SIST EN ISO 3923-1:2010
(Main)Metallic powders - Determination of apparent density - Part 1: Funnel method (ISO 3923-1:2008)
Metallic powders - Determination of apparent density - Part 1: Funnel method (ISO 3923-1:2008)
This part of ISO 3923 specifies the funnel method for the determination of the apparent density of metallic powders under standardized conditions. The method is intended for metallic powders that flow freely through a 2,5 mm diameter orifice. It may, however, be used for powders that flow with difficulty through a 2,5 mm diameter orifice but flow through a 5 mm diameter orifice. Methods for the determination of the apparent density of powders that will not flow through a 5 mm diameter orifice are specified in ISO 3923-2.
Metallpulver - Ermittlung der Fülldichte - Teil 1: Trichterverfahren (ISO 3923-1:2008)
Dieser Teil von ISO 3923 legt das Trichterverfahren zur Ermittlung der Fülldichte von Metallpulvern unter
festgelegten Bedingungen fest.
Das Verfahren gilt für Metallpulver, die frei durch eine 2,5 mm-Ausfluss-Öffnung fließen. Es darf jedoch auch
bei Pulvern angewendet werden, die schlecht durch eine 2,5 mm-Ausfluss-Öffnung aber frei durch eine 5 mm-
Ausfluss-Öffnung fließen.
Verfahren zur Ermittlung der Fülldichte von Pulvern, die nicht durch eine 5 mm-Ausfluss-Öffnung fließen, sind
in ISO 3923-2 festgelegt.
Poudres métalliques - Détermination de la masse volumique apparente - Partie 1: Méthode de l'entonnoir (ISO 3923-1:2008)
L'ISO 3923-1:2008 spécifie une méthode dite de l'entonnoir pour déterminer la masse volumique apparente des poudres métalliques dans des conditions normalisées.
Cette méthode est applicable aux poudres métalliques qui s'écoulent librement au travers d'un orifice de 2,5 mm. Elle peut toutefois être utilisée pour des poudres qui s'écoulent avec difficulté au travers d'un orifice de 2,5 mm mais librement au travers d'un orifice de 5 mm.
Des méthodes de détermination de la masse volumique apparente des poudres métalliques qui ne s'écoulent pas au travers d'un orifice de 5 mm sont spécifiées dans l'ISO 3923-2.
Kovinski praški - Ugotavljanje navidezne gostote - 1. del: Preskus z lijakom (ISO 3923-1:2008)
Ta del ISO 3923 določa metodo z lijakom za določanje navidezne gostote kovinskih praškov pod standardiziranimi pogoji. Metoda je namenjena za kovinske praške, ki prosto tečejo skozi odprtine premera 2,5 mm. Vendar se lahko uporabi tudi za praške, ki s težavo tečejo skozi odprtino premera 2,5 mm, ampak tečejo skozi odprtino premera 5 mm. Metode za določanje navidezne gostote praškov, ki ne morejo teči skozi odprtino premera 5 mm, so določene v ISO 3923-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 3923-1:2010
01-julij-2010
1DGRPHãþD
SIST EN 23923-1:2000
Kovinski praški - Ugotavljanje navidezne gostote - 1. del: Preskus z lijakom (ISO
3923-1:2008)
Metallic powders - Determination of apparent density - Part 1: Funnel method (ISO 3923-
1:2008)
Metallpulver - Ermittlung der Fülldichte - Teil 1: Trichterverfahren (ISO 3923-1:2008)
Poudres métalliques - Détermination de la masse volumique apparente - Partie 1:
Méthode de l'entonnoir (ISO 3923-1:2008)
Ta slovenski standard je istoveten z: EN ISO 3923-1:2010
ICS:
77.160 Metalurgija prahov Powder metallurgy
SIST EN ISO 3923-1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3923-1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 3923-1:2010
EUROPEAN STANDARD
EN ISO 3923-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2010
ICS 77.160 Supersedes EN 23923-1:1993
English Version
Metallic powders - Determination of apparent density - Part 1:
Funnel method (ISO 3923-1:2008)
Poudres métalliques - Détermination de la masse Metallpulver - Ermittlung der Fülldichte - Teil 1:
volumique apparente - Partie 1: Méthode de l'entonnoir Trichterverfahren (ISO 3923-1:2008)
(ISO 3923-1:2008)
This European Standard was approved by CEN on 16 April 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3923-1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3923-1:2010
EN ISO 3923-1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 3923-1:2010
EN ISO 3923-1:2010 (E)
Foreword
The text of ISO 3923-1:2008 has been prepared by Technical Committee ISO/TC 119 “Powder metallurgy” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 3923-1:2010.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at
the latest by October 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 23923-1:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 3923-1:2008 has been approved by CEN as a EN ISO 3923-1:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 3923-1:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 3923-1:2010
INTERNATIONAL ISO
STANDARD 3923-1
Third edition
2008-05-01
Metallic powders — Determination of
apparent density —
Part 1:
Funnel method
Poudres métalliques — Détermination de la masse volumique
apparente —
Partie 1: Méthode de l'entonnoir
Reference number
ISO 3923-1:2008(E)
©
ISO 2008
---------------------- Page: 7 ----------------------
SIST EN ISO 3923-1:2010
ISO 3923-1:2008(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2008 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 3923-1:2010
ISO 3923-1:2008(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Principle. 1
4 Symbols and designation . 1
5 Apparatus . 2
6 Sample . 4
7 Procedure . 4
8 Expression of results . 5
9 Precision. 5
9.1 Repeatability. 5
9.2 Reproducibility.
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kovinski praški - Ugotavljanje navidezne gostote - 1. del: Preskus z lijakom (ISO 3923-1:2008)Metallpulver - Ermittlung der Fülldichte - Teil 1: Trichterverfahren (ISO 3923-1:2008)Poudres métalliques - Détermination de la masse volumique apparente - Partie 1: Méthode de l'entonnoir (ISO 3923-1:2008)Metallic powders - Determination of apparent density - Part 1: Funnel method (ISO 3923-1:2008)77.160Metalurgija prahovPowder metallurgyICS:Ta slovenski standard je istoveten z:FprEN ISO 3923-1kSIST FprEN ISO 3923-1:2010en,fr,de01-januar-2010kSIST FprEN ISO 3923-1:2010SLOVENSKI
STANDARD
kSIST FprEN ISO 3923-1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 3923-1
October 2009 ICS 77.160 Will supersede EN 23923-1:1993English Version
Metallic powders - Determination of apparent density - Part 1: Funnel method (ISO 3923-1:2008)
Poudres métalliques - Détermination de la masse volumique apparente - Partie 1: Méthode de l'entonnoir (ISO 3923-1:2008)
Metallpulver - Ermittlung der Fülldichte - Teil 1: Trichterverfahren (ISO 3923-1:2008) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/SS M11.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 3923-1:2009: EkSIST FprEN ISO 3923-1:2010
FprEN ISO 3923-1:2009 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 3923-1:2010
FprEN ISO 3923-1:2009 (E) 3 Foreword The text of ISO 3923-1:2008 has been prepared by Technical Committee ISO/TC 119 “Powder metallurgy” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 3923-1:2009. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 23923-1:1993. Endorsement notice The text of ISO 3923-1:2008 has been approved by CEN as a FprEN ISO 3923-1:2009 without any modification.
kSIST FprEN ISO 3923-1:2010
kSIST FprEN ISO 3923-1:2010
Reference numberISO 3923-1:2008(E)© ISO 2008
INTERNATIONAL STANDARD ISO3923-1Third edition2008-05-01Metallic powders — Determination of apparent density — Part 1: Funnel method Poudres métalliques — Détermination de la masse volumique apparente — Partie 1: Méthode de l'entonnoir
kSIST FprEN ISO 3923-1:2010
ISO 3923-1:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
©
ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2008 – All rights reserved
kSIST FprEN ISO 3923-1:2010
ISO 3923-1:2008(E) © ISO 2008 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Principle.1 4 Symbols and designation.1 5 Apparatus.2 6 Sample.4 7 Procedure.4 8 Expression of results.5 9 Precision.5 9.1 Repeatability.5 9.2 Reproducibility.5 10 Test report.5
kSIST FprEN ISO 3923-1:2010
ISO 3923-1:2008(E) iv © ISO 2008 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.