SIST EN 50636-2-92:2015
(Main)Household and similar electrical appliances - Safety - Part 2-92: Particular requirements for pedestrian-controlled mains-operated lawn scarifiers and aerators
Household and similar electrical appliances - Safety - Part 2-92: Particular requirements for pedestrian-controlled mains-operated lawn scarifiers and aerators
This clause of Part 1 is replaced by the following.
This European Standard specifies safety requirements and their verification for the design and
construction of pedestrian controlled walk-behind mains operated scarifiers and aerators, hereinafter
referred to as ‘machine(s)’, which are designed for re-generating lawns by, for instance, combing out
grass, thatch and moss or cutting vertically into the lawn face using tines which rotate about a
horizontal axis. This standard applies in conjunction with Part 1.
NOTE 1 Lawn scarifiers are also known as lawn rakes.
This European Standard does not apply to non-powered scarifiers and aerators, battery powered
scarifiers and aerators, vertical axis scarifiers and aerators or those aerators which cut into the soil by
means of a reciprocating motion and ride-on machines.
This European Standard does not apply to
– lawnmowers (EN 60335-2-77);
– lawn trimmers (EN 60335-2-91);
– lawn edge trimmers (EN 60335-2-91);
– lawn edgers, flail mowers, sickle-bar mowers or agricultural mowers.
This European Standard is not applicable to aerators/scarifiers which are manufactured before the
date of publication of this document.
This European Standard deals with all the significant hazards presented by pedestrian-controlled
lawn scarifiers and lawn aerators when they are used as intended and under conditions of misuse
which are reasonably foreseeable.
NOTE 2 Combustion engine machines are covered by EN 13684.
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-92: Besondere Anforderungen für handgeführte netzbetriebene Rasen-Vertikutierer und Rasen-Lüfter
Appareils électrodomestiques et analogues - Sécurité - Partie 2-92: Règles particulières pour les scarificateurs de gazon et les aérateurs fonctionnant sur le réseau et pour conducteur à pied
Gospodinjski in podobni električni aparati - Varnost - 2-92. del: Posebne zahteve za ročno upravljane rahljalnike in prezračevalnike travne ruše, priključene na električno omrežje
To točko 1. dela nadomešča naslednje besedilo.
Ta evropski standard določa varnostne zahteve in njihovo preverjanje za načrtovanje ter konstrukcijo ročno upravljanih rahljalnikov in prezračevalnikov, priključenih na električno omrežje, v nadaljnjem besedilu: »stroji«, ki so zasnovani za obnavljanje trate, in sicer na primer z izčesavanjem trave, slame in mahu ali navpičnim rezanjem v površino trate z uporabo zobcev, ki se vrtijo okoli vodoravne osi. Ta standard se uporablja v povezavi s 1. delom.
OPOMBA 1: Rahljalnikom zemlje se reče tudi grablje za trato.
Ta evropski standard se ne uporablja za nenapajane rahljalnike in prezračevalnike, baterijsko napajane rahljalnike in prezračevalnike, rahljalnike in prezračevalnike z navpično osjo ali tiste prezračevalnike, ki režejo v zemljo
s povratnim gibanjem, ter stroje s sedežem.
Ta evropski standard se ne uporablja za
– vrtne kosilnice (EN 60335-2-77);
– motorne kose za trate (EN 60335-2-91);
– motorne kose za robove trat (EN 60335-2-91);
– izdelovalce tratnih robov, gonilnike mlatilcev, kosilce s srpom na drogu ali poljedelske kosilce.
Ta evropski standard se ne uporablja za prezračevalnike/rahljalnike, izdelane pred izdajo tega dokumenta.
Ta evropski standard opisuje vsa večja tveganja, ki jih predstavljajo ročno upravljani rahljalniki in prezračevalniki travne ruše, kadar se uporabljajo v skladu z njihovim namenom in pod pogoji razumno predvidene nepravilne uporabe.
OPOMBA 2: Stroji z motorjem z zgorevanjem so obravnavani v standardu EN 13684.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50636-2-92:2015
01-april-2015
1DGRPHãþD
SIST EN 60335-2-92:2005
*RVSRGLQMVNLLQSRGREQLHOHNWULþQLDSDUDWL9DUQRVW GHO 3RVHEQH]DKWHYH
]DURþQRXSUDYOMDQHUDKOMDOQLNHLQSUH]UDþHYDOQLNHWUDYQHUXãHSULNOMXþHQHQD
HOHNWULþQRRPUHåMH
Household and similar electrical appliances - Safety - Part 2-92: Particular requirements
for pedestrian-controlled mains-operated lawn scarifiers and aerators
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-92:
Besondere Anforderungen für handgeführte netzbetriebene Rasen-Vertikutierer und
Rasen-Lüfter
Appareils électrodomestiques et analogues - Sécurité - Partie 2-92: Règles particulières
pour les scarificateurs de gazon et les aérateurs fonctionnant sur le réseau et pour
conducteur à pied
Ta slovenski standard je istoveten z: EN 50636-2-92:2014
ICS:
13.120 Varnost na domu Domestic safety
65.060.70 Vrtnarska oprema Horticultural equipment
SIST EN 50636-2-92:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50636-2-92:2015
---------------------- Page: 2 ----------------------
SIST EN 50636-2-92:2015
EUROPEAN STANDARD EN 50636-2-92
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2014
ICS 65.060.70 Supersedes EN 60335-2-92:2005
English Version
Household and similar electrical appliances - Safety - Part 2-92:
Particular requirements for pedestrian-controlled mains-operated
lawn scarifiers and aerators
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-92: Règles particulières pour les scarificateurs de ähnliche Zwecke - Teil 2-92: Besondere Anforderungen für
gazon et les aérateurs fonctionnant sur le réseau et pour handgeführte netzbetriebene Rasen-Vertikutierer und
conducteur à pied Rasen-Lüfter
This European Standard was approved by CENELEC on 2013-09-02. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50636-2-92:2014 E
---------------------- Page: 3 ----------------------
SIST EN 50636-2-92:2015
EN 50636-2-92:2014 – 2 –
Contents Page
Foreword . 4
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General requirement .10
5 General conditions for the tests .10
6 Classification .11
7 Marking and instructions .11
8 Protection against access to live parts .14
9 Starting of motor-operated appliances .14
10 Power input and current .14
11 Heating .15
12 Void .15
13 Leakage current and electric strength at operating temperature .15
14 Transient overvoltages .15
15 Moisture resistance .15
16 Leakage current and electric strength .15
17 Overload protection of transformers and associated circuits .15
18 Endurance .15
19 Abnormal operation .16
20 Stability and mechanical hazards .16
21 Mechanical strength .23
22 Construction .24
23 Internal wiring .25
24 Components .25
25 Supply connection and external flexible cords .26
26 Terminals for external conductors.27
27 Provision for earthing .27
28 Screws and connections .27
29 Clearances, creepage distances and solid insulation .27
30 Resistance to heat and fire .27
31 Resistance to rusting .27
32 Radiation, toxicity and similar hazards .27
Annex AA (normative) Safety signs and symbols .39
Annex BB (informative) Safety Instructions .42
---------------------- Page: 4 ----------------------
SIST EN 50636-2-92:2015
– 3 – EN 50636-2-92:2014
Annex CC (normative) Vibration .45
Annex DD (normative) Noise test code – Engineering method (grade 2) .50
Annex EE (informative) Example of a material and construction fulfilling the requirements
for an artificial surface .56
Annex FF (normative) Base .58
Annex ZZ (informative) Coverage of Essential Requirements of EU Directives .60
Bibliography .61
Figures
Figure 101 Safety distances – Machines with more than one axle . 28
Figure 102 Safety distances – Single axle machines . 29
Figure 103 Foot probe . 30
Figure 104 Strength of tine assembly . 31
Figure 105 Operator zone . 32
Figure 106 Front and rear guarding of tines . 33
Figure 107 Side guarding of tines . 34
Figure 108 Guarding of rear discharge machines . 35
Figure 109 Guarding of front discharge machines . 36
Figure 110 Thrown object test rig for rear discharge scarifiers with rigid tines . 37
Figure 111 Impact test fixture for handle insulation . 38
Figure AA.1 “Read operator’s manual” . 39
Figure AA.2 “Keep bystanders away” . 40
Figure AA.3 “WARNING – Beware of sharp tines, keep fingers and toes away. Remove plug
from mains before maintenance, adjusting, cleaning or if the cord is entangled or damaged.
Tines continue to rotate after the motor is switched off” . 40
Figure AA.4 “Keep supply flexible cord away from tines” . 41
Figure CC.1 – Examples of transducer location/orientation . 47
Figure CC.2 – Examples of transducer location/orientation for hand-arm vibration . 48
Figure DD.1 Microphone positions on the hemisphere (see Table DD.1) . 51
Figure EE.1 Sketch of the measurement surface covered with an artificial surface (not to
scale) . 57
Figure FF.1 Base detail. 58
Figure FF.2 Nail plan of base . 59
Tables
Table DD.1 Co-ordinates of microphone positions . 52
Table DD.2 Absorption coefficients . 53
---------------------- Page: 5 ----------------------
SIST EN 50636-2-92:2015
EN 50636-2-92:2014 – 4 –
Foreword
This document (EN 50636-2-92:2014) has been prepared by CLC/TC 116 "Safety of motor-operated
electric tools".
The following dates are fixed:
(dop) 2014-12-20
• latest date by which this document has to be
implemented
at national level by publication of an identical
national standard or by endorsement
• latest date by which the national standards conflicting (dow) 2016-09-02
with this document have to be withdrawn
This document supersedes EN 60335-2-92:2005.
EN 60335-2-92:2014 includes the following significant technical changes:
– rewording of some clauses;
– alignment to the European Machinery Directive 2006/42/EC;
– alignment to EN 60335-1:2012.
This document is to be used in conjunction with EN 60335-1:2012 “Household and similar electrical
appliances Safety Part 1: General requirements”.
When “Part 1” is mentioned in this standard, it refers to EN 60335-1:2012.
This document supplements or modifies the corresponding clauses in Part 1, so as to convert that
publication into the European Standard “Particular requirements for pedestrian-controlled walk-
behind mains operated scarifiers and aerators”.
Where a particular subclause of Part 1 is not mentioned in this document, that subclause applies as
far as is relevant. Where this standard states “addition”, “modification” or “replacement”, the relevant
text in Part 1 is to be adapted accordingly.
Compliance with the relevant clauses of Part 1 together with this document provides one means of
conforming to the specified essential health and safety requirements of the Directive.
This European Standard follows the overall requirements of EN ISO 12100.
Warning: Other requirements arising from other EU Directives can be applicable to the products
falling within the scope of this European Standard.
The following numbering system is used:
– subclauses , notes, tables and figures that are numbered starting from 101 are additional to
those in Part 1;
– additional annexes are lettered AA, BB, etc.;
Note In this European Standard the following print types are used:
- requirements proper: in roman type;
- test specifications: in italic type;
- explanatory matter: in smaller roman type.
Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated
noun are also in bold. Common modifications are indicated by a vertical line in the left margin of the text.
---------------------- Page: 6 ----------------------
SIST EN 50636-2-92:2015
– 5 – EN 50636-2-92:2014
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this
document.
---------------------- Page: 7 ----------------------
SIST EN 50636-2-92:2015
EN 50636-2-92:2014 – 6 –
Introduction
This document is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and events are
covered is as indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B
standards, the provisions of this type C standard take precedence over the other standards, for
machines which have been built and designed to the provisions of this type C standard.
---------------------- Page: 8 ----------------------
SIST EN 50636-2-92:2015
– 7 – EN 50636-2-92:2014
1 Scope
This clause of Part 1 is replaced by the following.
This European Standard specifies safety requirements and their verification for the design and
construction of pedestrian controlled walk-behind mains operated scarifiers and aerators, hereinafter
referred to as ‘machine(s)’, which are designed for re-generating lawns by, for instance, combing out
grass, thatch and moss or cutting vertically into the lawn face using tines which rotate about a
horizontal axis. This standard applies in conjunction with Part 1.
NOTE 1 Lawn scarifiers are also known as lawn rakes.
This European Standard does not apply to non-powered scarifiers and aerators, battery powered
scarifiers and aerators, vertical axis scarifiers and aerators or those aerators which cut into the soil by
means of a reciprocating motion and ride-on machines.
This European Standard does not apply to
– lawnmowers (EN 60335-2-77);
– lawn trimmers (EN 60335-2-91);
– lawn edge trimmers (EN 60335-2-91);
– lawn edgers, flail mowers, sickle-bar mowers or agricultural mowers.
This European Standard is not applicable to aerators/scarifiers which are manufactured before the
date of publication of this document.
This European Standard deals with all the significant hazards presented by pedestrian-controlled
lawn scarifiers and lawn aerators when they are used as intended and under conditions of misuse
which are reasonably foreseeable.
NOTE 2 Combustion engine machines are covered by EN 13684.
2 Normative references
This clause of Part 1 is applicable except as follows.
Addition:
EN 60335-1:2012, Household and similar electrical appliances Safety Part 1: General
requirements (IEC 60335-1:2010, modified)
EN ISO 354:1993, Acoustics Measurement of sound absorption in a reverberation room
(ISO 354:2003)
EN ISO 2758:2003, Paper Determination of bursting strength (ISO 2758:2001)
EN ISO 3744:2010, Acoustics Determination of sound power levels and sound energy levels of
noise sources using sound pressure Engineering methods for an essentially free field over a
reflecting plane (ISO 3744:2010)
EN ISO 4871:2009, Acoustics Declaration and verification of noise emission values of machinery
and equipment (ISO 4871:1996)
---------------------- Page: 9 ----------------------
SIST EN 50636-2-92:2015
EN 50636-2-92:2014 – 8 –
EN ISO 11201:2010, Acoustics Noise emitted by machinery and equipment Determination of
emission sound pressure levels at a work station and at other specified positions in an essentially free
field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 12100:2010, Safety of machinery General principles for design Risk assessment and
risk reduction (ISO 12100:2010)
EN ISO 13857:2008, Safety of machinery Safety distances to prevent hazard zones being reached
by upper and lower limbs (ISO 13857:2008)
EN ISO 20643:2008; Mechanical vibration Hand-held and hand-guided machinery Principles for
evaluation of vibration emission (ISO 20643:2005)
3 Terms and definitions
This clause of Part 1 is applicable except as follows.
3.1.9 Replacement:
3.1.9
normal operation
operation of the machine under the following conditions: the machine is operated at rated voltage
with the load necessary to attain rated power input
Addition:
3.101
braking system
combination of one or more brakes and related means of operation and control
3.102
catcher
part or combination of parts which provides a means for collecting grass, thatch, moss or other debris
3.103
control
means or device which will control the operation of the machine or any specific operating function
thereof
3.104
discharge chute
extension of the tine enclosure from the discharge opening, generally used to control the discharge
of material from the tines
3.105
discharge opening
gap or opening in the tine enclosure through which grass, thatch, moss and other debris may be
discharged.
a) front discharge
denotes throwing out grass, thatch and moss so that they will be collected in a catcher which is
located in front of the tines
b) rear discharge
denotes throwing out grass, thatch and moss so that they will be collected in a catcher which is
located behind the tines
---------------------- Page: 10 ----------------------
SIST EN 50636-2-92:2015
– 9 – EN 50636-2-92:2014
3.106
guard
part of the machine or component incorporated to provide protection for the operator and/or bystander
by means of a physical barrier
3.107
handle
any part likely to be hand-held for guiding the machine in normal use
3.108
hit
test projectile passing completely through all layers of the target material
3.109
intended use
any use of the machine which is reasonably foreseeable, as described in the user instructions, and
which is consistent with such activities as operating, starting, stopping or connecting to (or
disconnecting from) a mains supply
3.110
lawn aerator
corer
machine which uses the ground to determine the depth of cut, designed for penetrating the lawn
surface
3.111
lawn scarifier
machine designed to scratch the surface, or earth face thereby also combing the lawn
3.112
maximum operating motor speed
highest motor speed obtainable when the motor is adjusted in accordance with the instructions, with
the tines engaged
3.113
operator control
any control requiring the operator’s actuation to perform specific functions
3.114
operator presence control
control designed so that it will automatically interrupt power to a drive when the operator's actuating
force is removed
3.115
operator zone
zone for persons operating a lawn scarifier or aerator (presented in Figure 105)
3.116
parking brake
device incorporated into the machine which, when operated, prevents the machine from moving from
a stationary position and remains applied without the operator present
3.117
pedestrian-controlled
ground-supported, controlled by an operator walking behind
---------------------- Page: 11 ----------------------
SIST EN 50636-2-92:2015
EN 50636-2-92:2014 – 10 –
3.118
service brake
designated primary means for decelerating and stopping a machine from its ground travel speed
3.119
tine
mechanism used to provide the penetrating or scratching action of a machine
3.120
tine enclosure
part or assembly which provides the protective means around the tines
3.121
tine tip circle
path described by the outermost point of the tine as it rotates about its shaft axis
3.122
traction drive
means (system) used to transmit power from the motor to the ground drive means
3.123
width of cut
total width of scarification/aeration measured across the tines at right angles to the direction of travel
3.124
working position
any depth setting of the tines designated by the manufacturer
4 General requirement
This clause of Part 1 is applicable.
5 General conditions for the tests
This clause of Part 1 is applicable except as follows.
5.2 Addition:
Tests carried out in Clauses 20 and 21 require a new machine for each test. If testing requires the
same test to be carried out on the machine for different functions a new machine shall be used for
each test.
5.5 Addition:
During the tests the tines are adjusted in accordance with the manufacturer's instructions.
5.6 Addition:
Electronic speed control devices are set for the maximum operating motor speed.
---------------------- Page: 12 ----------------------
SIST EN 50636-2-92:2015
– 11 – EN 50636-2-92:2014
6 Classification
This clause of Part 1 is applicable except as follows.
6.1 Replacement:
Machines shall be of class II with respect to protection against electric shock.
Compliance is checked by inspection and by the relevant tests.
6.2 Addition:
Machines shall be at least IPX4.
7 Marking and instructions
This clause of Part 1 is applicable except as follows.
7.1 Addition:
The machines shall be marked with the following minimum information:
– business name and full address of the manufacturer and, where applicable his authorized
representative;
– designation of the machine,
designation of machine may be achieved by a combination of letters and/or numbers. The
designation may be provided in the form of a code, providing that this code is explained by giving
the explicit designation such as “scarifiers” or “aerators”, etc. in the instructions supplied with the
machine;
NOTE 1 An example of such code is “A123B”.
– year of construction, that is the year in which the manufacturing process is completed;
– designation of series or type,
allowing the technical identification of the product. This may be achieved by a combination of letters and/or
numbers and may be combined with the designation of machine;
NOTE 2 The term “designation of series or type” is also known as model number.
– serial number, if any;
– rated power in watts or rated current in amperes;
– guards designed to be opened or removed shall have a sign warning of the relevant hazard
visible on the machine both when the guard is closed and when it is opened or removed;
– controls which may give rise to a hazard (e.g. operator presence control for the tines) when
operated shall be marked or so placed as to indicate clearly which part of the machine they
control;
– mandatory markings;
NOTE 3 For machines and their related products intended to be put on the market in the EEA, CE-marking as defined in
the applicable European Directive(s), e.g. the Machinery Directive.
Where replaceable during normal use, except for spring type tines, the tines shall be marked to
identify the part number(s) and the manufacturer, importer or supplier.
---------------------- Page: 13 ----------------------
SIST EN 50636-2-92:2015
EN 50636-2-92:2014 – 12 –
Marking giving warning information shall be easily legible and located as close as practicable to the
relevant hazard.
The substance of the following warnings shall be placed in a prominent position on the machine:
– WARNING – Read user instructions;
– WARNING – Beware of sharp tines, keep fingers and toes away. Remove plug from mains
before maintenance, adjusting, cleaning or if the cord is entangled or damaged;
– Tines continue to rotate after the motor is switched off;
– Keep flexible cord away from the tines;
– Keep bystanders away,
and as appropriate to the machine design:
– Wear eye and/or ear protection.
If a pictogram is used it shall be that shown in Annex AA. It shall be in contrasting colours to the base
material. If it is embossed, stamped or cast colours are not required. Markings or safety signs giving
cautionary information shall be located close to the hazard.
Compliance shall be checked by inspection.
7.6 Addition:
NOTE 101 Information on operator symbols may be found in EN ISO 3767-1 and EN ISO 3767-3, ISO 11684 and in ISO 3864
for colours.
7.12 Replacement:
An instruction manual shall be supplied with the machine, giving operating, servicing, maintenance
and safety instructions that comply as appropriate with EN ISO 12100:2010, 6.4. The words ‘Original
instructions’ shall appear on the language version(s) verified by the manufacturer or his authorised
representative. Where no ‘Original instructions’ exist in the official language(s) of the country where
the machine is to be used, a translation into that/those language(s) shall be provided by the
manufacturer or his authorised representative or by the person bringing the machine into the language
area in question. The translations shall bear the words ‘Translation of the original instructions’, and
they shall be accompanied by a copy of the ‘Original instructions’.
This instruction manual shall include:
a) a repeat of those warnings required to be marked on the machine together with further
explanation, where appropriate. Where safety signs are used in the marking on the machine, their
function shall be explained;
b) a warning to never allow children, persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge or people unfamiliar with these instructions to use the machine,
local regulations may restrict the age of the operator;
c) a warning to never operate the machine while people, especially children, or pets are nearby;
d) a general description of the machine, the intended use, instructions for the proper use of the
machine including advice on what the machine should be used for, how to use it for the intended
purpose(s) and any reasonably foreseeable misuse thereof;
e) warnings concerning ways - that experience has shown might occur - in which the machinery shall
not be used;
f) instructions for the proper assembly and disassembly of the machine for use, if the machine is not
supplied in a completely assembled form;
---------------------- Page: 14 ----------------------
SIST EN 50636-2-92:2015
– 13 – EN 50636-2-92:2014
g) instructions
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.