Coating powders - Part 2: Determination of density by gas comparison pyknometer (referee method) (ISO 8130-2:2021)

This document specifies a method for the determination of density for all types of coating powders
using a gas comparison pycnometer.

Pulverlacke - Teil 2: Bestimmung der Dichte mit einem Gasvergleichspyknometer (Schiedsverfahren) (ISO 8130-2:2021)

Dieses Dokument legt ein Verfahren zum Bestimmen der Dichte von Pulverlacken mit einem Gasvergleichspyknometer fest.

Poudres pour revêtement - Partie 2: Détermination de la masse volumique à l'aide d'un pycnomètre à gaz (méthode de référence) (ISO 8130-2:2021)

Le présent document spécifie une méthode pour la détermination de la masse volumique pour tous les types de poudres pour revêtement à l'aide d'un pycnomètre à gaz.

Praškasti premazi - 2. del: Določanje gostote s piknometrom za primerjavo plinov (referenčna metoda) (ISO 8130-2:2021)

General Information

Status
Published
Public Enquiry End Date
02-Dec-2020
Publication Date
16-Aug-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
22-Jul-2021
Due Date
26-Sep-2021
Completion Date
17-Aug-2021

Relations

Buy Standard

Standard
EN ISO 8130-2:2021
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 8130-2:2020
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 8130-2:2021
01-september-2021
Nadomešča:
SIST EN ISO 8130-2:2012
Praškasti premazi - 2. del: Določanje gostote s piknometrom za primerjavo plinov
(referenčna metoda) (ISO 8130-2:2021)
Coating powders - Part 2: Determination of density by gas comparison pyknometer
(referee method) (ISO 8130-2:2021)
Pulverlacke - Teil 2: Bestimmung der Dichte mit einem Gasvergleichspyknometer
(Schiedsverfahren) (ISO 8130-2:2021)
Poudres pour revêtement - Partie 2: Détermination de la masse volumique à l'aide d'un
pycnomètre à gaz (méthode de référence) (ISO 8130-2:2021)
Ta slovenski standard je istoveten z: EN ISO 8130-2:2021
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 8130-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 8130-2:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 8130-2:2021


EN ISO 8130-2
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2021
EUROPÄISCHE NORM
ICS 87.040 Supersedes EN ISO 8130-2:2010
English Version

Coating powders - Part 2: Determination of density by gas
comparison pyknometer (referee method) (ISO 8130-
2:2021)
Poudres pour revêtement - Partie 2: Détermination de Pulverlacke - Teil 2: Bestimmung der Dichte mit einem
la masse volumique à l'aide d'un pycnomètre à gaz Gasvergleichspyknometer (Schiedsverfahren) (ISO
(méthode de référence) (ISO 8130-2:2021) 8130-2:2021)
This European Standard was approved by CEN on 28 April 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8130-2:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 8130-2:2021
EN ISO 8130-2:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 8130-2:2021
EN ISO 8130-2:2021 (E)
European foreword
This document (EN ISO 8130-2:2021) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2022, and conflicting national standards shall
be withdrawn at the latest by January 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8130-2:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN websites.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8130-2:2021 has been approved by CEN as EN ISO 8130-2:2021 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 8130-2:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 8130-2:2021
INTERNATIONAL ISO
STANDARD 8130-2
Second edition
2021-06
Coating powders —
Part 2:
Determination of density by gas
comparison pycnometer (referee
method)
Poudres pour revêtement —
Partie 2: Détermination de la masse volumique à l'aide d'un
pycnomètre à gaz (méthode de référence)
Reference number
ISO 8130-2:2021(E)
©
ISO 2021

---------------------- Page: 7 ----------------------
SIST EN ISO 8130-2:2021
ISO 8130-2:2021(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 8130-2:2021
ISO 8130-2:2021(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Materials . 1
6 Apparatus . 1
7 Sampling . 2
8 Procedure. 2
9 Expression of results . 3
10 Precision . 3
11 Test report . 3
Bibliography .
...

SLOVENSKI STANDARD
oSIST prEN ISO 8130-2:2020
01-november-2020
Praškasti premazi - 2. del: Določanje gostote s piknometrom za primerjavo plinov
(referenčna metoda) (ISO/DIS 8130-2:2020)
Coating powders - Part 2: Determination of density by gas comparison pyknometer
(referee method) (ISO/DIS 8130-2:2020)
Pulverlacke - Teil 2: Bestimmung der Dichte mit einem Gasvergleichspyknometer
(Schiedsverfahren) (ISO/DIS 8130-2:2020)
Poudres pour revêtement - Partie 2: Détermination de la masse volumique à l'aide d'un
pycnomètre à gaz (méthode de référence) (ISO/DIS 8130-2:2020)
Ta slovenski standard je istoveten z: prEN ISO 8130-2
ICS:
87.040 Barve in laki Paints and varnishes
oSIST prEN ISO 8130-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 8130-2:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 8130-2:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8130-2
ISO/TC 35/SC 9 Secretariat: BSI
Voting begins on: Voting terminates on:
2020-09-22 2020-12-15
Coating powders —
Part 2:
Determination of density by gas comparison pyknometer
(referee method)
Poudres pour revêtement —
Partie 2: Détermination de la masse volumique à l'aide d'un pycnomètre à gaz (méthode de référence)
ICS: 87.040
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
This document is circulated as received from the committee secretariat.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8130-2:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020

---------------------- Page: 3 ----------------------
oSIST prEN ISO 8130-2:2020
ISO/DIS 8130-2:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 8130-2:2020
ISO/DIS 8130-2:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Materials . 1
6 Apparatus . 1
7 Sampling . 2
8 Procedure. 2
9 Expression of results . 3
10 Precision . 3
11 Test report . 3
Bibliography . 5
© ISO 2020 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 8130-2:2020
ISO/DIS 8130-2:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.