SIST ETS 300 607-3 E10:2003
(Main)Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 3: Layer 3 (L3) Abstract Test Suite (ATS) (GSM 11.10-3 version 4.24.1)
Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS) conformance specification; Part 3: Layer 3 (L3) Abstract Test Suite (ATS) (GSM 11.10-3 version 4.24.1)
SUBJECT Implementing TDoc 7-67/98 Implementation Error: Incorrect Use Of Cell Allocation Data Strucutures Implementation error in Handover test cases sends wrong SysInfo6 message Implementation errors in the 26.6.5.4 test case series Implementation of Tdoc SMG7 137/98 (Hopping Channel required) Implementation problems in 26.6.13 series DCS Test Cases Problem in MO test cases for Dual Rate phones Problem with conflicting carrier initialisation in TC_20_15 Problem implementing a TTCN pre-defined operation DCS implementation error in the 26.6.5.1 test case DCS Handover Tests, NCD to include BCCH arfcn Correction for DCS frequencies for 26_6_4_1 Implementation errors in Handover test cases for Releasing the Channel being Handed Over From SI3 coding conflict in 26.2.4.3 and 26.2.4.4 Implementation errors in Handover test cases cause L2 reaching N200 limit RF Signal parameter change for TC_20_1
Digitalni celični telekomunikacijski sistem (faza 2) – Specifikacija skladnosti za mobilne postaje (MS) – 3. del: Abstraktni preskušalni niz (ATS) tretje plasti (L3) (GSM 11.10-3 različica 4.24.1)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2003
'LJLWDOQLFHOLþQLWHOHNRPXQLNDFLMVNLVLVWHP ID]D ±6SHFLILNDFLMDVNODGQRVWL]D
PRELOQHSRVWDMH 06 ±GHO $EVWUDNWQLSUHVNXãDOQLQL] $76 WUHWMHSODVWL /
*60UD]OLþLFD
Digital cellular telecommunications system (Phase 2) (GSM); Mobile Station (MS)
conformance specification; Part 3: Layer 3 (L3) Abstract Test Suite (ATS) (GSM 11.10-3
version 4.24.1)
Ta slovenski standard je istoveten z: ETS 300 607-3 Edition 10
ICS:
33.070.50 Globalni sistem za mobilno Global System for Mobile
telekomunikacijo (GSM) Communication (GSM)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN ETS 300 607-3
TELECOMMUNICATION April 1999
STANDARD Tenth Edition
Source: SMG Reference: RE/SMG-071110PR8-3
ICS: 33.020
Key words: Digital cellular telecommunications system, Global System for Mobile Communication (GSM)
R
GLOBAL SYSTEM FOR
MOBILE COMMUNICATIONS
Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 3: Layer 3 (L3) Abstract Test Suite (ATS)
(GSM 11.10-3 version 4.24.1)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
Internet: secretariat@etsi.fr - http://www.etsi.org
Tel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16
Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1999. All rights reserved.
Page 2
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Standards Making Support Dept." at the address shown on the title page.
Page 3
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Contents
Foreword .5
1 Scope .7
2 Normative references.7
3 Definitions and abbreviations .10
3.1 Definitions .10
3.2 Abbreviations .10
4 Test Suite Structure (TSS) .11
4.1 Test suite naming convention .11
4.2 Suite Overview.12
4.3 Test groups.12
4.3.1 Valid Behaviour tests (BV) .12
4.3.2 Invalid Behaviour/Inopportune Behaviour tests (BI-BO).12
4.4 Test Step Structure.13
4.4.1 Preambles .13
4.4.2 Postambles.13
5 Test Purposes (TP).13
5.1 TP and test case naming convention.13
6 Abstract test method and test configurations.13
6.1 Test system model.13
6.2 Test Method.14
Annex A (normative): Layer 3 Abstract Test Suite .15
A.1 The TTCN Graphical form (TTCN.GR) .15
A.2 The TTCN Machine Processable form (TTCN.MP) .15
Annex B (normative): Partial IXIT proforma .16
Introduction.16
B.1 Identification Summary.17
B.2 Abstract Test Suite Summary .17
B.3 Test Laboratory .17
B.3.1 Test Laboratory Identification.17
B.3.2 Accreditation status of the test service .18
B.3.3 Manager of Test Laboratory.18
B.3.4 Contact person of Test Laboratory .18
B.3.5 Means of Testing .19
B.3.6 Instructions for Completion.20
B.4 Client .21
B.4.1 Client Identification.21
B.4.2 Client Test Manager.21
B.4.3 Client Contact person .21
B.4.4 Test Facilities Required .22
B.5 System Under Test.23
Page 4
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.5.1 SUT Information. 23
B.5.2 Limitations of the SUT. 24
B.5.3 Environmental Conditions . 25
B.6 Ancillary Protocols . 26
B.6.1 Ancillary Protocols 1. 26
B.6.2 Ancillary Protocols 2. 26
B.7 Protocol Layer Information for L3 of Mobile Station.26
B.7.1 Information provided for test purposes by the MS supplier. 26
B.7.2 MMI information . 39
B.7.3 Test house specified parameters. 44
Annex C (normative): PCTR Proforma . 76
Annex D (normative): Enhanced Full Rate Abstract Test Suite. 77
D.1 The TTCN Graphical form (TTCN.GR) .77
D.2 The TTCN Machine Processable form (TTCN.MP) . 77
Annex E (informative): Cell Selection Abstract Test Suite. 78
E.1 The TTCN Graphical form (TTCN.GR) .78
E.2 The TTCN Machine Processable form (TTCN.MP) . 78
Annex F (informative): Dual band Abstract Test Suite . 79
F.1 The TTCN Graphical form (TTCN.GR) .79
F.2 The TTCN Machine Processable form (TTCN.MP) . 79
History. 80
Page 5
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Foreword
This European Telecommunication Standard (ETS) has been produced by the Special Mobile Group
(SMG) of the European Telecommunications Standards Institute (ETSI).
This ETS describes the technical characteristics and methods of test for Mobile Stations (MSs), operating
in the 900 MHz and 1 800 MHz frequency band (GSM 900 and DCS 1 800) within the digital cellular
telecommunications system.
This ETS corresponds to GSM technical specification GSM 11.10-3 version 4.24.0.
This part of the ETS (Part 3), contains Tree and Tabular Combined Notation (TTCN) for Layer 3,
signalling for MS supporting Enhanced Full Rate Speech, and cell selection conformity specifications for
which Mobile Stations, within the digital cellular telecommunications system (Phase 2), are tested for
compliance.
The graphical form ATS
The electronic forms of the graphical representation (TTCN.GR format) corresponding to the ATS for
Layer 3 are contained in the Adobe Portable Document Format™ files L3-4n0.PDF (Layer 3), EF-4n0.PDF
(Enhanced Full Rate), CS-4n0.PDF (Cell Selection) and DB-4n0.PDF (Dual Band) which accompany this
ETS (Part 3) (these files are contained in archive 6073_ea.ZIP).
The machine processable ATS
The electronic forms of the machine processable files (TTCN.MP format) corresponding to the ATS for
Layer 3 are contained in the ASCII files L3-4o0.mp (Layer 3), EF-4o0.mp (Enhanced Full Rate),
CS-4o0.mp (Cell Selection) and DB-4o0.mp (Dual Band) which accompany this ETS (Part 3) (these files
are contained in archive 6073_ea.ZIP).
ETS 300 607 consists of three parts, which have the following ETS numbers and titles:
ETS 300 607-1 Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 1: Conformance specification
Reference: GSM 11.10-1.
ETS 300 607-2 Digital cellular telecommunications system (Phase 2);
Mobile Station (MS) conformance specification;
Part 2: Protocol Implementation Conformance Statement (ICS)
proforma specification
Reference: GSM 11.10-2.
ETS 300 607-3 Digital cellular telecommunications system (Phase 1);
Mobile Station (MS) conformance specification;
Part 3: Layer 3 (L3) Abstract Test Suite (ATS)
Reference: GSM 11.10-3.
Transposition dates
Date of adoption of this ETS: 9 April 1999
Date of latest announcement of this ETS (doa): 31 July 1999
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 January 2000
Date of withdrawal of any conflicting National Standard (dow): 31 January 2000
Page 6
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Blank page
Page 7
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
1 Scope
This European Telecommunication Standard (ETS) specifies the Abstract Test Suite (ATS) and partial
IXIT proforma for the Network Layer (Layer 3) at the mobile radio interface of the GSM or DCS (Phase 2)
mobile stations (MS) conforming to the ETSs for the Radio Resource management, the Mobility
Management, the circuit-switched Call Control, the Supplementary Services and Short Message Services
for the digital cellular telecommunications systems (Phase 2).
The ISO standards for the methodology of conformance testing are used as the basis for the test
specifications.
2 Normative references
This ETS incorporates by dated and undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text and the publications are listed
hereafter. For dated references, subsequent amendments to or revisions of any of these publications
apply to this ETS only when incorporated in it by amendment or revision. For undated references, the
latest edition of the publication referred to applies.
[1] ISO/IEC 9646-1: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 1: General Concepts".
[2] ISO/IEC 9646-2: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 2: Abstract Test Suite Specification".
[3] ISO/IEC 9646-3: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 3: The Tree and Tabular Combined
Notation".
[4] ISO/IEC 9646-5: "Information Technology-OSI- Conformance Testing
Methodology and Framework, Part 5: Requirements on test laboratories and
clients for the conformance assessment process".
[5] ISO/IEC 8824: "Information Technology-OSI- Specification of Abstract Syntax
Notation One (ASN.1)".
[6] ISO/IEC 8825: "Information Technology-OSI- Specification of Basic Encoding
Rules for Abstract Syntax Notation One (ASN.1)".
[7] ITU-T Recommendation Q.773: "Specifications of Signalling System No.7;
Transaction capabilities formats and encoding".
[8] ETS 300 287: "Integrated Services Digital Network (ISDN); Signalling System
No.7, Transaction Capabilities Application Part (TCAP) version 2".
[9] ETS 300 406 (January 1995): "Methods for Testing and Specification (MTS);
Protocol and profile conformance testing specifications; Standardization
methodology".
[10] GSM 02.02 Version 4.2.2: "Digital cellular telecommunication system (Phase 2);
Bearer Services (BS) supported by a GSM Public Land Mobile Network
(PLMN)".
[11] GSM 02.03 Version 4.3.1: "Digital cellular telecommunication system (Phase 2);
Teleservices supported by a GSM Public Land Mobile Network (PLMN)".
[12] GSM 02.06 Version 4.5.2: "Digital cellular telecommunication system (Phase 2);
Types of Mobile Stations (MS)".
[13] GSM 02.07 Version 4.8.2: "Digital cellular telecommunication system (Phase 2);
Mobile Station (MS) features".
Page 8
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
[14] GSM 02.30 Version 4.13.0: "Digital cellular telecommunication system
(Phase 2); Man-Machine Interface (MMI) of the Mobile Station (MS)".
[15] GSM 03.03 Version 4.9.0: "Digital cellular telecommunication system (Phase 2);
Numbering, addressing and identification".
[16] GSM 03.09 Version 4.6.0: "Digital cellular telecommunications system
(Phase 2); Handover procedures".
[17] GSM 03.10 Version 4.3.1: "Digital cellular telecommunications system
(Phase 2); GSM Public Land Mobile Network (PLMN) connection types".
[18] GSM 03.11 Version 4.10.1: "Digital cellular telecommunication system
(Phase 2); Technical realization of supplementary services".
[19] GSM 03.12 Version 4.4.2: "Digital cellular telecommunications system
(Phase 2); Location registration procedures".
[20] GSM 03.14 Version 4.1.1: "Digital cellular telecommunications system
(Phase 2); Support of Dual Tone Multi-Frequency signalling (DTMF) via the
GSM system".
[21] GSM 03.22 Version 4.11.0: "Digital cellular telecommunication system
(Phase 2); Functions related to Mobile Station (MS) in idle mode".
[22] GSM 03.40 Version 4.13.0: "Digital cellular telecommunication system
(Phase 2); Technical realization of the Short Message Service (SMS) Point to
Point (PP)".
[23] GSM 03.41 Version 4.11.0: "Digital cellular telecommunication system
(Phase 2); Technical realization of Short Message Service Cell Broadcast
(SMSCB)".
[24] GSM 04.01 Version 4.0.4: "Digital cellular telecommunications system
(Phase 2); Mobile Station - Base Station System (MS - BSS) interface General
aspects and principles".
[25] GSM 04.03 Version 4.1.1: "Digital cellular telecommunications system
(Phase 2); Mobile Station - Base Station System (MS - BSS) interface Channel
structures and access capabilities".
[26] GSM 04.04 Version 4.0.4: "Digital cellular telecommunication system (Phase 2);
layer 1 General requirements".
[27] GSM 04.05 Version 4.0.3: "Digital cellular telecommunication system (Phase 2);
Data Link (DL) layer General aspects".
[28] GSM 04.06 Version 4.4.0: "Digital cellular telecommunication system (Phase 2);
Mobile Station - Base Station System (MS - BSS) interface Data Link (DL) layer
specification".
[29] GSM 04.07 Version 4.3.1: "Digital cellular telecommunication system (Phase 2);
Mobile radio interface signalling layer 3 General aspects".
[30] GSM 04.08 Version 4.22.1: "Digital cellular telecommunication system
(Phase 2); Mobile radio interface layer 3 specification".
[31] GSM 04.10 Version 4.10.1: "Digital cellular telecommunication system
(Phase 2); Mobile radio interface layer 3 Supplementary services specification
General aspects".
Page 9
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
[32] GSM 04.11 Version 4.10.0: "Digital cellular telecommunication system
(Phase 2); Point-to-Point (PP) Short Message Service (SMS) support on mobile
radio interface".
[33] GSM 04.12 Version 4.6.0: "Digital cellular telecommunication system (Phase 2);
Short Message Service Cell Broadcast (SMSCB) support on the mobile radio
interface".
[34] GSM 04.80 Version 4.11.1: "Digital cellular telecommunication system
(Phase 2); Mobile radio interface layer 3 supplementary services specification;
Formats and coding".
[35] GSM 04.81 Version 4.4.1: "Digital cellular telecommunication system (Phase 2);
Line identification supplementary services - Stage 3".
[36] GSM 04.82 Version 4.9.1: "Digital cellular telecommunication system (Phase 2);
Call Forwarding (CF) supplementary services - Stage 3".
[37] GSM 04.83 Version 4.6.1: "Digital cellular telecommunication system (Phase 2);
Call Waiting (CW) and Call Hold (HOLD) supplementary services - Stage 3".
[38] GSM 04.84 Version 4.3.2: "Digital cellular telecommunication system (Phase 2);
MultiParty (MPTY) supplementary services - Stage 3".
[39] GSM 04.85 Version 4.1.1: "Digital cellular telecommunications system
(Phase 2); Closed User Group (CUG) supplementary services - Stage 3".
[40] GSM 04.86 Version 4.5.2: "Digital cellular telecommunication system (Phase 2);
Advice of Charge (AoC) supplementary services - Stage 3".
[41] GSM 04.88 Version 4.7.1: "Digital cellular telecommunication system (Phase 2);
Call Barring (CB) supplementary services - Stage 3".
[42] GSM 04.90 Version 4.1.1: "Digital cellular telecommunication system (Phase 2);
Unstructured supplementary services operation - Stage 3".
[43] GSM 05.01 Version 4.6.0: "Digital cellular telecommunications system
(Phase 2); Physical layer on the radio path General description".
[44] GSM 05.02 Version 4.9.1: "Digital cellular telecommunication system (Phase 2);
Multiplexing and multiple access on the radio path".
[45] GSM 05.03 Version 4.5.1: "Digital cellular telecommunication system (Phase 2);
Channel coding".
[46] GSM 05.04 Version 4.0.3: "Digital cellular telecommunication system (Phase 2);
Modulation".
[47] GSM 05.05 Version 4.22.1: "Digital cellular telecommunication system (Phase
2); Radio transmission and reception".
[48] GSM 05.08 Version 4.21.1: "Digital cellular telecommunication system
(Phase 2); Radio subsystem link control".
[49] GSM 05.10 Version 4.9.0: "Digital cellular telecommunication system (Phase 2);
Radio subsystem synchronisation".
[50] GSM 07.01 Version 4.10.0: "Digital cellular telecommunication system
(Phase 2); General on Terminal Adaptation Functions (TAF) for Mobile Stations
(MS)".
Page 10
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
[51] GSM 08.08 Version 4.12.1: "Digital cellular telecommunications system
(Phase 2); Mobile-services Switching Centre - Base Station System (MSC -
BSS) interface Layer 3 specification".
[52] GSM 08.58 Version 4.9.0: "Digital cellular telecommunications system
(Phase 2); Base Station Controller - Base Transceiver Station (BSC - BTS)
interface Layer 3 specification".
[53] GSM 09.02 Version 4.18.0: "Digital cellular telecommunication system
(Phase 2); Mobile Application Part (MAP) specification".
[54] GSM 11.10-1 Version 4.24.0: "Digital cellular telecommunications system
(Phase 2); Mobile Station (MS) conformance specification; Part 1: Conformance
specification".
[55] GSM 11.10-2 Version 4.15.0: "Digital cellular telecommunications system
(Phase 2); Mobile Station (MS) conformance specification; Part 2: Protocol
Implementation Conformance Statement (PICS) Proforma specification".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this ETS, the following definitions apply:
Abstract Test Suite (ATS): Refer to ISO/IEC 9646-1 [1].
Implementation Under Test (IUT): Refer to ISO/IEC 9646-1 [1].
Partial Protocol Implementation eXtra Information for Testing (IXIT): Refer to ISO/IEC 9646-1 [1].
Point of Controls and Observations (PCO): Refer to ISO/IEC 9646-1 [1].
Protocol Implementation Conformance Statement (ICS): Refer to ISO/IEC 9646-1 [1].
System Under Test (SUT): Refer to ISO/IEC 9646-1 [1].
3.2 Abbreviations
For the purposes of this ETS, the following abbreviations apply:
ATS Abstract Test Suite
BI Invalid Behaviour tests
BO Inopportune Behaviour tests
BV Valid Behaviour tests
CA CApability tests
EDP-N Event Detection Point - Notification
EDP-R Event Detection Point - Request
ETS European Telecommunication Standard
FE Functional Entity
FSM Finite State Machine
ICS Implementation Conformance Statement
IUT Implementation Under Test
IXIT Implementation eXtra Information for Testing
PDU Protocol Data Unit
SUT System Under Test
TP Test Purpose
TSS Test Suite Structure
Further abbreviations used within GSM related ETS may be found in ETR 100.
Abbreviations for test case group names may be found in figure 1 and 2.
Page 11
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
4 Test Suite Structure (TSS)
4.1 Test suite naming convention
The test group identifier for each group and subgroup is built according to the scheme in figure 1.
Identifier: L3
= category: BIT BIT, Basic Interconnection tests (not used)
CA CA, Capability tests (not used)
BV BV, Valid Behaviour tests
BI-BOBI and BO, Invalid and Inopportune Behaviour tests
= group: IN Initial tests
ID Idle mode tests
RR Radio Resource management
MM Mobility Management
CC Call Control
SP Structured Procedures
SS Supplementary services
LLF Lower Layer Failures
UUE Unknown, Unforeseen or erroneous Elements
= group: CR Channel Request
AT IMSI detach and IMSI attach
SMT Sequenced MM / CC message transfer
EC Establishment Cause
IA Immediate assignment
PG Test of paging
MR Test of measurement report
ASS Test of the channel
HO Test of handover
FR Test of frequency redefinition
CMM Test of the channel mode modify procedure
CY Test of ciphering mode setting
CM Test of classmark
CHR Test of channel release
START Test of starting time
IDAU Identification and authentication
LU Location updating
CON MM connection
CCSMO State Machine Verification, Mobile Originating Call
CCSMT State Machine Verification, Mobile Terminating Call
SMICF State machine verification, In Call Functions
CRE Call Re-establishment
UUS User to user signalling
UPD Unknown protocol discriminator
TIS TI and skip indicator
UMT Undefined or unexpected message type
UIE Unforeseen information elements in the non-imperative
NMIE Non-semantical mandatory IE errors
CNR Unknown IE, comprehension not required
SB Spare bits
Page 12
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
= group: AC Handover / successful / active call
CUE Handover / successful / call under establishment
FSY Handover / successful / active call / finely synchronized
PRS Pre-synchronized handovers
PRF Protocol failures
ACC Location updating / accepted
REJ Location updating / rejected
ABN Location updating / abnormal cases
REL Location updating / release
PER Location updating / periodic
HPERLocation updating / periodic HPLMN search
IWAT Location updating / interworking of attach and periodic
EST MM connection / establishment
EXP MM connection / expiry
NWAB MM connection / abortion by the network
FRQPMM connection / follow-on request pending
U0 Mobile Originating Call U0 State
U0.1 Mobile Originating Call U0.1 MM Connection pending
U1 Mobile Originating Call U1 State
U3 Mobile Originating Call U3 State
U4 Mobile Originating Call U4 State
U10 Mobile Originating Call U10 State
U11 Mobile Originating Call U11 State
U12 Mobile Originating Call U12 State
U19 Mobile Originating Call U19 State
U0 Mobile Terminating Call U0 State
U6 Mobile Terminating Call U6 State
U9 Mobile Terminating Call U9 State
U7 Mobile Terminating Call U7 State
U8 Mobile Terminating Call U8 State
DTMFState machine verification, In Call Functions / transfer
CHC State machine verification, In Call Functions /
TICM State machine verification, In Call Functions / in-
OICM State machine verification, In Call Functions / in-
Figure 1: Test group identifier naming convention scheme
4.2 Suite Overview
Figure 2 shows the structure of the test suites for L3.
L3 ATS
BV BI/O
IN ID RR MM CC SP SS SMS LLF UUE
Figure 2: Test suite structure of the L3 tests
4.3 Test groups
4.3.1 Valid Behaviour tests (BV)
Predefined state transitions are considered as valid. The test purposes in the valid behaviour test
subgroup cover the verification of the normal and exceptional procedures of the various Finite State
Machines (FSMs), i.e. a valid behaviour test is a test where the message sequence and the message
contents are considered as valid.
4.3.2 Invalid Behaviour/Inopportune Behaviour tests (BI-BO)
This test sub group verifies that the Implementation Under Test (IUT) is able to react properly having
received an invalid Protocol Data Unit (PDU) or in the case an inopportune protocol event occurs. An
invalid PDU is defined as a syntactically incorrect message. An inopportune event is syntactically correct
but occurs when it is not expected, e.g. a correctly coded operation is received in a wrong state (the IUT
may respond Error UnexpectedComponentSequence).
Page 13
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
4.4 Test Step Structure
4.4.1 Preambles
The preamble is defined for each test purpose.
4.4.2 Postambles
After each test case the IUT shall be brought to the state as defined in the postamble for each test
purpose.
5 Test Purposes (TP)
For each conformance requirement a Test Purpose (TP) is defined. The test purposes are specified in the
ATS Dynamic part (annex A).
5.1 TP and test case naming convention
In order clearly to map the conformance requirements specified in the prETS 300 607-1 and TTCN test
cases in the ATS, the section numbers in the prETS 300 607-1 are used as test case names.
The identifier of each TP is identical to the name of the implemented TTCN test case.
"Test Purpose Identifier" = "Test Case Name" = TPI = TC_NN_A_B_C_D_E, where NN, A, B, C, D and E
are digits used in the corresponding section numbers of prETS 300 607-1. For example, the test case
name TC_26_5_6_2 is the TTCN specification corresponding to the conformance requirements in the
section 26.5.6.1.2 in the prETS 300 607-1. In case where the section has been implemented in more than
one test case sub numbering has been introduced. For example, the section 26.7.4.2.4 of
prETS 300 607-1, Location updating/rejected/national roaming testing is split into 5 test cases. The
corresponding TCs are identified as TC_26_7_4_2_4_1, TC_26_7_4_2_4_2, TC_26_7_4_2_4_3,
TC_26_7_4_2_4_4 and TC_26_7_4_2_4_5, respectively.
6 Abstract test method and test configurations
The distributed test method applies to the L3 MS testing. The test method uses a lower tester and a
Man-Machine Interface (MMI) as an upper tester at the SUT.
6.1 Test system model
The model of the L3 test system is based on the original protocol architecture at the air interface. The test
system consists conceptually of a lower tester LT, the L3 test programme (executable test suite), a L2
radio link emulator, a management functional unit, the L1 service provider and a TRx set (see figure 1).
Test operator
SUT
LT
L3 test programme
IUT
L3
PCO
L2
L2 emulator
Mngt
L1 L1
TRx set TRx
MS
Test system
Radio connection
Figure 3: Test system and distributed test method
Page 14
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
The LT provides the test environment and for test execution and the means of control and observation at
the L3 lower service boundary within the test system.
The L3 TTCN test specification uses the three LT interfaces to communicate with the MS, the system
under test, and with the other parts of the test system:
- Interface to the L2 emulator via the PCO;
- Interface to the management functional unit via TTCN test suite operations;
- Interface to the MS Man-Machine Interface (MMI) via a test operator.
6.2 Test Method
The PCO in the LT is defined as L2 SAP (SAP 0 + 3). The PCO has two FIFO queues (data buffers) to
store all sending and receiving test events. The L2 primitives in the ATS which constitute mainly the
interface to the L2 emulator are specified via the L2 primitives. In order to simulate multicell testing as
required in some test cases, the defined primitives are able to address individual cells of the test system
and the logic channels of each cell for the L3 message exchanges. The L2 emulator together with the
underlying L1 and the TRx set support all message exchanges via correct radio links.
The management function unit has three management functions:
• L2 and L1 management;
• Channel management;
• TRx management;
The interface to the management function unit is presented in the ATS via a set of test suite operations.
The major functions of the test suite management operations are:
• To load configuration parameters necessary for the test system.
• To control and get the necessary values of radio resources/ channels for tests.
The SUT (MS) has a more or less standardized MMI, such as keys, digital display, tones, etc. The ATS
uses such kind of functions to provoke some procedures or to observe simple results at the SUT side. A
human operator is needed during the test. The test system shall have an interface to the human operator
to enable the test co-ordination.
Page 15
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Annex A (normative): Layer 3 Abstract Test Suite
This ATS has been produced using the Tree and Tabular Combined Notation (TTCN) according to
ISO/IEC 9646-3 [3].
The ATS was developed on a separate TTCN software tool and therefore the TTCN tables are not
completely referenced in the contents table. The ATS itself contains a test suite overview part which
provides additional information and references.
A.1 The TTCN Graphical form (TTCN.GR)
The TTCN.GR representation of this ATS for Layer 3 is contained in an Adobe Portable Document
Format™ file (l3-4o0.PDF, contained in archive 6073_ea.ZIP) (Layer 3) which accompanies this ETS
(Part 3).
A.2 The TTCN Machine Processable form (TTCN.MP)
The TTCN.MP representation corresponding to this ATS for Layer 3 is contained in an ASCII file
(l3-4o0.mp, contained in archive 6073_ea.ZIP) (Layer 3) which accompanies this ETS (Part 3).
NOTE: According to ISO/IEC 9646-3 [3], in case of a conflict in interpretation of the
operational semantics of TTCN.GR and TTCN.MP, the operational semantics of the
TTCN.GR representation takes precedence.
Page 16
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Annex B (normative): Partial IXIT proforma
Notwithstanding the provisions of the copyright clause related to the text of this ETS, ETSI grants that
users of this ETS may freely reproduce the PIXIT proforma in this annex so that it can be used for its
intended purposes and may further publish the completed PIXIT.
Introduction
This partial IXIT proforma contained in this ETS, after augmented by the Test Realizer, is proposed to be
provided to the client for completion, when the related Abstract Test Suite is to be used against client's
Implementation Under Test (IUT).
Text in italics is comments for guidance for the production of a IXIT, and is not to be included in the actual
IXIT.
The completed IXIT will normally be used in conjunction with the completed ICS, as it adds precision to
the information provided by the ICS.
Page 17
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.1 Identification Summary
This table is completed by the test laboratory. The item "Contract References" is optional.
Table 1: Identification Summary
IXIT Reference Number
Test Laboratory Name
Date of Issue
Issued to (name of client)
Contract References
B.2 Abstract Test Suite Summary
In the following table the test laboratory provides the version number of the protocol specification and the
version number of ATS which are used in the conformance testing.
Table 2: ATS Summary
Protocol Specification ETS 300 557
Version of Protocol Specification
TSS & TP Specification ETS 300 607-1
Version of TSS & TP Specification
ATS Specification ETS 300 607-3
Version of ATS Specification
Abstract Test Method Remote Test Method
B.3 Test Laboratory
B.3.1 Test Laboratory Identification
The test laboratory provides the following information.
Table 3: Test Laboratory Identification
Name of Test Laboratory
Postal Address
Office address
Telephone Number
FAX Number
Page 18
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.3.2 Accreditation status of the test service
The test laboratory provides the following information.
Table 4: Accreditation status of the test service
Accreditation status
Accreditation Reference
B.3.3 Manager of Test Laboratory
The test laboratory provides the information about the manager of test laboratory in the following table.
Table 5: Manager of Test Laboratory
Name of Manager of Test Laboratory
Telephone Number
FAX Number
E-mail Address
B.3.4 Contact person of Test Laboratory
The test laboratory provides the information about the contact person of test laboratory in the following
table.
Table 6: Contact person of Test Laboratory
Name of Contact of Test Laboratory
Telephone Number
FAX Number
E-mail Address
Page 19
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.3.5 Means of Testing
In the table below, the test laboratory provides a statement of conformance of the Means Of Testing
(MOT) to the reference standardized ATS, and identifies all restrictions for the test execution required by
the MOT beyond those stated in the reference standardized ATS.
Table 7: Means of Testing
Means of Testing
Page 20
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.3.6 Instructions for Completion
In this table, the test laboratory provides any specific instructions necessary for completion and return of
the proforma from the client.
Table 8: Instruction for Completion
Instructions for Completion
Page 21
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.4 Client
B.4.1 Client Identification
The client provides the identification in the following table.
Table 9: Client Identification
Name of Client
Postal Address
Office Address
Telephone Number
FAX Number
B.4.2 Client Test Manager
In this table the client provides information about the test manager.
Table 10: Client Test Manager
Name of Client Test Manager
Telephone Number
FAX Number
E-mail Address
B.4.3 Client Contact person
In this table the client provides information about the test contact person.
Table 11: Client Contact person
Name of Client contact person
Telephone Number
FAX Number
E-mail Address
Page 22
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.4.4 Test Facilities Required
In the following table, the client records the particular facilities required for testing, if a range of facilities is
provided by the test laboratory.
Table 12: Test Facilities Required
Test Facilities Required
Page 23
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.5 System Under Test
B.5.1 SUT Information
The client provides information about the SUT in the table below.
Table 13: SUT Information
System Name
System Version
SCS Reference
Machine Configuration
Operating System Identification
IUT Identification
ICS Reference for the IUT
Page 24
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.5.2 Limitations of the SUT
In the table below, the client provides information explaining if any of the abstract tests cannot be
executed.
Table 14: Limitation of the SUT
Limitations of the SUT
Page 25
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.5.3 Environmental Conditions
In the table below the client provides information about any tighter environmental conditions for the correct
operation of the SUT.
Table 15: Environmental Conditions
Environmental Conditions
Page 26
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
B.6 Ancillary Protocols
This clause is completed by the client in conjunction with the test laboratory.
In the following tables, the client identifies relevant information concerning each ancillary protocol in the
SUT other than the IUT itself. One table for one ancillary protocol.
Based on the MOT the test laboratory should create question proforma for each ancillary protocol in the
blank space following each table. The information required is dependent on the MOT and the SUT, and
covers all the addressing, parameter values, timer values and facilities (relevant to ETSs) as defined by
the ICS for the ancillary protocol.
B.6.1 Ancillary Protocols 1
Table 16: Ancillary Protocol 1
Protocol Name ETS 300
Version number
ICS Reference (optional)
IXIT Reference (optional)
PCTR Reference (optional)
B.6.2 Ancillary Protocols 2
Table 17: Ancillary Protocol 2
Protocol Name ETS 300
Version number
ICS Reference (optional)
IXIT Reference (optional)
PCTR Reference (optional)
B.7 Protocol Layer Information for L3 of Mobile Station
B.7.1 Information provided for test purposes by the MS supplier
Item Description Type/Allowed Supported
values Value
TSPC_24DataF 2.4 k full rate data mode BOOLEAN
supported
TSPC_24DataH 2.4 k half rate data mode BOOLEAN
supported
TSPC_48DataF 4.8 k full rate data mode BOOLEAN
supported
TSPC_48DataH 4.8 k half rate data mode BOOLEAN
supported
TSPC_96Data 9.6 k full rate data mode BOOLEAN
supported
TSPC_Feat_A51 ciphering algorithm A5/1 BOOLEAN
supported
TSPC_Feat_A52 ciphering algorithm A5/2 BOOLEAN
supported
TSPC_AddCharSet A, B, C, D chars supported BOOLEAN
TSPC_AddInfo_PseudoSync Pseudo synchronised BOOLEAN
h supported
Page 27
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Item Description Type/Allowed Supported
values Value
TSPC_AlertInd alerting indication to the user BOOLEAN
supported
TSPC_SvcOnTCH at least one service on traffic BOOLEAN
channel supported
TSPC_SMS at least one short message BOOLEAN
service supported
TSPC_SS at least one supplementary BOOLEAN
service supported
TSPC_AutoAutoMode automatically enter automatic BOOLEAN
selection of PLMN mode
supported
TSPC_BasCharSet Chars 0-9, *, # supported BOOLEAN
TSPC_CalledNumDisp called number display BOOLEAN
supported
TSPC_DCS testing DCS1 800 BOOLEAN
TSPC_DetachOnPwrDn detach on power down BOOLEAN
supported
TSPC_DetachOnSIMRmv detach on SIM remove BOOLEAN
supported
TSPC_DispRcvSMS display of received SMS BOOLEAN
supported
TSPC_DualRate dual rate channel types BOOLEAN
supported
TSPC_EGSM both standard and extended BOOLEAN
GSM band supported
TSPC_EmgOnly the only circuit switched basic BOOLEAN
service is emergency call
TSPC_followOnReq follow-on request procedure BOOLEAN
supported
TSPC_HalfRateData half rate data supported BOOLEAN
TSPC_HalfRateSpeech half rate speech mode BOOLEAN
supported
TSPC_InCallMod In-Call modification supported BOOLEAN
TSPC_NoimmConn at least one service not BOOLEAN
support immediate connection
TSPC_Feat_FND FND feature supported BOOLEAN
TSPC_NonCallSS non call related supplementary BOOLEAN
service supported
TSPC_MTsvc at least one MT circuit BOOLEAN
switched basic service
supported
TSPC_MOsvc at least one MO circuit BOOLEAN
switched basic service
supported
TSPC_PGSM only standard GSM band BOOLEAN
supported
TSPC_RefusalCall refusal of call supported BOOLEAN
TSPC_ReplaceSMS replace SMS supported BOOLEAN
TSPC_ReplyProc (SMS) reply procedures BOOLEAN
supported
Page 28
ETS 300 607-3 (GSM 11.10-3 version 4.24.1): April 1999
Item Description Type/Allowed Supported
values Value
TSPC_RFAmp RF amplification supported BOOLEAN
TSPC_SDCCHOnly only SDCCH supported BOOLEAN
TSPC_Serv_SS_AoCC AOCC SS supported BOOLEAN
TSPC_Serv_SS_BAIC BAIC SS supported BOOLEAN
TSPC_Serv_SS_BI BI SS supported BOOLEAN
TSPC_Serv_SS_BICRoam BICRoam SS supported BOOLEAN
TSPC_Serv_SS_BAOC B
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...