SIST EN ISO 7214:2007
(Main)Cellular plastics - Polyethylene - Methods of test (ISO 7214:2007)
Cellular plastics - Polyethylene - Methods of test (ISO 7214:2007)
This International Standard specifies methods for testing flexible and semi-rigid cellular plastics made from polyethylene. Cellular plastics containing copolymers of ethylene or blends of polymers with polyethylene may also be tested by the procedures of this International Standard provided these materials have characteristics similar to polyethylene as described in ISO 1872-1, or copolymers of ethylene as described in ISO 4613-1. Mandatory tests suitable for characterization of cellular polyethylene, regardless of end use, are described in Clause 7. Optional tests for the determination of properties that are relevant to certain uses are described in Clause 8.
Schaumstoffe - Polyethylen - Prüfverfahren (ISO 7214:2007)
1.1 Diese Internationale Norm legt Prüfverfahren für weich-elastische und halbharte Schaumstoffe aus Polyethylen fest. Schaumstoffe, die Ethylen-Copolymere oder Mischungen aus Polymeren mit Polyethylen enthalten, dürfen ebenso nach den Verfahren dieser Internationalen Norm geprüft werden, vorausgesetzt, diese Materialien haben ähnliche Eigenschaften wie Polyethylen nach ISO 1872-1 oder Ethylen-Copolymere nach ISO 4613-1.
1.2 Im Abschnitt 7 sind grundsätzliche Prüfungen festgelegt, die für die Kennzeichnung der Polyethylenschaumstoffe geeignet sind, ohne die Anwendung zu berücksichtigen. Abschnitt 8 enthält die ergänzenden Prüfungen zur Bestimmung von Eigenschaften, die sich auf bestimmte Einsatzgebiete beziehen.
Plastiques alvéolaires - Polyéthylene - Méthodes d'essai (ISO 7214:2007)
L'ISO 7214:2007 spécifie des méthodes d'essai applicables aux matériaux plastiques alvéolaires souples et semi-rigides, fabriquées en polyéthylène. Les matériaux plastiques alvéolaires contenant des copolymères de l'éthylène ou des mélanges de polymères et de polyéthylène peuvent également être soumis à l'essai conformément aux modes opératoires spécifiés dans l'ISO 7214:2007, à condition qu'elles possèdent des caractéristiques similaires à celles du polyéthylène ou à celles des copolymères de l'éthylène.
Deux catégories d'essais sont spécifiées: les essais de base, qui permettent de caractériser les polyéthylènes alvéolaires indépendamment de leur destination finale, et les essais supplémentaires, qui permettent de déterminer les propriétés qui sont utiles dans le cas de certaines utilisations.
Penjeni polimerni materiali - Polietilen - Preskusne metode (ISO 7214:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 7214:2007
01-september-2007
1DGRPHãþD
SIST EN ISO 7214:2001
Penjeni polimerni materiali - Polietilen - Preskusne metode (ISO 7214:2007)
Cellular plastics - Polyethylene - Methods of test (ISO 7214:2007)
Schaumstoffe - Polyethylen - Prüfverfahren (ISO 7214:2007)
Plastiques alvéolaires - Polyéthylene - Méthodes d'essai (ISO 7214:2007)
Ta slovenski standard je istoveten z: EN ISO 7214:2007
ICS:
83.100 Penjeni polimeri Cellular materials
SIST EN ISO 7214:2007 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 7214
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2007
ICS 83.100 Supersedes EN ISO 7214:2000
English Version
Cellular plastics - Polyethylene - Methods of test (ISO
7214:2007)
Plastiques alvéolaires - Polyéthylène - Méthodes d'essai Schaumstoffe - Polyethylen - Prüfverfahren (ISO
(ISO 7214:2007) 7214:2007)
This European Standard was approved by CEN on 21 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7214:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 7214:2007 (E)
Foreword
This document (EN ISO 7214:2007) has been prepared by Technical Committee ISO/TC 61
"Plastics" in collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of
which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by December 2007, and conflicting national
standards shall be withdrawn at the latest by December 2007.
This document supersedes EN ISO 7214:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United
Kingdom.
Endorsement notice
The text of ISO 7214:2007 has been approved by CEN as EN ISO 7214:2007 without any
modifications.
2
---------------------- Page: 3 ----------------------
INTERNATIONAL ISO
STANDARD 7214
Third edition
2007-06-15
Cellular plastics — Polyethylene —
Methods of test
Plastiques alvéolaires — Polyéthylène — Méthodes d'essai
Reference number
ISO 7214:2007(E)
©
ISO 2007
---------------------- Page: 4 ----------------------
ISO 7214:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 5 ----------------------
ISO 7214:2007(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Test specimens . 2
4 Conditioning. 2
5 Atmosphere during test . 2
6 Measurement of dimensions . 3
7 Mandatory tests . 3
7.1 Apparent density. 3
7.2 Compressive stress. 3
7.3 Compression set. 3
7.4 Tensile strength and elongation . 3
7.5 Dimensional stability at elevated temperature . 4
7.6 Water absorption . 4
7.7 Burning characteristics. 5
8 Optional tests . 6
8.1 Dynamic cushioning performance. 6
8.2 Compressive creep. 6
8.3 Thermal conductivity. 6
8.4 Water-vapour transmission . 6
8.5 Dynamic stiffness . 6
8.6 Cell count. 6
8.7 Tear strength . 6
8.8 Permanent set after repeated compression. 8
9 Test report . 8
Annex A (normative) Cell count procedure. 10
© ISO 2007 – All rights reserved iii
---------------------- Page: 6 ----------------------
ISO 7214:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 7214 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 10, Cellular plastics.
This third edition cancels and replaces the second edition (ISO 7214:1998), which has been technically
revised.
iv © ISO 2007 – All rights reserved
---------------------- Page: 7 ----------------------
INTERNATIONAL STANDARD ISO 7214:2007(E)
Cellular plastics — Polyethylene — Methods of test
1 Scope
1.1 This International Standard specifies methods for testing flexible and semi-rigid cellular plastics made
from polyethylene. Cellular plastics containing copolymers of ethylene or blends of polymers with polyethylene
may also be tested by the procedures of this International Standard provided these materials have
characteristics similar to polyethylene as described in ISO 1872-1, or copolymers of ethylene as described in
ISO 4613-1.
1.2 Mandatory tests suitable for characterization of cellular polyethylene, regardless of end use, are
described in Clause 7. Optional tests for the determination of properties that are relevant to certain uses are
described in Clause 8.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 845:2006, Cellular plastics and rubbers — Determination of apparent density
ISO 1663, Rigid cellular plastics — Determination of water vapour transmission properties
ISO 1798, Flexible cellular polymeric materials — Determination of tensile strength and elongation at break
ISO 1856, Flexible cellular polymeric materials — Determination of compression set
ISO 1872-1, Plastics — Polyethylene (PE) moulding and extrusion materials — Part 1: Designation system
and basis for specifications
ISO 1923, Cellular plastics and rubbers — Determination of linear dimensions
ISO 2796, Cellular plastics, rigid — Test for dimensional stability
ISO 2896, Rigid cellular plastics — Determination of water absorption
ISO 3386-1, Polymeric materials, cellular flexible — Determination of stress-strain characteristics in
compression — Part 1: Low-density materials
ISO 3582, Flexible cellular polymeric materials — Laboratory assessment of horizontal burning characteristics
of small specimens subjected to a small flame
ISO 4613-1, Plastics — Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials — Part 1:
Designation and specification
ISO 4651, Cellular rubbers and plastics — Determination of dynamic cushioning performance
ISO 7850:1986, Cellular plastics, rigid — Determination of compressive creep
© ISO 2007 – All rights reserved 1
---------------------- Page: 8 ----------------------
ISO 7214:2007(E)
ISO 8301, Thermal insulation — Determination of steady-state thermal resistance and related properties —
Heat flow meter apparatus
ISO 8302, Thermal insulation — Determination of steady-state thermal resistance and related properties —
Guarded hot plate apparatus
ISO 8497, Thermal insulation — Determination of steady-state thermal transmission properties of thermal
insulation for circular pipes
ISO 9772, Cellular plastics — Determination of horizontal burning characteristics of small specimens
subjected to a small flame
3 Test specimens
The specimens shall be cut so that the edges are clean and the sides are planar and normal to the surface.
The specimens shall be cut from the sample so that a representative value is determined for each physical
property investigated. With anisotropic samples, take specimens in the appropriate direction.
Clauses 7 and 8 outline the requirements for the number of specimens, their shape and their dimensions.
Unless otherwise required by a specific test method, the surfaces of the specimens shall be the same as the
surface of the material in normal use.
4 Conditioning
Unless otherwise specified in Clause 7 or 8, specimens shall be conditioned for a minimum of 24 h at
(23 ± 2) °C and (50 ± 10) % relative humidity
or
+20
(23 ± 5) °C and 50 % relative humidity
−10
or
+20
(27 ± 5) °C and 65 % relative humidity.
−10
NOTE Some materials may require up to 30 days ageing after manufacture for the physical properties to stabilize.
5 Atmosphere during test
Unless otherwise specified, testing shall be carried out under the following conditions:
(23 ± 2) °C and (50 ± 10) % relative humidity
or
+20
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.