Standard was approved by CEN on 25 August 2023.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6507-1:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 6507-1:2023
EN ISO 6507-1:2023 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 6507-1:2023
EN ISO 6507-1:2023 (E)
European foreword
This document (EN ISO 6507-1:2023) has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals" in collaboration with Technical Committee CEN/TC 459/SC 1 “Test
methods for steel (other than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2024, and conflicting national standards shall be
withdrawn at the latest by April 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6507-1:2018.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 6507-1:2023 has been approved by CEN as EN ISO 6507-1:2023 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 6507-1:2023
---------------------- Page: 6 ----------------------
SIST EN ISO 6507-1:2023
INTERNATIONAL ISO
STAND
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.