SIST EN 301 908-19 V6.2.1:2013
(Main)IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 19: OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)
IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 19: OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)
The present document applies to the following radio equipment type:
- User Equipment for IMT-2000 OFDMA TDD WMAN (Mobile WiMAX) operating in TDD mode. This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive 1999/5/EC [i.2] may apply to equipment within the scope of the present document.
Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 19. del: Uporabniška oprema TDD OFDMA TDD WMAN (mobilni WiMAX)
Ta dokument se uporablja za radijsko opremo naslednje vrste:
– uporabniška oprema za IMT-2000 OFDMA TDD WMAN (mobilni WiMAX), ki deluje v načinu TDD. Ta vrsta radijske opreme lahko deluje v vseh delih frekvenčnih pasov iz preglednice 1-1.
Ta dokument zajema določbe člena 3.2 Direktive 1999/5/ES [i.2] (direktive R&TTE), ki navaja, da »[...] mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.« Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 Direktive 1999/5/ES [i.2] (Direktive R&TTE).
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.PRELOQL:L0$;IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 19: OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-19 Version 6.2.1SIST EN 301 908-19 V6.2.1:2013en01-oktober-2013SIST EN 301 908-19 V6.2.1:2013SLOVENSKI
STANDARD
SIST EN 301 908-19 V6.2.1:2013
ETSI EN 301 908-19 V6.2.1 (2013-06) IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 19: OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)
Harmonized European Standard SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)2
Reference REN/MSG-TFES-010-19 Keywords IMT, IMT-2000, mobile, OFDMA, radio, regulation, TDD, WiMAX, WMAN ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 9 3.3 Abbreviations . 9 4 Essential requirements specification . 10 4.1 Environmental profile . 10 4.2 Conformance requirements . 10 4.2.1 Introduction. 10 4.2.2 Transmitter Maximum Output Power . 10 4.2.2.1 Definition . 10 4.2.2.2 Limits . 10 4.2.2.3 Conformance . 10 4.2.3 Transmitter Spectrum Emission Mask . 11 4.2.3.1 Definition . 11 4.2.3.2 Limits . 11 4.2.3.2.1 Requirements for 5 MHz channel bandwidth . 11 4.2.3.2.2 Requirements for 10 MHz channel bandwidth . 11 4.2.3.3 Conformance . 12 4.2.4 Transmitter Spurious Emissions . 12 4.2.4.1 Definition . 12 4.2.4.2 Limits . 12 4.2.4.2.1 Requirements for 5 MHz channel bandwidth . 12 4.2.4.2.2 Requirements for 10 MHz channel bandwidth . 13 4.2.4.2.3 Requirements for UE Coexistence. 13 4.2.4.3 Conformance . 13 4.2.5 Transmitter Minimum Output Power . 13 4.2.5.1 Definition . 13 4.2.5.2 Limits . 13 4.2.5.3 Conformance . 13 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 14 4.2.6.1 Definition . 14 4.2.6.2 Limits . 14 4.2.6.3 Conformance . 14 4.2.7 Receiver Blocking Characteristics . 14 4.2.7.1 Definition . 14 4.2.7.2 Limits . 14 4.2.7.3 Conformance . 16 4.2.8 Receiver Spurious Response . 16 4.2.8.1 Definition . 16 4.2.8.2 Limits . 16 4.2.8.3 Conformance . 17 4.2.9 Receiver Intermodulation Characteristics . 17 4.2.9.1 Definition . 17 4.2.9.2 Limits . 17 4.2.9.3 Conformance . 18 4.2.10 Receiver Spurious Emissions . 18 SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)4 4.2.10.1 Definition . 18 4.2.10.2 Limits . 18 4.2.10.3 Conformance . 18 4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 19 4.2.11.1 Definition . 19 4.2.11.2 Limits . 19 4.2.11.2.1 Requirements for 5 MHz channel bandwidth . 19 4.2.11.2.2 Requirements for 10 MHz channel bandwidth . 19 4.2.11.3 Conformance . 20 5 Testing for compliance with technical requirements . 20 5.1 Environmental conditions for testing . 20 5.2 Product information . 20 5.3 Interpretation of the measurement results . 20 5.4 Essential radio test suites . 21 5.4.1 Transmitter Maximum and Minimum Output Power . 21 5.4.1.1 Method of measurement . 21 5.4.1.1.1 Initial conditions . 22 5.4.1.1.2 Procedure . 22 5.4.1.2 Test requirements . 22 5.4.2 Transmitter Spectrum Emission Mask . 22 5.4.2.1 Method of measurement . 23 5.4.2.1.1 Initial conditions . 23 5.4.2.1.2 Procedure . 23 5.4.2.2 Test requirements . 24 5.4.3 Transmitter spurious emissions . 24 5.4.3.1 Method of measurement . 24 5.4.3.1.1 Initial conditions . 24 5.4.3.1.2 Procedure . 25 5.4.3.2 Test requirements . 25 5.4.4 Receiver Adjacent Channel Selectivity (ACS) . 25 5.4.4.1 Method of measurement . 25 5.4.4.1.1 Initial conditions . 26 5.4.4.1.2 Procedure . 26 5.4.4.2 Test requirements . 26 5.4.5 Receiver Blocking Characteristics . 26 5.4.5.1 Method of measurement . 26 5.4.5.1.1 Initial conditions . 27 5.4.5.1.2 Procedure . 27 5.4.5.2 Test requirements . 28 5.4.6 Receiver Spurious Response . 28 5.4.6.1 Method of measurement . 28 5.4.6.1.1 Initial conditions . 28 5.4.6.1.2 Procedure . 28 5.4.6.2 Test requirements . 29 5.4.7 Receiver Intermodulation characteristics . 29 5.4.7.1 Method of measurement . 29 5.4.7.1.1 Initial conditions . 29 5.4.7.1.2 Procedure . 30 5.4.7.2 Test requirements . 30 5.4.8 Receiver Spurious Emissions . 30 5.4.8.1 Method of measurement . 30 5.4.8.1.1 Initial conditions . 31 5.4.8.1.2 Procedure . 31 5.4.8.2 Test requirements . 31 5.4.9 Transmitter Adjacent Channel Leakage Power Ratio . 31 5.4.9.1 Method of measurement . 31 5.4.9.1.1 Initial conditions . 32 5.4.9.1.2 Procedure . 32 5.4.9.2 Test requirements . 33 SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)5 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 34 Annex B (normative): Environmental profile . 36 Annex C (informative): Void . 37 Annex D (informative): Bibliography . 38 History . 39
SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.8]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonized Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A. The present document is part 19 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
National transposition dates Date of adoption of this EN: 10 June 2013 Date of latest announcement of this EN (doa): 30 September 2013 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 March 2014 Date of withdrawal of any conflicting National Standard (dow): 31 March 2015
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)7 1 Scope The present document applies to the following radio equipment type: • User Equipment for IMT-2000 OFDMA TDD WMAN (Mobile WiMAX) operating in TDD mode. This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: OFDMA TDD WMAN User Equipment frequency bands Mobile WiMAX Band Class Index
IMT-2000 OFDMA TDD WMAN service operating bands Channel Bandwidth 1.B 2 300 MHz to 2 400 MHz 5 MHz and 10 MHz
3.A 2 500 MHz to 2 690 MHz 5 MHz and 10 MHz 5L.A 3 400 MHz to 3 600 MHz 5 MHz 5L.C 3 400 MHz to 3 600 MHz 10 MHz 5H.A 3 600 MHz to 3 800 MHz 5 MHz 5H.C 3 600 MHz to 3 800 MHz 10 MHz
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive 1999/5/EC [i.2] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] ETSI EN 301 908-1 (V6.2.1) (04-2013): "IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements". [2] CEPT/ERC/Recommendation 74-01E (Edition of January, 2011) (Siófok 98, Nice 99, Sesimbra 02, Hradec Kralove 05): "Unwanted emissions in the spurious domain". SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)8 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. [i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the R&TTE Directive". [i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Recommended approach, and possible limits for measurement uncertainty for the measurement of radiated electromagnetic fields above 1 GHz". [i.5] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction". [i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.7] Recommendation ITU-R SM.329-12 (2012): "Unwanted emissions in the spurious domain". [i.8] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the R&TTE Directive 1999/5/EC [i.2] and the following apply: burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which no intentional transmission is made environmental profile: declared range of environmental conditions under which equipment within the scope of the present document is required to be compliant
integral antenna: antenna which is declared to be part of the radio equipment by the manufacturer
NOTE: Even when equipment with an integral antenna is concerned, it might still be possible to separate the antenna from the equipment using a special tool. In such cases the assessment of the radio equipment and of the antenna against requirements of the present document may be done separately. maximum output power: mean power level per carrier of the base station measured at the antenna connector in a specified reference condition mean power: when applied to a modulated signal, this is the power (transmitted or received) in a bandwidth nominal maximum output power: maximum nominal mean power level per carrier of the user equipment available at the antenna connector declared by the manufacturer; for equipment implementing dynamic change of modulation format, it is intended as the maximum nominal mean power associated to the modulation format delivering the highest power receiver thermal noise power: equal to k×T×BW×F SIST EN 301 908-19 V6.2.1:2013
ETSI ETSI EN 301 908-19 V6.2.1 (2013-06)9 WiMAX: trademarked name for the OFDMA TDD WMAN IMT technology 3.2 Symbols For the purposes of the present document, the following symbols apply: ABS Base Station Interface A AMS Mobile Station Interface
...
ETSI EN 301 908-19 V6.2.1 (2013-06)
Harmonized European Standard
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 19: OFDMA TDD WMAN (Mobile WiMAX)
TDD User Equipment (UE)
---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-19 V6.2.1 (2013-06)
Reference
REN/MSG-TFES-010-19
Keywords
IMT, IMT-2000, mobile, OFDMA, radio,
regulation, TDD, WiMAX, WMAN
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2013.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-19 V6.2.1 (2013-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Essential requirements specification . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Introduction. 10
4.2.2 Transmitter Maximum Output Power . 10
4.2.2.1 Definition . 10
4.2.2.2 Limits . 10
4.2.2.3 Conformance . 10
4.2.3 Transmitter Spectrum Emission Mask . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.2.1 Requirements for 5 MHz channel bandwidth . 11
4.2.3.2.2 Requirements for 10 MHz channel bandwidth . 11
4.2.3.3 Conformance . 12
4.2.4 Transmitter Spurious Emissions . 12
4.2.4.1 Definition . 12
4.2.4.2 Limits . 12
4.2.4.2.1 Requirements for 5 MHz channel bandwidth . 12
4.2.4.2.2 Requirements for 10 MHz channel bandwidth . 13
4.2.4.2.3 Requirements for UE Coexistence. 13
4.2.4.3 Conformance . 13
4.2.5 Transmitter Minimum Output Power . 13
4.2.5.1 Definition . 13
4.2.5.2 Limits . 13
4.2.5.3 Conformance . 13
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 14
4.2.6.1 Definition . 14
4.2.6.2 Limits . 14
4.2.6.3 Conformance . 14
4.2.7 Receiver Blocking Characteristics . 14
4.2.7.1 Definition . 14
4.2.7.2 Limits . 14
4.2.7.3 Conformance . 16
4.2.8 Receiver Spurious Response . 16
4.2.8.1 Definition . 16
4.2.8.2 Limits . 16
4.2.8.3 Conformance . 17
4.2.9 Receiver Intermodulation Characteristics . 17
4.2.9.1 Definition . 17
4.2.9.2 Limits . 17
4.2.9.3 Conformance . 18
4.2.10 Receiver Spurious Emissions . 18
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-19 V6.2.1 (2013-06)
4.2.10.1 Definition . 18
4.2.10.2 Limits . 18
4.2.10.3 Conformance . 18
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 19
4.2.11.1 Definition . 19
4.2.11.2 Limits . 19
4.2.11.2.1 Requirements for 5 MHz channel bandwidth . 19
4.2.11.2.2 Requirements for 10 MHz channel bandwidth . 19
4.2.11.3 Conformance . 20
5 Testing for compliance with technical requirements . 20
5.1 Environmental conditions for testing . 20
5.2 Product information . 20
5.3 Interpretation of the measurement results . 20
5.4 Essential radio test suites . 21
5.4.1 Transmitter Maximum and Minimum Output Power . 21
5.4.1.1 Method of measurement . 21
5.4.1.1.1 Initial conditions . 22
5.4.1.1.2 Procedure . 22
5.4.1.2 Test requirements . 22
5.4.2 Transmitter Spectrum Emission Mask . 22
5.4.2.1 Method of measurement . 23
5.4.2.1.1 Initial conditions . 23
5.4.2.1.2 Procedure . 23
5.4.2.2 Test requirements . 24
5.4.3 Transmitter spurious emis sions . 24
5.4.3.1 Method of measurement . 24
5.4.3.1.1 Initial conditions . 24
5.4.3.1.2 Procedure . 25
5.4.3.2 Test requirements . 25
5.4.4 Receiver Adjacent Channel Selectivity (ACS) . 25
5.4.4.1 Method of measurement . 25
5.4.4.1.1 Initial conditions . 26
5.4.4.1.2 Procedure . 26
5.4.4.2 Test requirements . 26
5.4.5 Receiver Blocking Characteristics . 26
5.4.5.1 Method of measurement . 26
5.4.5.1.1 Initial conditions . 27
5.4.5.1.2 Procedure . 27
5.4.5.2 Test requirements . 28
5.4.6 Receiver Spurious Response . 28
5.4.6.1 Method of measurement . 28
5.4.6.1.1 Initial conditions . 28
5.4.6.1.2 Procedure . 28
5.4.6.2 Test requirements . 29
5.4.7 Receiver Intermodulation characteristics . 29
5.4.7.1 Method of measurement . 29
5.4.7.1.1 Initial conditions . 29
5.4.7.1.2 Procedure . 30
5.4.7.2 Test requirements . 30
5.4.8 Receiver Spurious Emissions . 30
5.4.8.1 Method of measurement . 30
5.4.8.1.1 Initial conditions . 31
5.4.8.1.2 Procedure . 31
5.4.8.2 Test requirements . 31
5.4.9 Transmitter Adjacent Channel Leakage Power Ratio . 31
5.4.9.1 Method of measurement . 31
5.4.9.1.1 Initial conditions . 32
5.4.9.1.2 Procedure . 32
5.4.9.2 Test requirements . 33
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-19 V6.2.1 (2013-06)
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 34
Annex B (normative): Environmental profile . 36
Annex C (informative): Void . 37
Annex D (informative): Bibliography . 38
History . 39
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-19 V6.2.1 (2013-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group
(MSG).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.8].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2].
See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.2] are summarized in annex A.
The present document is part 19 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
National transposition dates
Date of adoption of this EN: 10 June 2013
Date of latest announcement of this EN (doa): 30 September 2013
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2014
Date of withdrawal of any conflicting National Standard (dow): 31 March 2015
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-19 V6.2.1 (2013-06)
1 Scope
The present document applies to the following radio equipment type:
• User Equipment for IMT-2000 OFDMA TDD WMAN (Mobile WiMAX) operating in TDD mode.
This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1.
Table 1-1: OFDMA TDD WMAN User Equipment frequency bands
Mobile WiMAX Band Class IMT-2000 OFDMA TDD WMAN service Channel Bandwidth
Index operating bands
1.B 2 300 MHz to 2 400 MHz 5 MHz and 10 MHz
3.A 2 500 MHz to 2 690 MHz 5 MHz and 10 MHz
5L.A 3 400 MHz to 3 600 MHz 5 MHz
5L.C 3 400 MHz to 3 600 MHz 10 MHz
5H.A 3 600 MHz to 3 800 MHz 5 MHz
5H.C 3 600 MHz to 3 800 MHz 10 MHz
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2,
which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive 1999/5/EC [i.2] may apply to equipment within the scope of the
present document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 908-1 (V6.2.1) (04-2013): "IMT cellular networks; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common
requirements".
[2] CEPT/ERC/Recommendation 74-01E (Edition of January, 2011) (Siófok 98, Nice 99,
Sesimbra 02, Hradec Kralove 05): "Unwanted emissions in the spurious domain".
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-19 V6.2.1 (2013-06)
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of Harmonized Standards for application under the R&TTE Directive".
[i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
[i.5] ETSI EN 300 019-1-0: "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-0: Classification of environmental
conditions; Introduction".
[i.6] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[i.7] Recommendation ITU-R SM.329-12 (2012): "Unwanted emissions in the spurious domain".
[i.8] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending
Directive 98/34/EC laying down a procedure for the provision of information in the field of
technical standards and regulations.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in the R&TTE Directive 1999/5/EC [i.2] and
the following apply:
burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which
no intentional transmission is made
environmental profile: declared range of environmental conditions under which equipment within the scope of the
present document is required to be compliant
integral antenna: antenna which is declared to be part of the radio equipment by the manufacturer
NOTE: Even when equipment with an integral antenna is concerned, it might still be possible to separate the
antenna from the equipment using a special tool. In such cases the assessment of the radio equipment and
of the antenna against requirements of the present document may be done separately.
maximum output power: mean power level per carrier of the base station measured at the antenna connector in a
specified reference condition
mean power: when applied to a modulated signal, this is the power (transmitted or received) in a bandwidth
nominal maximum output power: maximum nominal mean power level per carrier of the user equipment available at
the antenna connector declared by the manufacturer; for equipment implementing dynamic change of modulation
format, it is intended as the maximum nominal mean power associated to the modulation format delivering the highest
power
receiver thermal noise power: equal to k×T×BW×F
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 301 908-19 V6.2.1 (2013-06)
WiMAX: trademarked name for the OFDMA TDD WMAN IMT technology
3.2 Symbols
For the purposes of the present document, the following symbols apply:
A Base Station Interface A
BS
A Mobile Station Interface A
MS
A Unit Under Test Interface A
UUT
BW Assigned channel bandwidth
dB Decibel
dBc Decibel relative to carri
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.