SIST EN IEC 61169-67:2022

Radio frequency connectors - Part 67: Sectional specification for series TRL threaded triaxial connectors (IEC 61169-67:2022)

This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for series TRL threaded triaxial connectors. Series TRL threaded triaxial connectors with high reliability, small size, good salt characteristics can be connected with symmetrically twisted pair cables or triaxial cables. It has been used in 1553B data bus systems or other communication systems for digital signal transmission.
It prescribes mating face dimensions for series TRL threaded triaxial connectors, gauging information and tests selected from IEC 61169-1, applicable to all detail specifications relating to series TRL threaded triaxial connectors.
This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H.
Note: Metric dimensions are original dimensions. All undimensioned pictorial configurations are for reference purpose only.

Hochfrequenz-Steckverbinder - Teil 67: Teilspezifikation für triaxiale Steckverbinder mit Gewinde der Serie TRL (IEC 61169-67:2022)

Connecteurs pour fréquences radioélectriques - Partie 67: Spécification intermédiaire relative aux connecteurs triaxiaux filetés de série TRL (IEC 61169-67:2022)

IEC 61169-67:2022, qui est une spécification intermédiaire (SI), fournit des informations et des règles relatives à l’établissement des spécifications particulières (SP) pour les connecteurs triaxiaux filetés de série TRL. Les connecteurs triaxiaux filetés de série TRL, très fiables, de petite taille et présentant de bonnes caractéristiques salines peuvent être connectés à l’aide de câbles triaxiaux ou de câbles à paires torsadées symétriques. Cette spécification a été utilisée dans des systèmes de bus de données 1553B ou d’autres systèmes de communication pour la transmission de signaux numériques.
Elle spécifie les dimensions de la face d’accouplement pour les connecteurs triaxiaux filetés de série TRL, les informations de calibres et les essais choisis à partir de l’IEC 61169-1, applicables à toutes les spécifications particulières relatives aux connecteurs triaxiaux filetés de série TRL.
Cette spécification indique les caractéristiques de performance recommandées à prendre en considération lors de la rédaction d’une spécification particulière et couvre les programmes d’essais et les exigences de contrôle pour les niveaux d’assurance M et H.

Radiofrekvenčni konektorji - 67. del: Področna specifikacija za navojne triaksialne priključke serije TRL (IEC 61169-67:2022)

Ta del standarda IEC 61169, ki je področna specifikacija (SS), podaja informacije in določa pravila za pripravo podrobnih specifikacij (DS) za navojne triaksialne priključke serije TRL. Triaksialni priključki serije TRL z visoko zanesljivostjo, majhnostjo, dobrimi lastnostmi v slanem okolju se lahko povežejo s simetričnimi paricami ali triaksialnimi kabli. Uporablja se v sistemih podatkovnih vodil 1553B ali drugih komunikacijskih sistemih za digitalni prenos signala.
Predpisuje mere spojne površine za navojne triaksialne priključke serije TRL, informacije o merjenju in preskuse, izbrane iz standarda IEC 61169-1, ki se uporabljajo za vse podrobne specifikacije v zvezi z navojnimi triaksialnimi priključki serije TRL.
Ta specifikacija določa priporočene lastnosti, ki jih je treba upoštevati pri sestavljanju podrobne specifikacije, ter zajema urnike preskusov in zahteve za pregled za ravni vrednotenja M in H.
Opomba: Izvirne mere so podane v metričnih enotah. Vse nedimenzionirane slikovne konfiguracije so podane samo v referenčne namene.

General Information

• Status: Published
• Publication Date: 13-Apr-2022
• ICS: 33.120.30 - RF connectors
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 08-Apr-2022
• Due Date: 13-Jun-2022
• Completion Date: 14-Apr-2022
• Ref Project: EN IEC 61169-67:2022 - Radio frequency connectors - Part 67: Sectional specification for series TRL threaded triaxial connectors

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 61169-67:2022
01-junij-2022
Radiofrekvenčni konektorji - 67. del: Področna specifikacija za navojne triaksialne
priključke serije TRL (IEC 61169-67:2022)
Radio frequency connectors - Part 67: Sectional specification for series TRL threaded
triaxial connectors (IEC 61169-67:2022)
Hochfrequenz-Steckverbinder - Teil 67: Teilspezifikation für triaxiale Steckverbinder mit
Gewinde der Serie TRL (IEC 61169-67:2022)
Connecteurs pour fréquences radioélectriques - Partie 67: Spécification intermédiaire
relative aux connecteurs triaxiaux filetés de série TRL (IEC 61169-67:2022)
Ta slovenski standard je istoveten z: EN IEC 61169-67:2022
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
SIST EN IEC 61169-67:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 61169-67:2022

---------------------- Page: 2 ----------------------
SIST EN IEC 61169-67:2022


EUROPEAN STANDARD EN IEC 61169-67

NORME EUROPÉENNE

EUROPÄISCHE NORM April 2022
ICS 33.120.30

English Version
Radio frequency connectors - Part 67: Sectional specification for
series TRL threaded triaxial connectors
(IEC 61169-67:2022)
Connecteurs pour fréquences radioélectriques - Partie 67: Hochfrequenz-Steckverbinder - Teil 67:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für triaxiale Steckverbinder mit
triaxiaux filetés de série TRL Gewinde der Serie TRL
(IEC 61169-67:2022) (IEC 61169-67:2022)
This European Standard was approved by CENELEC on 2022-03-25. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 61169-67:2022 E

---------------------- Page: 3 ----------------------
SIST EN IEC 61169-67:2022
EN IEC 61169-67:2022 (E)
European foreword
The text of document 46F/599/FDIS, future edition 1 of IEC 61169-67, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-67:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-12-25
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-03-25
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61169-67:2022 was approved by CENELEC as a European
Standard without any modification.
2

---------------------- Page: 4 ----------------------
SIST EN IEC 61169-67:2022
EN IEC 61169-67:2022 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General
requirements and measuring methods
IEC 61169-1-5 - Radio frequency connectors - Part 1-5: EN IEC 61169-1-5 -
Electrical test methods - Rise time
degradation


3

---------------------- Page: 5 ----------------------
SIST EN IEC 61169-67:2022

---------------------- Page: 6 ----------------------
SIST EN IEC 61169-67:2022



IEC 61169-67

®


Edition 1.0 2022-02




INTERNATIONAL



STANDARD




NORME


INTERNATIONALE











Radio-frequency connectors –

Part 67: Sectional specification for series TRL threaded triaxial connectors



Connecteurs pour fréquences radioélectriques –

Partie 67: Spécification intermédiaire relative aux connecteurs triaxiaux filetés

de série TRL















INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE


INTERNATIONALE




ICS 33.120.30 ISBN 978-2-8322-1079-7




Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------
SIST EN IEC 61169-67:2022
– 2 – IEC 61169-67:2022 © IEC 2022
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Mating face and gauge information . 6
4.1 Mating face dimensions . 6
4.1.1 Plug connector . 6
4.1.2 Receptacle connector . 7
4.1.3 Coaxial pin contact . 7
4.1.4 Coaxial socket contact . 8
4.2 Gauges for resilient contact . 9
4.2.1 Gauge for socket centre contact . 9
4.2.2 Gauge for socket intermediate contact . 9
5 Quality assessment procedure . 10
5.1 General . 10
5.2 Ratings and characteristics . 10
5.3 Test schedule and inspection requirements. 13
5.3.1 Acceptance tests . 13
5.3.2 Periodic tests . 14
5.3.3 Procedures . 15
6 Instructions for preparation of detail specifications (DS) . 15
6.1 General . 15
6.2 Identification of the component . 16
6.3 Performance . 16
6.4 Marking, ordering information and related matters . 16
6.5 Selection of tests, test conditions and severities . 16
6.6 Blank detail specification pro-forma for TRL connectors . 17

Figure 1 – Plug connector . 6
Figure 2 – Receptacle connector . 7
Figure 3 – Coaxial pin contact . 8
Figure 4 – Coaxial socket contact . 8
Figure 5 – Gauge for socket centre contact . 9
Figure 6 – Gauge for socket intermediate contact . 10

Table 1 – Dimensions of plug connector . 6
Table 2 – Dimensions of receptacle connector . 7
Table 3 – Dimensions of coaxial pin contact . 8
Table 4 – Dimensions of coaxial socket contact . 8
Table 5 – Dimensions of gauge for socket centre contact . 9
Table 6 – Dimensions of gauge for socket intermediate contact . 10
Table 7 – Ratings and characteristics . 11
Table 8 – Acceptance tests . 13
Table 9 – Periodic tests . 14

---------------------- Page: 8 ----------------------
SIST EN IEC 61169-67:2022
IEC 61169-67:2022 © IEC 2022 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 67: Sectional specification for
series TRL threaded triaxial connectors

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61169-67 has been prepared by subcommittee 46F: RF and microwave passive
components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF
and microwave passive components and accessories. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
46F/599/FDIS 46F/609/RVD

Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

---------------------- Page: 9 ----------------------
SIST EN IEC 61169-67:2022
– 4 – IEC 61169-67:2022 © IEC 2022
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts of the IEC 61169 series, under the general title Radio frequency connectors
can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 10 ----------------------
SIST EN IEC 61169-67:2022
IEC 61169-67:2022 © IEC 2022 – 5 –
RADIO-FREQUENCY CONNECTORS –

Part 67: Sectional specification for
series TRL threaded triaxial connectors



1 Scope
This part of IEC 61169, which is a sectional specification (SS), provides information and rules
for the preparation of detail specifications (DS) for series TRL threaded triaxial connectors.
Series TRL threaded triaxial connectors with high reliability, small size, good salt characteristics
can be connected with symmetrically twisted pair cables or triaxial cables. It has been used in
1553B data bus systems or other communication systems for digital signal transmission.
It specifies mating face dimensions for series TRL threaded triaxial connectors, gauging
information and tests selected from IEC 61169-1, applicable to all detail specifications relating
to series TRL threaded triaxial connectors.
This specification indicates recommended performance characteristics to be considered when
writing a detail specification and it covers test schedules and inspection requirements for
assessment levels M and H.
NOTE Metric dimensions are original dimensions. All undimensioned pictorial configurations are for reference
purpose only.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61169-1:2013, Radio frequency connectors – Part 1: Generic specification − General
requirements and measuring methods
IEC 61169-1-5, Radio frequency connectors – Part 1-5: Electrical test methods − Rise time
degradation
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61169-1 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
coaxial pin contact
connecting part with a coaxial structure, the outer conductor of which is a pin and the inner
conductor is a socket

---------------------- Page: 11 ----------------------
SIST EN IEC 61169-67:2022
– 6 – IEC 61169-67:2022 © IEC 2022
3.2
coaxial socket contact
connecting part with a coaxial structure, the outer conductor of which is a socket and the inner
conductor is a pin
4 Mating face and gauge information
4.1 Mating face dimensions
4.1.1 Plug connector
The mating face of the plug connector is shown in Figure 1 and its dimensions are shown in
Table 1.

NOTE 1 Slot design of alignment fingers is optional.
NOTE 2 See Figure 3 and Figure 4 for coaxial contact requirements.
NOTE 3 Dimensions in fully mated state.
Figure 1 – Plug connector
Table 1 – Dimensions of plug connector
Ref. mm
Min. Max.
a 5,00 -
b 13° 21°
c - 5,10
d 6,30 8,25
e 6,20 7,70
f 10,00 10,60

---------------------- Page: 12 ----------------------
SIST EN IEC 61169-67:2022
IEC 61169-67:2022 © IEC 2022 – 7 –
4.1.2 Receptacle connector
The mating face of the receptacle connector is shown in Figure 2 and its dimensions are shown
in Table 2.

NOTE See Figure 3 and Figure 4 for coaxial contact requirements.
Figure 2 – Receptacle connector
Table 2 – Dimensions of receptacle connector
Ref. mm
Min. Max.
a 0,25 -
b - 0,45
c 14° 22°
d 5,33 5,56
e 6,04 6,12
f 7,70 7,80

4.1.3 Coaxial pin contact
The mating face of the coaxial pin contact is shown in Figure 3 and its dimensions are shown
in Table 3.

---------------------- Page: 13 ----------------------
SIST EN IEC 61169-67:2022
– 8 – IEC 61169-67:2022 © IEC 2022

NOTE Slot design is optional.
Figure 3 – Coaxial pin contact
Table 3 – Dimensions of coaxial pin contact
Ref. mm
Min. Max.
a 7,09 -
b 0,35 -
c 1,82 1,88
d 1,00 1,55

4.1.4 Coaxial socket contact
The mating face of the coaxial socket contact is shown in Figure 4 and its dimensions are shown
in Table 4.

NOTE Slot design is optional.
Figure 4 – Coaxial socket contact
Table 4 – Dimensions of coaxial socket contact
Ref. mm
Min. Max.
a 0,18 0,99
b - 2,70
c 0,58 0,64

---------------------- Page: 14 ----------------------
SIST EN IEC 61169-67:2022
IEC 61169-67:2022 © IEC 2022 – 9 –
4.2 Gauges for resilient contact
4.2.1 Gauge for socket centr
...