SIST EN IEC 61169-64:2020

Radio frequency connectors - Part 64: Sectional specification - RF coaxial connectors with 0,8 mm inner diameter of outer conductor - Characteristic impedance 50 Ω (type 0,8) (IEC 61169-64:2019)

EN-IEC 61169-64, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for IEC 61169 (all parts) coaxial connectors with 0,8 mm coupling. The connectors are used with cables with characteristic impedance 50 O in an operating frequency range up to 145 GHz. The connectors are widely used in communications and measurements. It describes the interface dimensions for general purpose connectors with gauging information and the mandatory tests selected from IEC 61169-1, applicable to all detail specifications relative to type 0,8 connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers all tests schedules and inspection requirements. All un-dimensioned pictorial configurations are for reference purpose only.

ochfrequenz-Steckverbinder - Teil 64: Rahmenspezifikation für koaxiale HF-Steckverbinder mit 0,8 mm Innendurchmesser des Außenleiters - Wellenwiderstand 50 Ω (Typ 0,8) (IEC 61169-64:2019)

Connecteurs pour fréquences radioélectriques - Partie 64: Spécification intermédiaire - Connecteurs RF coaxiaux avec un conducteur extérieur disposant d’un diamètre intérieur de 0,8 mm - Impédance caractéristique de 50 Ω (type 0,8) (IEC 61169-64:2019)

l'IEC 61169-64:2019, qui est une spécification intermédiaire (SS), fournit des informations et des règles en vue de l'établissement de spécifications particulières (DS) relatives aux connecteurs coaxiaux de la série IEC 61169 (toutes les parties) avec un couplage de 0,8 mm.
Les connecteurs sont utilisés avec des câbles disposant d’une impédance caractéristique de 50 Ω dans une plage de fréquences de fonctionnement allant jusqu’à 145 GHz. Les connecteurs sont largement répandus dans les domaines des communications et des mesures.
Elle décrit les dimensions d'interface pour les connecteurs d'usage général, ainsi que des informations concernant les calibres et les essais obligatoires choisis dans l'IEC 61169-1, applicables à toutes les spécifications particulières relatives aux connecteurs de type 0,8.
La présente spécification indique les caractéristiques de performance recommandées à prendre en compte pour la rédaction d’une spécification particulière et elle couvre tous les programmes d'essais et les exigences de contrôle.

Radiofrekvenčni konektorji - 64. del: Področna specifikacija - Radiofrekvenčni (RF) koaksialni konektorji z notranjim premerom 0,8 mm zunanjega vodnika - Karakteristična impedanca 50 ohm (tip 0,8) (IEC 61169-64:2019)

Standard EN-IEC 61169-64, ki je področna specifikacija (SS), podaja informacije in določa pravila za pripravo podrobnih specifikacij (DS) za koaksialne konektorje IEC 61169 z 0,8-milimetrskim spojem. Konektorji se uporabljajo s kabli z značilno impedanco 50 O v frekvenčnem območju delovanja do 145 GHz. Priključki se pogosto uporabljajo v komunikacijah in meritvah. Opisuje dimenzije vmesnika za konektorje za splošno uporabo z informacijami o merjenju in obvezne preskuse, izbrane iz standarda IEC 61169-1, ki se uporabljajo za vse podrobne specifikacije v zvezi s konektorji tipa 0,8. Ta specifikacija določa priporočene lastnosti, ki jih je treba upoštevati pri pripravi podrobnih specifikacij, ter zajema vse urnike preskusov in zahteve za pregled. Vse nedimenzionirane slikovne konfiguracije so podane samo za referenčne namene.

General Information

• Status: Published
• Publication Date: 26-Nov-2019
• ICS: 33.120.30 - RF connectors
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 20-Nov-2019
• Due Date: 25-Jan-2020
• Completion Date: 27-Nov-2019
• Ref Project: EN IEC 61169-64:2019 - Radio frequency connectors - Part 64: Sectional specification - RF coaxial connectors with 0,8 mm inner diameter of outer conductor - Characteristic impedance 50 Ω (type 0,8)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61169-64:2020
01-januar-2020
Radiofrekvenčni konektorji - 64. del: Področna specifikacija - Radiofrekvenčni (RF)
koaksialni konektorji z notranjim premerom 0,8 mm zunanjega vodnika -
Karakteristična impedanca 50 ohm (tip 0,8) (IEC 61169-64:2019)
Radio frequency connectors - Part 64: Sectional specification - RF coaxial connectors
with 0,8 mm inner diameter of outer conductor - Characteristic impedance 50 Ω (type
0,8) (IEC 61169-64:2019)
ochfrequenz-Steckverbinder - Teil 64: Rahmenspezifikation für koaxiale HF-
Steckverbinder mit 0,8 mm Innendurchmesser des Außenleiters - Wellenwiderstand 50
Ω (Typ 0,8) (IEC 61169-64:2019)
Connecteurs pour fréquences radioélectriques - Partie 64: Spécification intermédiaire -
Connecteurs RF coaxiaux avec un conducteur extérieur disposant d’un diamètre
intérieur de 0,8 mm - Impédance caractéristique de 50 Ω (type 0,8) (IEC 61169-64:2019)
Ta slovenski standard je istoveten z: EN IEC 61169-64:2019
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 61169-64:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61169-64:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 61169-64:2020


EUROPEAN STANDARD EN IEC 61169-64

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2019
ICS 33.120.30

English Version
Radio frequency connectors - Part 64: Sectional specification -
RF coaxial connectors with 0,8 mm inner diameter of outer
conductor - Characteristic impedance 50 Ω (type 0,8)
(IEC 61169-64:2019)
Connecteurs pour fréquences radioélectriques - Partie 64: Hochfrequenz-Steckverbinder - Teil 64:
Spécification intermédiaire - Connecteurs RF coaxiaux avec Rahmenspezifikation für koaxiale HF-Steckverbinder mit 0,8
un conducteur extérieur disposant d'un diamètre intérieur mm Innendurchmesser des Außenleiters -
de 0,8 mm - Impédance caractéristique de 50 Ω (type 0,8) Wellenwiderstand 50 Ω (Typ 0,8)
(IEC 61169-64:2019) (IEC 61169-64:2019)
This European Standard was approved by CENELEC on 2019-10-17. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61169-64:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61169-64:2020
EN IEC 61169-64:2019 (E)
European foreword
The text of document 46F/469/FDIS, future edition 1 of IEC 61169-64, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-64:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-07-17
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-10-17
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61169-64:2019 was approved by CENELEC as a European
Standard without any modification.


2

---------------------- Page: 4 ----------------------
SIST EN IEC 61169-64:2020
EN IEC 61169-64:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 62037-3 -  Passive RF and microwave devices, EN 62037-3 -
intermodulation level measurement - Part
3: Measurement of passive intermodulation
in coaxial connectors

3

---------------------- Page: 5 ----------------------
SIST EN IEC 61169-64:2020

---------------------- Page: 6 ----------------------
SIST EN IEC 61169-64:2020



IEC 61169-64

®


Edition 1.0 2019-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Radio-frequency connectors –

Part 64: Sectional specification – RF coaxial connectors with 0,8 mm inner

diameter of outer conductor – Characteristic impedance 50 Ω (type 0,8)




Connecteurs pour fréquences radioélectriques –

Partie 64: Spécification intermédiaire – Connecteurs RF coaxiaux avec un


conducteur extérieur disposant d’un diamètre intérieur de 0,8 mm – Impédance

caractéristique de 50 Ω (type 0,8)












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.30 ISBN 978-2-8322-7311-1




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61169-64:2020
– 2 – IEC 61169-64:2019  IEC 2019
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Mating face and gauge information . 7
4.1 Dimensions – General connectors . 7
4.1.1 Connector with pin-centre conductor . 7
4.1.2 Connector with socket-centre contact . 8
4.2 Gauges for general purpose connectors . 9
4.2.1 Gauge pins for socket centre contact . 9
4.2.2 Test procedure . 9
4.3 Dimensions – Standard test connectors – Grade 0 . 10
4.3.1 Connector with pin-centre contact . 10
4.3.2 Connector with socket-centre contact . 11
5 Quality assessment procedures . 12
5.1 General . 12
5.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) . 12
5.3 Test schedule and inspection requirements. 14
5.3.1 Acceptance tests . 14
5.3.2 Periodic tests . 14
5.4 Procedures for the quality conformance . 15
5.4.1 Quality conformance inspection . 15
5.4.2 Qualification approval and its maintenance . 16
6 Instructions for preparation of detail specifications . 16
6.1 General . 16
6.2 Identification of the component . 16
6.3 Performances . 16
6.4 Marking, ordering information and related matters . 16
6.5 Selection of tests, test conditions and severities . 17
6.6 Blank detail specification pro-forma for type 0,8 connector . 17
7 Marking . 21
7.1 Marking of component . 21
7.2 Marking and contents of package . 22

Figure 1 – Connector with pin centre conductor . 7
Figure 2 – Connector with socket centre conductor . 8
Figure 3 – Gauge pin for socket-centre contact . 9
Figure 4 – Connector with pin centre conductor . 10
Figure 5 – Connector with socket centre conductor . 11

Table 1 – Dimensions of connector with pin-centre contact . 7
Table 2 – Dimensions of connector with socket-centre conductor . 8
Table 3 – Dimensions of gauge pin for socket-centre contact . 9
Table 4 – Dimensions of connector with pin-centre contact . 10

---------------------- Page: 8 ----------------------
SIST EN IEC 61169-64:2020
IEC 61169-64:2019  IEC 2019 – 3 –
Table 5 – Dimensions of connector with socket-centre contact . 11
Table 6 – Rating and characteristics . 12
Table 7 – Acceptance tests . 14
Table 8 – Periodic tests . 15

---------------------- Page: 9 ----------------------
SIST EN IEC 61169-64:2020
– 4 – IEC 61169-64:2019  IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 64: Sectional specification – RF coaxial connectors with 0,8 mm inner
diameter of outer conductor – Characteristic impedance 50 Ω (type 0,8)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-64 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
RF connectors, RF and microwave passive components and accessories.
The text of this standard is based on the following documents:
FDIS Report on voting
46F/469/FDIS 46F/485/RVD

Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------
SIST EN IEC 61169-64:2020
IEC 61169-64:2019  IEC 2019 – 5 –
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------
SIST EN IEC 61169-64:2020
– 6 – IEC 61169-64:2019  IEC 2019
RADIO-FREQUENCY CONNECTORS –

Part 64: Sectional specification – RF coaxial connectors with 0,8 mm inner
diameter of outer conductor – Characteristic impedance 50 Ω (type 0,8)



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for IEC 61169 (all parts) coaxial connectors
with 0,8 mm coupling.
The connectors are used with cables with characteristic impedance 50 Ω in an operating
frequency range up to 145 GHz. The connectors are widely used in communications and
measurements.
It describes the interface dimensions for general purpose connectors with gauging information
and the mandatory tests selected from IEC 61169-1, applicable to all detail specifications
relative to type 0,8 connectors.
This specification indicates the recommended performance characteristics to be considered
when writing a DS and covers all tests schedules and inspection requirements.
NOTE Dimension are in mm, however original dimensions were in inches.
All un-dimensioned pictorial configurations are for reference purpose only.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 61169-1:2013, Radio-frequency connectors – Part 1: Generic specification – General
requirements and measuring methods
IEC 62037-3, Passive RF and microwave devices, intermodulation level measurement –
Part 3: Measurement of passive intermodulation in coaxial connectors
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp

---------------------- Page: 12 ----------------------
SIST EN IEC 61169-64:2020
IEC 61169-64:2019  IEC 2019 – 7 –
4 Mating face and gauge information
4.1 Dimensions – General connectors
4.1.1 Connector with pin-centre conductor
The mating face of connector with pin centre contact is shown in Figure 1 and its dimensions
are shown in Table 1.


a) Cross sectional view of connector b) Cross sectional view of centre conductor
Figure 1 – Connector with pin centre conductor
Table 1 – Dimensions of connector with pin-centre contact
mm
Ref.
Min. Max.
a 1,010 0 1,490 0
b 2,430 0 2,450 0
a
c 0,003 0 0,050 0
d 1,490 0 1,570 0
e 0,120 0 0,200 0
f - 0,020 0
g 37° 42°
h 0,345 0 0,351 0
j 0,364 0 0,416 0
k 0,060 0 0,100 0
l 3,320 0 3,400 0
m 1,890 0 1,898 0
n 0,797 0 0,803 0
p 0,197 0 0,203 0
q 0,360 0 0,440 0
Applicable for inner and outer contact for a 50 Ω nominal impedance
a
 Measurement uncertainty of inner conductor recession should be considered in the measurement.

---------------------- Page: 13 ----------------------
SIST EN IEC 61169-64:2020
– 8 – IEC 61169-64:2019  IEC 2019
4.1.2 Connector with socket-centre contact
Interface of connector with socket-centre contact is shown in Figure 2, dimensions are shown
in Table 2.


a) Cross sectional view of connector b) Cross sectional view of centre conductor
Figure 2 – Connector with socket centre conductor
Table 2 – Dimensions of connector with socket-centre conductor
mm
Ref.
Min. Max.
a 2,220 0 2,380 0
b 0,360 0 0,440 0
c 0,800 0
a
d 0,003 0 0,050 0
e 1,904 0 1,912 0
f 0,797 0 0,803 0
g - 0,011 0
h 0,020 0 0,060 8
j 0,056 0 0,120 0
k 0,345 0 0,351 0
l 3,000 0
m 2,360 0 2,400 0
n 1,280 0 1,360 0
Applicable for inner and outer contact for a 50 Ω nominal impedance resilient to meet the requirements with
gauge pins for socket centre contact expand to meet the requirements with gauge rings for socket outer contact.
a
Measurement uncertainty of inner conductor recession should be considered in the measurement.

---------------------- Page: 14 ----------------------
SIST EN IEC 61169-64:2020
IEC 61169-64:2019  IEC 20
...