SIST EN 302 017 V2.1.1:2017
(Main)Transmitting equipment for the Amplitude Modulated (AM) sound broadcasting service - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
Transmitting equipment for the Amplitude Modulated (AM) sound broadcasting service - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
The present document specifies technical characteristics and methods of measurements for transmitter equipment for
broadcast sound services using the Double Side Band amplitude modulated sound broadcasting service operating in the
LF, MF and HF bands.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
Oddajniška oprema za amplitudno modulirano (AM) zvokovno radiodifuzijsko storitev - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU
Ta dokument določa tehnične lastnosti in merilne metode za oddajniško opremo za zvokovne radiodifuzijske storitve, ki uporablja amplitudno modulirano zvokovno radiodifuzijsko storitev z dvobočnim prenosom v pasovih LF, MF in HF.
Ta dokument zajema bistvene zahteve člena 3.2 direktive 2014/53/EU [i.1] pod pogoji iz dodatka A.
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.X]LMVNR(8Transmitting equipment for the Amplitude Modulated (AM) sound broadcasting service - Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU33.170Televizijska in radijska difuzijaTelevision and radio broadcasting33.060.20Sprejemna in oddajna opremaReceiving and transmitting equipmentICS:Ta slovenski standard je istoveten z:ETSI EN 302 017 V2.1.1 (2017-04)SIST EN 302 017 V2.1.1:2017en01-junij-2017SIST EN 302 017 V2.1.1:2017SLOVENSKI
STANDARD
SIST EN 302 017 V2.1.1:2017
ETSI EN 302 017 V2.1.1 (2017-04) Transmitting equipment for the Amplitude Modulated (AM) sound broadcasting service; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 302 017 V2.1.1:2017
ETSI ETSI EN 302 017 V2.1.1 (2017-04) 2
Reference REN/ERM-TG17-14 Keywords AM, audio, broadcasting, harmonised standard, radio, regulation, terrestrial, transmitter ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 017 V2.1.1:2017
ETSI ETSI EN 302 017 V2.1.1 (2017-04) 3Contents Intellectual Property Rights . 5 Foreword . 5 Modal verbs terminology . 5 Introduction . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 6 2.2 Informative references . 6 3 Definitions, symbols and abbreviations . 7 3.1 Definitions . 7 3.2 Symbols . 8 3.3 Abbreviations . 8 4 Technical requirements specifications . 8 4.1 Environmental profile . 8 4.2 Conformance requirements . 8 4.2.1 Rated output power . 8 4.2.1.1 Definition . 8 4.2.1.2 Limit . 8 4.2.1.3 Conformance . 8 4.2.2 Frequency drift . 8 4.2.2.1 Definition . 8 4.2.2.2 Limit . 9 4.2.2.3 Conformance . 9 4.2.3 Spurious emissions . 9 4.2.3.1 Definition . 9 4.2.3.2 Limit . 9 4.2.3.3 Conformance . 10 4.2.4 Transmitter muting during frequency shift . 10 4.2.4.1 Definition . 10 4.2.4.2 Limits . 10 4.2.4.3 Conformance . 10 4.2.5 Out-of-band emissions . 10 4.2.5.1 Definition . 10 4.2.5.2 Limit . 10 4.2.5.3 Conformance . 12 5 Testing for compliance with technical requirements . 12 5.1 Environmental conditions for testing . 12 5.2 Interpretation of the measurement results . 12 5.3 Methods of measurement . 13 5.3.1 Rated output power . 13 5.3.1.1 Initial conditions . 13 5.3.1.2 Procedure . 13 5.3.1.3 Test requirements . 13 5.3.2 Frequency drift . 14 5.3.2.1 Initial conditions . 14 5.3.2.2 Procedure . 14 5.3.2.3 Test requirements . 14 5.3.3 Spurious emissions . 14 5.3.3.1 Initial conditions . 14 5.3.3.2 Procedure . 14 5.3.3.3 Test requirements . 15 5.3.4 Transmitter muting during frequency shift . 15 5.3.4.1 Initial conditions . 15 SIST EN 302 017 V2.1.1:2017
ETSI ETSI EN 302 017 V2.1.1 (2017-04) 45.3.4.2 Procedure . 15 5.3.4.3 Test requirements . 15 5.3.5 Out-of-band emissions . 15 5.3.5.1 Initial conditions . 15 5.3.5.2 Procedure . 16 5.3.5.3 Test requirements . 16 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 17 Annex B (normative): General measuring arrangements . 18 B.1 Testing arrangements for antenna port measurements . 18 B.2 Test frequency range . 18 B.3 Test modulating signal . 19 B.4 Test load characteristics . 20 Annex C (informative): Change History . 21 History . 22
SIST EN 302 017 V2.1.1:2017
ETSI ETSI EN 302 017 V2.1.1 (2017-04) 5Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.1]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations.
National transposition dates Date of adoption of this EN: 27 March 2017 Date of latest announcement of this EN (doa): 30 June 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 December 2017 Date of withdrawal of any conflicting National Standard (dow): 31 December 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document describes the requirements for the design and operation of an AM sound broadcasting service transmitter to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1]. SIST EN 302 017 V2.1.1:2017
ETSI ETSI EN 302 017 V2.1.1 (2017-04) 61 Scope The present document specifies technical characteristics and methods of measurements for transmitter equipment for broadcast sound services using the Double Side Band amplitude modulated sound broadcasting service operating in the LF, MF and HF bands. The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the conditions identified in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at https://docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. Not applicable. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. [i.2] ETSI TR 100 028-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 1". [i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2". [i.4] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. SIST EN 302 017 V2.1.1:2017
ETSI ETSI EN 302 017 V2.1.1 (2017-04) 73 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the following apply: antenna port: port of an apparatus which is designed, in normal operation, to be connected to an antenna using coaxial cable broadcasting service: radiocommunication service in which the transmissions are intended for direct reception by the general public NOTE: This service may include sound transmissions, television transmissions or other types of transmission. carrier power: average power supplied to the antenna transmission line by a transmitter during one cycle taken under the condition of no modulation channel bandwidth: frequency band of defined width (as a multiple of the carrier grid) including safety margin for operation on adjacent channels, located symmetrically around a carrier frequency in the carrier grid class of emission: set of characteristics of an emission, designated by standard symbols, e.g. type of modulation of the main carrier, modulating signal, type of information to be transmitted, and also, if appropriate, any additional signal characteristics dBc: decibels relative to the unmodulated carrier power of the emission NOTE: In the cases which do not have a carrier, for example in some digital modulation schemes where the carrier is not accessible for measurement, the reference level equivalent to dBc is decibels relative to the mean power P. enclosure port: physical boundary of the apparatus through which electromagnetic fields may radiate or impinge NOTE: In the case of integral antenna equipment, this port is inseparable from the antenna port. harmonic: component of order greater than 1 of the Fourier series of a periodic quantity harmoni
...
ETSI EN 302 017 V2.1.1 (2017-04)
HARMONISED EUROPEAN STANDARD
Transmitting equipment for the
Amplitude Modulated (AM) sound broadcasting service;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 302 017 V2.1.1 (2017-04)
Reference
REN/ERM-TG17-14
Keywords
AM, audio, broadcasting, harmonised standard,
radio, regulation, terrestrial, transmitter
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 017 V2.1.1 (2017-04)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Rated output power . 8
4.2.1.1 Definition . 8
4.2.1.2 Limit . 8
4.2.1.3 Conformance . 8
4.2.2 Frequency drift . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 9
4.2.2.3 Conformance . 9
4.2.3 Spurious emissions . 9
4.2.3.1 Definition . 9
4.2.3.2 Limit . 9
4.2.3.3 Conformance . 10
4.2.4 Transmitter muting during frequency shift . 10
4.2.4.1 Definition . 10
4.2.4.2 Limits . 10
4.2.4.3 Conformance . 10
4.2.5 Out-of-band emissions . 10
4.2.5.1 Definition . 10
4.2.5.2 Limit . 10
4.2.5.3 Conformance . 12
5 Testing for compliance with technical requirements . 12
5.1 Environmental conditions for testing . 12
5.2 Interpretation of the measurement results . 12
5.3 Methods of measurement . 13
5.3.1 Rated output power . 13
5.3.1.1 Initial conditions . 13
5.3.1.2 Procedure . 13
5.3.1.3 Test requirements . 13
5.3.2 Frequency drift . 14
5.3.2.1 Initial conditions . 14
5.3.2.2 Procedure . 14
5.3.2.3 Test requirements . 14
5.3.3 Spurious emissions . 14
5.3.3.1 Initial conditions . 14
5.3.3.2 Procedure . 14
5.3.3.3 Test requirements . 15
5.3.4 Transmitter muting during frequency shift . 15
5.3.4.1 Initial conditions . 15
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 017 V2.1.1 (2017-04)
5.3.4.2 Procedure . 15
5.3.4.3 Test requirements . 15
5.3.5 Out-of-band emissions . 15
5.3.5.1 Initial conditions . 15
5.3.5.2 Procedure . 16
5.3.5.3 Test requirements . 16
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 17
Annex B (normative): General measuring arrangements . 18
B.1 Testing arrangements for antenna port measurements . 18
B.2 Test frequency range . 18
B.3 Test modulating signal . 19
B.4 Test load characteristics . 20
Annex C (informative): Change History . 21
History . 22
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 017 V2.1.1 (2017-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 27 March 2017
Date of latest announcement of this EN (doa): 30 June 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2017
Date of withdrawal of any conflicting National Standard (dow): 31 December 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document describes the requirements for the design and operation of an AM sound broadcasting service
transmitter to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1].
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 017 V2.1.1 (2017-04)
1 Scope
The present document specifies technical characteristics and methods of measurements for transmitter equipment for
broadcast sound services using the Double Side Band amplitude modulated sound broadcasting service operating in the
LF, MF and HF bands.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 1".
[i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.4] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 017 V2.1.1 (2017-04)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the
following apply:
antenna port: port of an apparatus which is designed, in normal operation, to be connected to an antenna using coaxial
cable
broadcasting service: radiocommunication service in which the transmissions are intended for direct reception by the
general public
NOTE: This service may include sound transmissions, television transmissions or other types of transmission.
carrier power: average power supplied to the antenna transmission line by a transmitter during one cycle taken under
the condition of no modulation
channel bandwidth: frequency band of defined width (as a multiple of the carrier grid) including safety margin for
operation on adjacent channels, located symmetrically around a carrier frequency in the carrier grid
class of emission: set of characteristics of an emission, designated by standard symbols, e.g. type of modulation of the
main carrier, modulating signal, type of information to be transmitted, and also, if appropriate, any additional signal
characteristics
dBc: decibels relative to the unmodulated carrier power of the emission
NOTE: In the cases which do not have a carrier, for example in some digital modulation schemes where the
carrier is not accessible for measurement, the reference level equivalent to dBc is decibels relative to the
mean power P.
enclosure port: physical boundary of the apparatus through which electromagnetic fields may radiate or impinge
NOTE: In the case of integral antenna equipment, this port is inseparable from the antenna port.
harmonic: component of order greater than 1 of the Fourier series of a periodic quantity
harmonic number: integral number given by the ratio of the frequency of a harmonic to the fundamental frequency
(second harmonic = 2 × fundamental frequency)
intermodulation products: unwanted frequencies resulting from intermodulation between carriers or harmonics of
emission, or between any oscillations generated to produce the carrier
mean power: average power supplied to the antenna transmission line by a transmitter during an interval of time
sufficiently long compared with the lowest frequency encountered in the modulation envelope taken under normal
operating conditions
...
Draft ETSI EN 302 017 V2.0.3 (2016-12)
HARMONISED EUROPEAN STANDARD
Transmitting equipment for the
Amplitude Modulated (AM) sound broadcasting service;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 017 V2.0.3 (2016-12)
Reference
REN/ERM-TG17-14
Keywords
AM, audio, broadcasting, harmonised standard,
radio, regulation, terrestrial, transmitter
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 017 V2.0.3 (2016-12)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions, symbols and abbreviations . 7
3.1 Definitions . 7
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Technical requirements specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Rated output power . 8
4.2.1.1 Definition . 8
4.2.1.2 Limit . 8
4.2.1.3 Conformance . 8
4.2.2 Frequency drift . 8
4.2.2.1 Definition . 8
4.2.2.2 Limit . 9
4.2.2.3 Conformance . 9
4.2.3 Spurious emissions . 9
4.2.3.1 Definition . 9
4.2.3.2 Limit . 9
4.2.3.3 Conformance . 10
4.2.4 Transmitter muting during frequency shift . 10
4.2.4.1 Definition . 10
4.2.4.2 Limits . 10
4.2.4.3 Conformance . 10
4.2.5 Out-of-band emissions . 10
4.2.5.1 Definition . 10
4.2.5.2 Limit . 10
4.2.5.3 Conformance . 12
5 Testing for compliance with technical requirements . 12
5.1 Environmental conditions for testing . 12
5.2 Interpretation of the measurement results . 12
5.3 Methods of measurement . 13
5.3.1 Rated output power . 13
5.3.1.1 Initial conditions . 13
5.3.1.2 Procedure . 13
5.3.1.3 Test requirements . 13
5.3.2 Frequency drift . 14
5.3.2.1 Initial conditions . 14
5.3.2.2 Procedure . 14
5.3.2.3 Test requirements . 14
5.3.3 Spurious emissions . 14
5.3.3.1 Initial conditions . 14
5.3.3.2 Procedure . 14
5.3.3.3 Test requirements . 15
5.3.4 Transmitter muting during frequency shift . 15
5.3.4.1 Initial conditions . 15
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 017 V2.0.3 (2016-12)
5.3.4.2 Procedure . 15
5.3.4.3 Test requirements . 15
5.3.5 Out-of-band emissions . 15
5.3.5.1 Initial conditions . 15
5.3.5.2 Procedure . 16
5.3.5.3 Test requirements . 16
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 17
Annex B (normative): General measuring arrangements . 18
B.1 Testing arrangements for antenna port measurements . 18
B.2 Test frequency range . 18
B.3 Test modulating signal . 19
B.4 Test load characteristics . 20
Annex C (informative): Change History . 21
History . 22
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 017 V2.0.3 (2016-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.4] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The present document describes the requirements for the design and operation of an AM sound broadcasting service
transmitter to meet the essential requirements of article 3.2 of Directive 2014/53/EU [i.1].
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 017 V2.0.3 (2016-12)
1 Scope
The present document specifies technical characteristics and methods of measurements for transmitter equipment for
broadcast sound services using the Double Side Band amplitude modulated sound broadcasting service operating in the
LF, MF and HF bands.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] ETSI TR 100 028-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 1".
[i.3] ETSI TR 100 028-2: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Uncertainties in the measurement of mobile radio equipment characteristics; Part 2".
[i.4] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 017 V2.0.3 (2016-12)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in Directive 2014/53/EU [i.1] and the
following apply:
antenna port: port of an apparatus which is designed, in normal operation, to be connected to an antenna using coaxial
cable
broadcasting service: radiocommunication service in which the transmissions are intended for direct reception by the
general public
NOTE: This service may include sound transmissions, television transmissions or other types of transmission.
carrier power: average power supplied to the antenna transmission line by a transmitter during one cycle taken under
the condition of no modulation
channel bandwidth: frequency band of defined width (as a multiple of the carrier grid) including safety margin for
operation on adjacent channels, located symmetrically around a carrier frequency in the carrier grid
class of emission: set of characteristics of an emission, designated by standard symbols, e.g. type of modulation of the
main carrier, modulating signal, type of information to be transmitted, and also, if appropriate, any additional signal
characteristics
dBc: decibels relative to the unmodulated carrier power of the emission
NOTE: In the cases which do not have a carrier, for example in some digital modulation schemes where the
carrier is not accessible for measurement, the reference level equivalent to dBc is decibels relative to the
mean power P.
enclosure port: physical boundary of the apparatus through which electromagnetic fields may radiate or impinge
NOTE: In the case of integral antenna equipment, this port is inseparable from the antenna port.
harmonic: component of order greater than 1 of the Fourier series of a periodic quantity
harmonic number: integral number given by the ratio of the frequency of a harmonic to the fundamental frequency
(second harmonic = 2 × fundamental frequency)
intermodulation products: unwanted frequencies resulting from intermodulation between carriers or harmonics of
emission, or between any oscillations generated to produce the carrier
mean power: average power supplied to the antenna transmission line by a transmitter during an interval of time
sufficiently long compared with the lowest frequency encountered in the modulati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.