SIST EN 301 502 V12.5.2:2017
(Main)Global System for Mobile communications (GSM) - Base Station (BS) equipment - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
Global System for Mobile communications (GSM) - Base Station (BS) equipment - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
The present document contains requirements aiming to demonstrate that that radio equipment both effectively uses and
supports the efficient use of radio spectrum in order to avoid harmful interference.
In regards to interference to systems operating in adjacent bands guidance for single carrier BTS and multicarrier BTS
is provided in ECC Report 146 [i.3].
Globalni sistem mobilnih komunikacij (GSM) - Oprema bazne postaje - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da je radijska oprema izdelana tako, da učinkovito uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivega motenja.
Kar zadeva motnje sistemov, ki delujejo v sosednjih pasovih, so v Poročilo 146 Odbora za elektronske komunikacije [i.3] vključena navodila za enega ali več operaterjev baznih sprejemno-oddajnih postaj (BTS).
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Global System for Mobile communications (GSM) - Base Station (BS) equipment - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU33.070.50Globalni sistem za mobilno telekomunikacijo (GSM)Global System for Mobile Communication (GSM)ICS:Ta slovenski standard je istoveten z:ETSI EN 301 502 V12.5.2 (2017-03)SIST EN 301 502 V12.5.2:2017en01-maj-2017SIST EN 301 502 V12.5.2:2017SLOVENSKI
STANDARD
SIST EN 301 502 V12.5.2:2017
ETSI EN 301 502 V12.5.2 (2017-03) Global System for Mobile communications (GSM); Base Station (BS) equipment; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 301 502 V12.5.2:2017
ETSI ETSI EN 301 502 V12.5.2 (2017-03) 2
Reference REN/MSG-0019-RED-C1 Keywords base station, cellular, ER-GSM, GSM, R-GSM ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 502 V12.5.2:2017
ETSI ETSI EN 301 502 V12.5.2 (2017-03) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 10 3 Definitions, symbols and abbreviations . 11 3.1 Definitions . 11 3.2 Symbols . 13 3.3 Abbreviations . 13 4 Technical requirements specifications . 15 4.1 Environmental profile . 15 4.2 Conformance requirements . 15 4.2.0 General . 15 4.2.1 Introduction. 15 4.2.2 Mean transmitted RF carrier power . 16 4.2.2.1 Definition . 16 4.2.2.2 Limit . 16 4.2.2.3 Conformance . 17 4.2.3 Void . 17 4.2.4 Adjacent channel power . 17 4.2.4.0 General . 17 4.2.4.1 Spectrum due to modulation and wideband noise . 17 4.2.4.1.1 Definition. 17 4.2.4.1.2 Limit . 17 4.2.4.1.3 Conformance . 19 4.2.4.2 Switching transients spectrum . 20 4.2.4.2.1 Definition. 20 4.2.4.2.2 Limit . 20 4.2.4.2.3 Conformance . 20 4.2.5 Spurious emissions from the transmitter antenna connector . 20 4.2.5.0 General . 20 4.2.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit band . 20 4.2.5.1.1 Definition. 20 4.2.5.1.2 Limit . 20 4.2.5.1.3 Conformance . 20 4.2.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit band . 21 4.2.5.2.0 General . 21 4.2.5.2.1 Definition. 21 4.2.5.2.2 Limit . 21 4.2.5.2.3 Conformance . 22 4.2.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the BTS transmit band . 22 4.2.5.3.0 General . 22 4.2.5.3.1 Definition. 22 4.2.5.3.2 Limit . 22 4.2.5.3.3 Conformance . 22 4.2.6 Intermodulation attenuation . 22 4.2.6.1 Definition . 22 4.2.6.2 Limit . 23 SIST EN 301 502 V12.5.2:2017
ETSI ETSI EN 301 502 V12.5.2 (2017-03) 4 4.2.6.2.1 For BTS not belonging to a multicarrier BTS class . 23 4.2.6.2.2 For BTS belonging to a multicarrier BTS class . 23 4.2.6.3 Conformance . 23 4.2.7 Intra Base Station System intermodulation attenuation . 24 4.2.7.1 Definition . 24 4.2.7.2 Limit . 24 4.2.7.2.1 For BTS not belonging to a multicarrier BTS class . 24 4.2.7.2.2 For BTS belonging to a multicarrier BTS class . 24 4.2.7.3 Conformance . 24 4.2.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 24 4.2.8.1 Definition . 24 4.2.8.2 Limit . 24 4.2.9 Static Reference Sensitivity Level . 26 4.2.9.1 Definition . 26 4.2.9.2 Limit . 26 4.2.9.3 Conformance . 27 4.2.10 Void . 27 4.2.11 Reference Interference Level . 27 4.2.11.1 Definition . 27 4.2.11.2 Limit . 28 4.2.11.3 Conformance . 34 4.2.12 Blocking Characteristics . 34 4.2.12.0 General . 34 4.2.12.1 Definition . 35 4.2.12.2 Limit . 35 4.2.12.2.1 Blocking . 35 4.2.12.2.2 Spurious response . 36 4.2.12.3 Conformance . 36 4.2.13 Intermodulation characteristics . 36 4.2.13.1 Definition . 36 4.2.13.2 Limit . 36 4.2.13.3 Conformance . 36 4.2.14 AM suppression . 36 4.2.14.1 Definition . 36 4.2.14.2 Limit . 36 4.2.14.3 Conformance . 37 4.2.15 Spurious emissions from the receiver antenna connector . 37 4.2.15.0 General . 37 4.2.15.1 Definition . 37 4.2.15.2 Limit . 37 4.2.15.3 Conformance . 37 4.2.16 Radiated spurious emissions . 37 4.2.16.0 General . 37 4.2.16.1 Definition . 37 4.2.16.2 Limit . 37 4.2.16.3 Conformance . 37 5 Testing for compliance with technical requirements . 38 5.1 Environmental conditions for testing . 38 5.2 Interpretation of the measurement results . 38 5.3 Essential radio test suites . 39 5.3.0 General . 39 5.3.1 Void . 39 5.3.2 Mean transmitted RF carrier power . 39 5.3.2.1 Test case . 39 5.3.2.2 Test Environment . 40 5.3.3 Void . 41 5.3.4 Adjacent channel power . 41 5.3.4.1 Spectrum due to modulation and wideband noise . 41 5.3.4.1.1 Test case . 41 5.3.4.1.2 Test Environment . 41 5.3.4.2 Switching transients spectrum . 42 SIST EN 301 502 V12.5.2:2017
ETSI ETSI EN 301 502 V12.5.2 (2017-03) 5 5.3.4.2.1 Test case . 42 5.3.4.2.2 Test Environment . 43 5.3.5 Spurious emissions from the transmitter antenna connector . 43 5.3.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit band . 43 5.3.5.1.1 Test case . 43 5.3.5.1.2 Test Environment . 43 5.3.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit band . 44 5.3.5.2.0 General . 44 5.3.5.2.1 For BTS not belonging to a multicarrier BTS class . 44 5.3.5.2.2 For BTS belonging to a multicarrier BTS class . 45 5.3.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the BTS transmit band . 47 5.3.5.3.0 General . 47 5.3.5.3.1 Test case . 47 5.3.5.3.2 Test Environment . 47 5.3.6 Intermodulation attenuation . 47 5.3.6.1 Test case . 47 5.3.6.2 Test Environment . 49 5.3.7 Intra Base Station System intermodulation attenuation . 49 5.3.7.1 Test case . 49 5.3.7.2 Test Environment . 50 5.3.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 50 5.3.8.1 Test case . 50 5.3.8.2 Test Environment . 53 5.3.9 Static reference sensitivity level . 53 5.3.9.1 Test case . 53 5.3.9.2 Test Environment . 54 5.3.10 Void . 54 5.3.11 Reference Interference Level . 54 5.3.11.1 Test case . 54 5.3.11.2 Test Environment . 63 5.3.12 Blocking Characteristics . 63 5.3.12.0 General . 63 5.3.12.1 Test case . 63 5.3.12.2 Test Environment . 69 5.3.13 Intermodulation characteristics . 69 5.3.13.1 Test case . 69 5.3.13.2 Test Environment . 70 5.3.14 AM suppression . 70 5.3.14.1 Test case . 70 5.3.14.2 Test Environment . 72 5.3.15 Spurious emissions from the receiver antenna connector . 72 5.3.15.0 General . 72 5.3.15.1 Test case . 72 5.3.15.2 Test Environment . 72 5.3.16 Radiated spurious emissions . 73 5.3.16.0 General . 73 5.3.16.1 Test case . 74 5.3.16.2 Test Environment . 75 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 76 Annex B (normative): General test conditions and declarations . 78 B.1 Declaration by manufacturer . 78 B.1.0 General . 78 B.1.1 Outpu
...
ETSI EN 301 502 V12.5.2 (2017-03)
HARMONISED EUROPEAN STANDARD
Global System for Mobile communications (GSM);
Base Station (BS) equipment;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 301 502 V12.5.2 (2017-03)
Reference
REN/MSG-0019-RED-C1
Keywords
base station, cellular, ER-GSM, GSM, R-GSM
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 502 V12.5.2 (2017-03)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 7
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical requirements specifications . 15
4.1 Environmental profile . 15
4.2 Conformance requirements . 15
4.2.0 General . 15
4.2.1 Introduction. 15
4.2.2 Mean transmitted RF carrier power . 16
4.2.2.1 Definition . 16
4.2.2.2 Limit . 16
4.2.2.3 Conformance . 17
4.2.3 Void . 17
4.2.4 Adjacent channel power . 17
4.2.4.0 General . 17
4.2.4.1 Spectrum due to modulation and wideband noise . 17
4.2.4.1.1 Definition. 17
4.2.4.1.2 Limit . 17
4.2.4.1.3 Conformance . 19
4.2.4.2 Switching transients spectrum . 20
4.2.4.2.1 Definition. 20
4.2.4.2.2 Limit . 20
4.2.4.2.3 Conformance . 20
4.2.5 Spurious emissions from the transmitter antenna connector . 20
4.2.5.0 General . 20
4.2.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 20
4.2.5.1.1 Definition. 20
4.2.5.1.2 Limit . 20
4.2.5.1.3 Conformance . 20
4.2.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 21
4.2.5.2.0 General . 21
4.2.5.2.1 Definition. 21
4.2.5.2.2 Limit . 21
4.2.5.2.3 Conformance . 22
4.2.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 22
4.2.5.3.0 General . 22
4.2.5.3.1 Definition. 22
4.2.5.3.2 Limit . 22
4.2.5.3.3 Conformance . 22
4.2.6 Intermodulation attenuation . 22
4.2.6.1 Definition . 22
4.2.6.2 Limit . 23
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 502 V12.5.2 (2017-03)
4.2.6.2.1 For BTS not belonging to a multicarrier BTS class . 23
4.2.6.2.2 For BTS belonging to a multicarrier BTS class . 23
4.2.6.3 Conformance . 23
4.2.7 Intra Base Station System intermodulation attenuation . 24
4.2.7.1 Definition . 24
4.2.7.2 Limit . 24
4.2.7.2.1 For BTS not belonging to a multicarrier BTS class . 24
4.2.7.2.2 For BTS belonging to a multicarrier BTS class . 24
4.2.7.3 Conformance . 24
4.2.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 24
4.2.8.1 Definition . 24
4.2.8.2 Limit . 24
4.2.9 Static Reference Sensitivity Level . 26
4.2.9.1 Definition . 26
4.2.9.2 Limit . 26
4.2.9.3 Conformance . 27
4.2.10 Void . 27
4.2.11 Reference Interference Level . 27
4.2.11.1 Definition . 27
4.2.11.2 Limit . 28
4.2.11.3 Conformance . 34
4.2.12 Blocking Characteristics . 34
4.2.12.0 General . 34
4.2.12.1 Definition . 35
4.2.12.2 Limit . 35
4.2.12.2.1 Blocking . 35
4.2.12.2.2 Spurious response . 36
4.2.12.3 Conformance . 36
4.2.13 Intermodulation characteristics . 36
4.2.13.1 Definition . 36
4.2.13.2 Limit . 36
4.2.13.3 Conformance . 36
4.2.14 AM suppression . 36
4.2.14.1 Definition . 36
4.2.14.2 Limit . 36
4.2.14.3 Conformance . 37
4.2.15 Spurious emissions from the receiver antenna connector . 37
4.2.15.0 General . 37
4.2.15.1 Definition . 37
4.2.15.2 Limit . 37
4.2.15.3 Conformance . 37
4.2.16 Radiated spurious emissions . 37
4.2.16.0 General . 37
4.2.16.1 Definition . 37
4.2.16.2 Limit . 37
4.2.16.3 Conformance . 37
5 Testing for compliance with technical requirements . 38
5.1 Environmental conditions for testing . 38
5.2 Interpretation of the measurement results . 38
5.3 Essential radio test suites . 39
5.3.0 General . 39
5.3.1 Void . 39
5.3.2 Mean transmitted RF carrier power . 39
5.3.2.1 Test case . 39
5.3.2.2 Test Environment . 40
5.3.3 Void . 41
5.3.4 Adjacent channel power . 41
5.3.4.1 Spectrum due to modulation and wideband noise . 41
5.3.4.1.1 Test case . 41
5.3.4.1.2 Test Environment . 41
5.3.4.2 Switching transients spectrum . 42
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 502 V12.5.2 (2017-03)
5.3.4.2.1 Test case . 42
5.3.4.2.2 Test Environment . 43
5.3.5 Spurious emissions from the transmitter antenna connector . 43
5.3.5.1 Conducted spurious emissions from the transmitter antenna connector, inside the BTS transmit
band . 43
5.3.5.1.1 Test case . 43
5.3.5.1.2 Test Environment . 43
5.3.5.2 Conducted spurious emissions from the transmitter antenna connector, outside the BTS transmit
band . 44
5.3.5.2.0 General . 44
5.3.5.2.1 For BTS not belonging to a multicarrier BTS class . 44
5.3.5.2.2 For BTS belonging to a multicarrier BTS class . 45
5.3.5.3 Conducted spurious emissions from the transmitter antenna connector, in 3G bands outside the
BTS transmit band . 47
5.3.5.3.0 General . 47
5.3.5.3.1 Test case . 47
5.3.5.3.2 Test Environment . 47
5.3.6 Intermodulation attenuation . 47
5.3.6.1 Test case . 47
5.3.6.2 Test Environment . 49
5.3.7 Intra Base Station System intermodulation attenuation . 49
5.3.7.1 Test case . 49
5.3.7.2 Test Environment . 50
5.3.8 Wideband noise and intra BSS intermodulation attenuation in multicarrier operation . 50
5.3.8.1 Test case . 50
5.3.8.2 Test Environment . 53
5.3.9 Static reference sensitivity level . 53
5.3.9.1 Test case . 53
5.3.9.2 Test Environment . 54
5.3.10 Void . 54
5.3.11 Reference Interference Level . 54
5.3.11.1 Test case . 54
5.3.11.2 Test Environment . 63
5.3.12 Blocking Characteristics . 63
5.3.12.0 General . 63
5.3.12.1 Test case . 63
5.3.12.2 Test Environment . 69
5.3.13 Intermodulation characteristics . 69
5.3.13.1 Test case . 69
5.3.13.2 Test Environment . 70
5.3.14 AM suppression . 70
5.3.14.1 Test case . 70
5.3.14.2 Test Environment . 72
5.3.15 Spurious emissions from the receiver antenna connector . 72
5.3.15.0 General . 72
5.3.15.1 Test case . 72
5.3.15.2 Test Environment . 72
5.3.16 Radiated spurious emissions . 73
5.3.16.0 General . 73
5.3.16.1 Test case . 74
5.3.16.2 Test Environment . 75
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 76
Annex B (normative): General test conditions and declarations . 78
B.1 Declaration by manufacturer . 78
B.1.0 General . 78
B.1.1 Output power and determination of power class . 78
B.1.2 Specified frequency range .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.