Rubber hoses, textile-reinforced, for compressed air - Specification (ISO 2398:2024)

ISO 2398:2016 specifies the requirements for three types, three classes and two categories of textile-reinforced rubber hose for compressed air, up to a maximum working pressure of 25 bar with an operating-temperature range of −40 °C to +70 °C, depending on the type and category.

Gummischläuche mit Textileinlage für Druckluft - Anforderung (ISO 2398:2024)

Dieses Dokument legt die Anforderungen an drei Typen, drei Klassen und zwei Kategorien von Gummischläuchen mit Textileinlage für Druckluft fest, mit einem maximalen Betriebsdruck von 2,5 MPa (25 bar) und einem Betriebstemperaturbereich von −40 °C bis +70 °C in Abhängigkeit von Typ und Kategorie.
WARNUNG — Die Anwender dieses Dokuments sollten mit der üblichen Laborpraxis vertraut sein. Dieses Dokument beansprucht nicht, sämtliche mit ihrer Anwendung verbundenen Sicherheitsprobleme, soweit diese gegeben sind, zu behandeln. Es liegt in der Verantwortung des Anwenders, die angemessenen Maßnahmen in Bezug auf den Gesundheits- und Arbeitsschutz einzuleiten.

Tuyaux en caoutchouc renforcés textile pour l'air comprimé - Spécifications (ISO 2398:2024)

ISO 2398:2016 spécifie les exigences pour trois types, trois classes et deux catégories de tuyaux en caoutchouc renforcés textile pour l'air comprimé, pouvant être utilisés jusqu'à une pression maximale de service de 25 bar et sur une plage de températures de service de −40 °C à +70 °C, en fonction du type et de la catégorie.

S tekstilom ojačene gumene cevi za stisnjeni zrak - Specifikacija (ISO 2398:2024)

Standard ISO 2398:2016 določa zahteve za tri vrste, tri razrede in dve kategoriji s tekstilom ojačenih gumenih cevi za stisnjeni zrak z največjim delovnim tlakom 25 barov pri delovnih temperaturah od –40 °C do +70 °C, odvisno od vrste in kategorije.

General Information

Status
Published
Public Enquiry End Date
09-May-2023
Publication Date
19-May-2024
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
16-May-2024
Due Date
21-Jul-2024
Completion Date
20-May-2024

Relations

Buy Standard

Standard
EN ISO 2398:2024
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2024
Nadomešča:
SIST EN ISO 2398:2017
S tekstilom ojačene gumene cevi za stisnjeni zrak - Specifikacija (ISO 2398:2024)
Rubber hoses, textile-reinforced, for compressed air - Specification (ISO 2398:2024)
Gummischläuche mit Textileinlage für Druckluft - Anforderung (ISO 2398:2024)
Tuyaux en caoutchouc renforcés textile pour l'air comprimé - Spécifications (ISO
2398:2024)
Ta slovenski standard je istoveten z: EN ISO 2398:2024
ICS:
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 2398
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 2398:2016
English Version
Rubber hoses, textile-reinforced, for compressed air -
Specification (ISO 2398:2024)
Tuyaux en caoutchouc renforcés textile pour l'air Gummischläuche mit Textileinlage für Druckluft -
comprimé - Spécifications (ISO 2398:2024) Anforderung (ISO 2398:2024)
This European Standard was approved by CEN on 12 June 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2398:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 2398:2024) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2024, and conflicting national standards
shall be withdrawn at the latest by November 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2398:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 2398:2024 has been approved by CEN as EN ISO 2398:2024 without any modification.

International
Standard
ISO 2398
Seventh edition
Rubber hoses, textile-reinforced, for
2024-04
compressed air — Specification
Tuyaux en caoutchouc renforcés textile pour l'air comprimé —
Spécifications
Reference number
ISO 2398:2024(en) © ISO 2024
ISO 2398:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 2398:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Materials and construction . 2
6 Dimensions . 2
6.1 Inside diameters and tolerances .2
6.2 Concentricity .3
6.3 Tolerance on length .3
6.4 Minimum thickness of lining and cover .3
7 Physical properties . 3
7.1 Rubber compounds .3
7.2 Finished hose .4
8 Frequency of testing . . 4
9 Test report or certificate . 5
10 Marking . . 5
Annex A (normative) Type tests and routine tests . 6

iii
ISO 2398:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee
SC 1, Rubber and plastics hoses and hose assemblies, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 218, Rubber and plastics hoses and hose assemblies, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This seventh edition cancels and replaces the sixth edition (ISO 2398:2016), which has been technically
revised.
The main changes are as follows:
— Table A.1, test requirements have been revised;
— Annex B has been deleted.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
International Standard ISO 2398:2024(en)
Rubber hoses, textile-reinforced, for compressed air —
Specification
WARNING — Persons using this document should be familiar with normal laboratory practice. This
document does not purport to address all of the safety problems, if any, associated with its use. It is
the responsibility of the user to establish appropriate health and safety practices.
1 Scope
This document specifies the requirements for three types, three classes and two categories of textile-
reinforced rubber hose for compressed air, up to a maximum working pressure of 2,5 MPa (25 bar) with an
operating-temperature range of −40 °C to +70 °C, depending on the type and category.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on
cut-to-length hoses
ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses
and the lengths of hose assemblies
ISO 7326:2016, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
ISO 8033, Rubber and plastics
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.