SIST EN 12629-3:2004

Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines

1.1 This European standard applies to machines and assemblies for the manufacture of constructional products of calcium silicate or concrete, where the machnie has a turning or slide moving table in which the mould(s) is (are) mounted. The motive power for compressing the mixture is effected mechanically (annex A,B), or hydraulically (annex C, D).

Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 3: Drehtischmaschinen

1.1   Diese Norm gilt für Maschinen zur Herstellung von Bauprodukten aus Beton oder Kalksandsteinmassen, sofern eine oder mehrere Formen in die Dreh- oder Schiebetisch-Maschine eingebaut sind. Die Verdichtung der Mischung wird entweder mechanisch (Anhänge A, B) oder hydraulisch (Anhänge C, D) betrieben.
1.2   Diese Norm behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf diese Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet werden (siehe Abschnitt 4). Diese Norm spezifiziert die entsprechenden technischen Maßnahmen zur Beseitigung oder Reduzierung der Risiken, die von diesen Gefährdungen ausgehen.
1.3   Der Geltungsbereich dieser Norm beginnt für diese Maschinen bei der Zuführung der Mischung (siehe Punkt 1, Anhänge A, B, C, D), der Zuführung der Paletten für die Betonprodukte (siehe Punkt 8, Anhänge C, D) und endet an der Stelle, an der die Paletten mit den frischen Produkten die Anlage zur weiteren Verarbeitung verlassen (siehe Punkt 2, Anhänge A, B, C, D).
1.4   Diese Norm behandelt nicht die Anforderungen zur Verminderung von Gefährdungen durch mechanische, elektrische, pneumatische, hydraulische oder andere Bauteile oder Maschinen, die in den Normen für ihre allgemeine Verwendung (Typ A, B1 und B2-Normen) behandelt sind.
1.5   Diese Norm behandelt die in Abschnitt 4 aufgeführten Gefährdungen, außer Gefährdungen durch Lärm ), die während des Betriebs und der Wartung von Schiebe- und Drehtischmaschinen einschließlich der Schnittstellen auftreten können, wenn sie entsprechend den Angaben des Herstellers oder seines bevollmächtigten Vertreters betrieben werden.
ANMERKUNG   Eine Änderung ist in Vorbereitung, die Lärm behandelt sowie insbesondere Maßnahmen zur Lärmminderung an der Quelle und ein Geräuschmessverfahren einschließlich der Angabe von Geräuschemissionswerten.
Diese Norm behandelt Sicherheitsanforderungen und/oder Schutzverfahren, die für

Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 3: Machines a table coulissante et tournante

1.1. La présente norme européenne s'applique aux machines et installations utilisées pour la fabrication de produits de construction en silico-calcaire ou en béton, lorsque ces machines sont munies d'une table mobile coulissante ou tournante dans laquelle le(s) moule(s) est (sont) monté(s). La force motrice utilisée pour comprimer le mélange est d'origine mécanique (annexes A,B) ou hydraulique (annexes C, D).

Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 3. del: Drsni in vrtljivi stroji

General Information

• Status: Withdrawn
• Publication Date: 31-Aug-2004
• Withdrawal Date: 13-Oct-2010
• ICS: 91.220 - Construction equipment
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 13-Oct-2010
• Due Date: 05-Nov-2010
• Completion Date: 14-Oct-2010
• Directive: 98/37/EC - Machinery
• Mandate: M/BC/CEN/88/13 - Standardization request to CEN/CENELEC relating to machinery
• Ref Project: EN 12629-3:2002 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines

Relations

• Consolidated By: SIST EN 12629-3:2004+A1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines
• Effective Date: 18-Jan-2023
• Consolidated By: SIST EN 12629-3:2004+A1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines
• Effective Date: 19-Jan-2023
• Amended By: SIST EN 12629-3:2004/kFprA1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines
• Effective Date: 01-Apr-2010
• Consolidated By: SIST EN 12629-3:2004+A1:2010 - Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 3: Slide and turntable machines
• Effective Date: 01-Dec-2010

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 12629-3:2004
01-september-2004
6WURML]DL]GHODYRJUDGEHQLKSURL]YRGRYL]EHWRQDLQDSQHQHJDSHãþHQFD9DUQRVW
GHO'UVQLLQYUWOMLYLVWURML
Machines for the manufacture of constructional products from concrete and calcium-
silicate - Safety - Part 3: Slide and turntable machines
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen -
Sicherheit - Teil 3: Drehtischmaschinen
Machines pour la fabrication de produits de construction en béton et silico-calcaire -
Sécurité - Partie 3: Machines a table coulissante et tournante
Ta slovenski standard je istoveten z: EN 12629-3:2002
ICS:
91.220 Gradbena oprema Construction equipment
SIST EN 12629-3:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 12629-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2002
ICS 91.220
English version
Machines for the manufacture of constructional products from
concrete and calcium-silicate - Safety - Part 3: Slide and
turntable machines
Machines pour la fabrication de produits de construction en Maschinen für die Herstellung von Bauprodukten aus Beton
béton et silico-calcaire - Sécurité - Partie 3: Machines à und Kalksandsteinmassen - Sicherheit - Teil 3:
table coulissante et tournante Drehtischmaschinen
This European Standard was approved by CEN on 1 November 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12629-3:2002 E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 12629-3:2002 (E)
Contents
page
Foreword.3
Introduction .4
1 Scope .4
2 Normative references .5
3 Terms and definitions.5
4 List of significant hazards.6
4.1 Mechanical hazards (see informative annexes E, F, G, H) .6
4.2 Electrical hazards .9
4.3 Hazards generated by vibration .9
4.4 Hazards generated by materials and products.9
4.5 Hazards generated by neglecting ergonomic principles.9
4.6 Hazards caused by the failure of energy supply .9
5 Safety requirements and/or measures .9
6 Verification of safety measures and/or provisions .11
7 Information for use .11
8 Marking .11
Annex A (informative) Terminology for a common slide table machine .12
Annex B (informative) Terminology for a common turntable machine.13
Annex C (informative) Terminology for a common hydraulic turntable machine manufacturing
concrete products.14
Annex D (informative) Terminology for a common hydraulic slide table machine manufacturing
concrete products.15
Annex E (informative) Hazard zones and specific requirements for a common slide table machine .16
Annex F (informative) Hazard zones and specific requirements for a common turntable machine .17
Annex G (informative) Hazard zones and specific requirements for a hydraulic turntable machine
manufacturing concrete products.18
Annex H (informative) Hazard zones and specific requirements for a hydraulic slide table machine
manufacturing concrete products.19
Annex ZA (informative) Relationship of this document with EC Directives.20
Bibliography .21
2

---------------------- Page: 3 ----------------------

EN 12629-3:2002 (E)
Foreword
This document (EN 12629-3:2002) has been prepared by Technical Committee CEN /TC 151 "Construction
equipment and building material machines - Safety", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by June 2003, and conflicting national standards shall be withdrawn at the latest by
June 2003.
This document has been prepared under a mandate given to CEN by the European Commission and the European
Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative annex ZA, which is an integral part of this document.
The series "Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety"
consists of following Parts :
Part 1 : Common requirements
Part 2 : Block making machines
Part 3 : Slide and turntable machines
Part 4 : Concrete roof tile making machines
Part 5.1 : Concrete pipe machines manufacturing in the vertical axis.
Part 5.2 : Concrete pipe machines manufacturing in the horizontal axis
Part 5.3 : Pipe prestressing machines
Part 5.4 : Concrete pipe coating machines
Part 6 : Stationary and mobile equipment for the manufacture of precast reinforced products
Part 7 : Stationary and mobile equipment for the benched manufacture of prestressed products
Part 8 : Machines and equipment for the manufacture of constructional products from calcium silicate (and
concrete)
Annexes A to H are informative.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,
Sweden, Switzerland and the United Kingdom.
3

---------------------- Page: 4 ----------------------

EN 12629-3:2002 (E)
Introduction
This European Standard is a Type C-standard in the structure as stated in EN 1070.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines that
have been designed and built according to the provisions of this type C standard.
Reference to pertinent standards mentioned above is made where requirements of such standards are relevant.
1 Scope
1.1 This European Standard applies to machines for the manufacture of constructional products of calcium
silicate or concrete, where the mould(s) is (are) mounted on a turning or slide moving table. The motive power for
compressing the mixture is effected either mechanically (annexes A, B), or hydraulically (annexes C and D).
1.2 This European Standard deals with the hazards listed in clause 4 of machines for the manufacture of
constructional products from concrete and calcium silicate, when used as intended under the conditions foreseen
by the manufacturer. This European Standard specifies the appropriate technical measures to eliminate or reduce
risks arising from the significant hazards.
1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (see
point 1 of annexes A, B, C, D) and the point where the pallets for concrete products are brought to the assembly
(see point 8 at annexes C and D) until the point where the green products are removed from the machine to the
curing system (see point 2 of annexes A, B, C, D).
1.4 This European standard does not cover those requirements for reducing hazards from mechanical,
electrical, pneumatic, hydraulic or other equipment or machinery that are dealt with in standards for their common
use (Type A, B1 and B2 standards).
1.5 This European Standard deals with the hazards listed in clause 4 which can arise during the operation and
maintenance, including the interfaces, of the slide and turntable machines, when carried out in accordance with the
1)
specifications given by the manufacturer or his authorised representative, except noise hazards.
NOTE Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a
noise test code including noise declaration.
This standard establishes safety requirements and/or methods of protection which apply to these machines.
1.6 The provisions stated in this standard assume that all operators have been adequately informed and trained.

1) Until a noise test code (dealing with the measurement and declaration of noise emission values) specific to the machines
covered by this part is available to complement the requirements of 5.7.2 and 7.4.2 of EN 12629-1:2000, it cannot be
considered that noise hazards are covered.
4

---------------------- Page: 5 ----------------------

EN 12629-3:2002 (E)
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 292-1:1991, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology,
methodology.
EN 292-2, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical principles and
specifications.
EN 1070:1998, Safety of machinery — Terminology.
EN 12629-1:2000, Machines for the manufacture of constructional products from concrete and calcium-silicate –
Safety – Part 1: Common requirements.
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 1070:1998 apply.
Additional definitions found in EN 12629-1:2000 and those given below also apply to this standard.
For additional information, see also annexes A, B, C and D.
3.1
table
movable part of the machine in which the mould is fixed, recirculating mould machines (turntable) or forwards-
backwards (slide table)
3.2
ram
movable part of the machine which brings the compression force to the mixture in the mould
3.3
transmission levers
those parts of the machine that convert rotary motive power into reciprocal movement through gears and cams
3.4
take off device
integral part of the machine, that takes off the formed products (green) and puts them on a green product collection
system or arranges them into formation for removal from the machine
3.5
green product collection system
integral transport system which is part of the machine that carries the green product from the take off device to the
stacking equipment, or to the point where the green product is removed from the machine
3.6
stacking equipment
transport system which is an integral part of the machine that takes the green products from either the green
product collection system or the take off device and arranges them into formation for removal from the machine
3.7
drawing box
container having the shape of a box with an open or movable bottom. The drawing box fills the mould with the
mixture
5

---------------------- Page: 6 ----------------------

EN 12629-3:2002 (E)
3.8
feed hopper
device, only used with concrete product machines, that contains the mixture which is transported to the drawbox or
mould by a discharge gate
3.9
front mix dosing installation
device that doses the plastic or fluid face into the mould before the drawbox fills the back mix. It is only required
when producing two layer concrete slabs
3.10
brick wagon pusher
transport system which is an integral part of the machine which pushes the brick wagons from one position to the
other within the area of the stacking equipment. It is only used at machines producing
calcium-silicate products
3.11
pallet pusher
transport system which is an integral part of the assembly of the machine which pushes the pallets from one
position to an other or direct to the area where the take off device arranges the formed products into formation on
the pallets. It is only used at machines producing concrete products
3.12
pallet feeding unit
device only used with concrete product producing machines, which automatically supplies pallets or plates to the
pallet pusher or to the take off device from a store in the immediate proximity of the machine
4 List of significant hazards
This clause contains all hazards, as far as they are dealt with in this European Standard, identified by risk
assessment significant for this type of machinery and which require action to eliminate or reduce risk.
Before using this standard, it is important for the manufacturer to carry out a risk assessment of t
...