iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60534-2-2:1998

(Main)

Industrial-process control valves -- Part 2: Flow capacity -- Section 2: Sizing equations for compressible fluid flow under installed conditions

Industrial-process control valves -- Part 2: Flow capacity -- Section 2: Sizing equations for compressible fluid flow under installed conditions

Superseded by EN 60534-2-1:1998

Stellventile für die Prozeßregelung -- Teil 2: Durchflußkapazität -- Hauptabschnitt 2: Bemessungsgleichungen für kompressible Fluide unter Einbaubedingungen

Vannes de régulation des processus industriels -- Partie 2: Capacité d'écoulement -- Section 2: Equations de dimensionnement pour l'écoulement des fluides compressibles dans les conditions d'installation

Industrial-process control valves - Part 2: Flow capacity - Section 2: Sizing equations for compressible fluid flow under installed conditions (IEC 60534-2-2:1980)

General Information

Status
Withdrawn
Publication Date
31-Oct-1998
Withdrawal Date
19-May-2009
ICS
23.060.40 - Pressure regulators
25.040.40 - Industrial process measurement and control
Technical Committee
MKP - Industrial-process measurement and control
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
21-Apr-2009
Due Date
14-May-2009
Completion Date
20-May-2009
Ref Project
EN 60534-2-2:1993 - Industrial-process control valves - Part 2: Flow capacity - Section 2: Sizing equations for compressible fluid flow under installed conditions

Relations

Replaced By
SIST EN 60534-2-1:2001 - Industrial-process control valves -- Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions
Effective Date
29-Jan-2023
Replaced By
SIST EN 60534-2-1:2001 - Industrial-process control valves -- Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions
Effective Date
07-Jun-2022

Buy Standard

EN 60534-2-2:1998EN 60534-2-2:1998
PreviousNext
Standard
EN 60534-2-2:1998
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 60534-1:2007(Main)
Industrial-process control valves -- Part 1: Control valve terminology and general considerations
EN 60534-1:2005

This part of IEC 60534 applies to all types of industrial-process control valves (hereinafter referred to as control valves). This part establishes a partial basic terminology list and provides guidance on the use of all other parts of IEC 60534.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-8-1:2007(Main)
Industrial-process control valves -- Part 8-1: Noise considerations - Laboratory measurement of noise generated by aerodynamic flow through control valves
EN 60534-8-1:2005

This part of IEC 60534-8 defines equipment, methods, and procedures for obtaining laboratory measurements of sound pressure levels radiated by control valves and/or associated piping configurations, including fixed restrictions, through which compressible fluids are passing. Control valves discharging to atmosphere are excluded from this standard. Method A is a uniform method of measuring the radiated noise from the valve and associated test piping and allows a comparison of various measuring results which is beneficial for both user and manufacturer. The noise criteria are expressed by determining the sound pressure level of the valve under consideration. Method B is a procedure for measuring the sound pressure levels within pipe systems upstream and downstream of the valve under fixed operating conditions. Since inaccuracies due to the pipe transmission are eliminated, this method is preferred for evaluation of the acoustical characteristic of valves. The noise characteristics to be determined are useful for the following reasons: a) to compare the performance of different valves; b) to plan measures for noise abatement; c) to determine acoustical characteristics of valves and valve assemblies; d) to enable proper sizing of sound absorbers; e) to determine possible adverse effects on ultra-sonic flow meter measurements.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-4:2007(Main)
Industrial-process control valves -- Part 4: Inspection and routine testing
EN 60534-4:2006

This part of IEC 60534 specifies the requirements for the inspection and routine testing of control valves manufactured in conformity with the other parts of IEC 60534. This standard is applicable to valves with pressure ratings not exceeding Class 2500. The requirements for actuators apply only to pneumatic actuators. This standard does not apply to the types of control valves where radioactive service, fire safety testing, or other hazardous service conditions are encountered. If a standard for hazardous service conflicts with the requirements of this standard, the standard for hazardous service should take precedence.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-5:2004(Main)
Industrial-process control valves -- Part 5: Marking
EN 60534-5:2004

specifies mandatory and supplementary markings of control valves. Some mandatory markings may be inappropriate for some valves of special design, and some supplementary markings may be appropriate only to specific types of control valves. It is recommended that the marking of all valves conform to this standard whenever possible unless otherwise agreed between the manufacturer and purchaser.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-2-5:2004(Main)
Industrial-process control valves -- Part 2-5: Flow capacity - Sizing equations for fluid flow through multistage control valves with interstage recovery
EN 60534-2-5:2003

Gives equations for predicting the flow of compressible and incompressible fluids through multistage control valves. Is based on standard hydrodynamic equations for Newtonian incompressible fluids. Is applicable only to those designs of multistage multipath control valves and multistage single path control valves.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61514:2002(Main)
Industrial-process control systems - Methods of evaluating the performance of valve positioners with pneumatic outputs
EN 61514:2002

IEC 61514:2000 specifies tests designed to determine the static and dynamic performance of single-acting or double-acting valve positioners. The tests may be applied to positioners which receive standard analogue input signals (as specified in IEC 60381 and IEC 60382) and have a pneumatic output.
NOTE For positioners with pulsed or digital input signals, equivalent criteria may be applied. The methods described may not fully apply to positioners with digital controllers or positioners with pulsed outputs.
Testing may be conducted either on a positioner alone, independently of an actuator, or on a positioner mounted and connected to a specific actuator, as a combined unit. The text makes clear where different approaches are required. The methods of evaluation given in this standard are intended for use by manufacturers to determine the performance of their products, and by users, or independent testing establishments, to verify manufacturers' performance specifications. This publication is to be read in conjunction with IEC 61514-2:2013.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-3-2:2002(Main)
Industrial-process control valves -- Part 3-2: Dimensions - Face-to-face dimensions for rotary control valves except butterfly valves
EN 60534-3-2:2001

Gives the overall lengths of following types: segmental ball, eccentric rotary plug, and barstock globe; wafer butterfly valves are excluded.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-6-2:2002(Main)
Industrial-process control valves -- Part 6-2: Mounting details for attachment of positioners to control valves - Positioner mounting on rotary actuators
EN 60534-6-2:2001

Intended to permit a variety of positioning devices, which respond to a rotary motion, to be mounted on the actuator of a control valve, either directly or by employing an intermediate mounting bracket.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-3-3:2000(Main)
Industrial-process control valves -- Part 3-3: Dimensions - End-to-end dimensions for buttweld, two-way, globe-type, straight pattern control valves
EN 60534-3-3:1998

Specifies end-to-end dimensions for given nominal sizes and pressure ratings of buttweld, two-way, global-type, straigth pattern control valves for nominal sizes DN 15 through DN 450. Aids users in their piping design by providing normalized dimensions of buttweld end control valves.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60534-6-1:1998(Main)
Industrial-process control valves -- Part 6: Mounting details for attachment of positioners to control valves -- Section 1: Positioner mounting on linear actuators
EN 60534-6-1:1997

Intended to permit a variety of positioning devices, which respond to a linear motion, to be mounted on the actuator of a control valve, either directly or by employing an intermediate mounting bracket. Applicable where interchangeability between actuators and positioners is desired.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day