SIST EN 13126-2:2011
(Main)Building hardware - Requirements and test methods for windows and doors height windows - Part 2: Window fastener handles
Building hardware - Requirements and test methods for windows and doors height windows - Part 2: Window fastener handles
This European Standard specifies requirements and test methods for durability, strength, security and functionality of window fastener handles.
This European Standard does not apply to the following hardware:
a) handles - primarily for Tilt & Turn, Tilt-First and Turn-Only hardware, refer to EN 13126-3;
b) electromechanical hardware.
Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 2: Fenstergriffe
Diese Europäische Norm legt die Anforderungen und Prüfverfahren für die Dauerfunktionstüchtigkeit, Festigkeit, Schutzwirkung und Funktionsweise von Fenstergriffen fest. Sie gilt nicht für die folgenden Baubeschläge:
a) Griffe überwiegend für Drehkipp-, Kippdreh- und Drehbeschläge — hierfür siehe EN 3126-3;
b) elektromechanische Beschläge.
Quincaillerie pour le bâtiment - Exigences et méthodes d'essai des ferrures de fenêtres et portes-fenêtres - Partie 2: Poignées à ergot de verrouillage
La présente Norme européenne spécifie les exigences et méthodes d'essai relatives à l'endurance, à la
résistance, à la sécurité des biens et à la fonctionnalité des poignées à ergot de verrouillage.
La présente Norme européenne ne s'applique pas aux ferrures suivantes :
a) poignées - principalement pour ferrures d'oscillo-battant, de battant-oscillant et d'ouvrant pivotant, se
reporter à l'EN 13126-3 ;
b) dispositifs électromécaniques.
Stavbno okovje - Zahteve in preskusne metode za okna in zastekljena vrata - 2. del: Okenska zapirala
Ta evropski standard določa zahteve in preskusne metode za vzdržljivost, moč, varnost in funkcionalnost okenskih zapiral.
Ta evropski standard ne velja za naslednje okovje:
a) zapirala – prvotno za nagni in obrni, najprej nagni in samo obrni okovje, glej EN 13126-3,
b) elektromehansko okovje.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stavbno okovje - Zahteve in preskusne metode za okna in zastekljena vrata - 2. del: Okenska zapiralaBaubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 2: FenstergriffeQuincaillerie pour le bâtiment - Exigences et méthodes d'essai des ferrures de fenêtres et portes-fenêtres - Partie 2: Poignées à ergot de verrouillageBuilding hardware - Requirements and test methods for windows and doors height windows - Part 2: Window fastener handles91.190Stavbna opremaBuilding accessoriesICS:Ta slovenski standard je istoveten z:EN 13126-2:2011SIST EN 13126-2:2011en,fr,de01-december-2011SIST EN 13126-2:2011SLOVENSKI
STANDARDSIST-TS CEN/TS 13126-2:20051DGRPHãþD
SIST EN 13126-2:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13126-2
October 2011 ICS 91.190 Supersedes CEN/TS 13126-2:2004English Version
Building hardware - Requirements and test methods for windows and doors height windows - Part 2: Window fastener handles
Quincaillerie pour le bâtiment - Exigences et méthodes d'essai des ferrures de fenêtres et portes-fenêtres - Partie 2: Poignées à ergot de verrouillage
Baubeschläge - Beschläge für Fenster und Fenstertüren - Anforderungen und Prüfverfahren - Teil 2: Einreibverschlüsse This European Standard was approved by CEN on 26 August 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13126-2:2011: ESIST EN 13126-2:2011
EN 13126-2:2011 (E) 2 Contents Page Foreword . 31Scope. 62Normative references . 63Terms and definitions . 64Classification . 74.1General . 74.2Category of use (1 – first digit) . 74.3Durability (2 – second digit) . 74.4Mass (3 – third digit) . 74.5Fire resistance (4 – fourth digit) . 74.6Safety in use (5 – fifth digit) . 84.7Corrosion resistance (6 – sixth digit) . 84.8Security (7 – seventh digit) . 84.9Application (8 – eighth digit) . 84.10Test sizes – Size limitations (9 – ninth digit) . 84.11Example of classification for window fastener handles (EN 13126-2) . 95Requirements . 95.1General . 95.2Operating torque . 95.3Torsion strength . 95.4Tensile strength - eccentric . 95.5Simulated pressure . 105.6Pull-in . 105.7Durability . 105.8Security . 105.8.1General . 105.8.2Durability of the locking mechanism . 115.8.3Torque resistance of the locking mechanism / solid fixing . 115.8.4Twist-off resistance . 115.8.5Forcing off resistance. 116Test equipment . 127Test procedure . 127.1Samples . 127.2Operating torque test procedure . 127.3Torsion strength test procedure . 137.4Tensile strength test procedure – eccentric . 137.5Simulated pressure test procedure . 137.6Pull-in test . 137.7Durability test procedure. 147.8Corrosion resistance . 147.9Locking mechanism durability test . 147.10Torque resistance of the locking mechanism / solid fixing test . 147.11Test - Resistance against twisting-off and forcing-off . 15Annex A (informative)
Tests method diagrams . 16Annex B (informative)
Figures . 18 SIST EN 13126-2:2011
EN 13126-2:2011 (E) 3 Foreword This document (EN 13126-2:2011) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the latest by April 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 13126-2:2004. The major changes of this document to CEN/TS 13126-2:2003 are: - the addition of
three grades and three extensions
for the security - the addition of security requirements and the corresponding tests - the modification of the number of test samples (8 instead of 3) - the increase to 550 cycles/h rate for the durability test. 4.8 Security (7 – seventh digit) Three grades have been added into this draft to give similarity with prEN13126-3, three extensions have also been added for the locking style of the handle. Grade 0: Without security Grade 1: 35 Nm resistance against twisting-off and forcing-off Grade 2: 100 Nm resistance against twisting-off and forcing-off Extension 0: No locking mechanism Extension 1: Non-key operated locking mechanism (e.g. ‘PTO’: Push-to-open) Extension 2: Key-operated locking mechanism
SIST EN 13126-2:2011
EN 13126-2:2011 (E) 4 Table 1 – Security Grade Description 0/0 No requirements against twisting-off and forcing-off / without locking mechanism 1/1 35 Nm resistance against twisting-off and forcing-off / Non-key operated locking mechanism (‘PTO’: push to open) 1/2 35 Nm resistance against twisting-off and forcing-off / Key operated locking mechanism 2/1 100 Nm resistance against twisting-off and forcing-off / Non-key operated locking mechanism (‘PTO’: push to open) 2/2 100 Nm resistance against twisting-off and forcing-off / Key operated locking mechanism Digit seven will now contain two classifications i.e. 1/2 Digit 7 security - grade 1/2; rated as resisting 35 Nm twisting-off and forcing-off force, and has key operated locking mechanism. With the addition of locking handles several additional points have been included: 5.8.1 General 5.8.2 Durability of the locking mechanism – new requirement 5.8.3 Torque resistance of the locking mechanism / Solid fixing – new requirement 5.8.4 Twist-off resistance – new requirement 5.8.5 Forcing off resistance – new requirement 7.1 Samples – Eight samples are to be submitted apposed to three 7.7
Durability Test Procedure, the rate that the cycle test is carried out has been increased to 550 cycles/h in line with prEN13126-3 7.9
Locking Mechanism durability test – new requirement 7.10 Torque resistance of the locking mechanism / solid fixing test – new requirement 7.11 Test – Resistance against twisting-off and forcing-off – new requirement In general there has been a reduction in the tolerance band within the draft over the last published standard. A full contribution to the preparation of this European Standard has been made by the European manufacturers´ organization ‘ARGE’ and national standards bodies. EN 13126 Building hardware — Requirements and test methods for windows and doors height windows consists of the following parts: Part 1: Requirements common to all types of hardware SIST EN 13126-2:2011
EN 13126-2:2011 (E) 5 Part 2: Window fastener handles1) Part 3: Manoeuvring fittings for espagnolette bolts/sliding button1) Part 4: Espagnolettes Part 5: Devices that restrict the opening of windows1) Part 6: Variable geometry stay hinges (with or without a friction stay) Part 7: Finger catches Part 8: Tilt&Turn, Tilt-First and Turn-Only hardware Part 9: Pivot hinges1) Part 10: Arm-balancing systems Part 11: Top hung projecting reversible hardware Part 12: Side hung projecting reversible hardware Part 13: Sash balances1) Part 14: Sash fasteners1) Part 15: Rollers for horizontal sliding and sliding folding windows and doors Part 16: Hardware for Lift&Slide windows and doors Part 17: Hardware for Tilt&Slide windows and doors Part 18: Requirements and test procedures for durability, strength, security and functionality of Fan light openers for windows and door height windows Part 19: Sliding Closing Devices The performance tests incorporated in this standard are considered to be reproducible and as such will provide a consistent and objective assessment of the performance of these products throughout CEN Member States. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
1) Under revision currently on Technical specification. SIST EN 13126-2:2011
EN 13126-2:2011 (E) 6 1 Scope This European Standard specifies requirements and test methods for durability, strength, security and functionality of window fastener handles. This European Standard does not apply to the following hardware: a) handles - primarily for Tilt & Turn, Tilt-First and Turn-Only hardware, refer to EN 13126-3; b) electromechanical hardware. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1670, Building hardware — Corrosion resistance — Requirements and test methods EN 12519:2004, Windows and pedestrian doors — Terminology EN 13126-1:2006, Building hardware — Requirements and test methods for windows and doors height windows — Part 1: Requirements common to all types of hardware 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13126-1:2006 and
EN 12519:2004 and the following apply. 3.1 window fastener handle operating device, where applicable with releasable and / or locking mechanism, to hold the window in a closed position NOTE
Also known as Cockspur handles. 3.2 spur device projecting from the handle that interacts with the compression wedge / keeper to close the window to give the desired pull-in 3.3 pull-in distance the sash is moved towards the frame during operation of a window fastener handle from the initial contact of the handle spur to the fully closed position 3.4 non-key operated locking mechanism device within the handle assembly that when engaged prevents movement of the handle from the locked position EXAMPLE ‘push-to-open’, button, thumb turn SIST EN 13126-2:2011
EN 13126-2:2011 (E) 7 3.5 locking mechanism key operated device within the handle assembly that when engaged prevents movement of the handle from the locked position (e.g. locking cylinder or key) 3.6 compression wedge / keeper component applied to the window in a position to allow interaction with the handle spur to hold the window in a closed position 3.7 weatherseal compressible gasket between the sash and the frame that prevents air and water ingress 3.8 closing conditions 3.8.1 closed position position in which the moving part of the window is resting against the frame or weather seal on all sides and the fastening system is not engaged 3.8.2 closed and fastened position position in which the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.