SIST EN ISO 8560:2019
(Main)Technical drawings - Construction drawings - Representation of modular sizes, lines and grids (ISO 8560:2019)
Technical drawings - Construction drawings - Representation of modular sizes, lines and grids (ISO 8560:2019)
This document lays down rules for the representation of modular sizes, lines and grids on construction
drawings. The basic module M is 100 mm (see ISO 1006).
Generally, modular sizes are for use on design drawings, but can also be added to production drawings
for manufacturing, orientation and location.
Technische Zeichnungen - Zeichnungen für das Bauwesen - Darstellung von modularen Größen, Linien und Rastern (ISO 8560:2019)
Dessins techniques - Dessins de construction - Représentation des dimensions, lignes et quadrillages modulaires (ISO 8560:2019)
Le présent document établit des règles pour la représentation des dimensions, lignes et quadrillages modulaires sur des dessins de construction. Le module de base M est de 100 mm (voir l'ISO 1006).
En général, les dimensions modulaires sont destinées à être utilisées sur des dessins de construction, mais elles peuvent également être ajoutées sur les dessins de production pour la fabrication et la construction, pour l'orientation et l'emplacement.
Tehnične risbe - Gradbeniške risbe - Prikazovanje modulskih mer, črt in mrež (ISO 8560:2019)
Ta dokument določa pravila za prikazovanje modulskih mer, črt in mrež na gradbeniških
risbah. Osnovni modul M je 100 mm (glej ISO 1006).
Na splošno se modulske mere uporabljajo pri risbah zasnove, vendar jih je mogoče dodati tudi proizvodnim risbam
za proizvodnjo, usmerjenost in lokacijo.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8560:2019
01-julij-2019
Nadomešča:
SIST EN ISO 8560:2002
Tehnične risbe - Gradbeniške risbe - Prikazovanje modulskih mer, črt in mrež (ISO
8560:2019)
Technical drawings - Construction drawings - Representation of modular sizes, lines and
grids (ISO 8560:2019)
Technische Zeichnungen - Zeichnungen für das Bauwesen - Darstellung von modularen
Größen, Linien und Rastern (ISO 8560:2019)
Dessins techniques - Dessins de construction - Représentation des dimensions, lignes et
quadrillages modulaires (ISO 8560:2019)
Ta slovenski standard je istoveten z: EN ISO 8560:2019
ICS:
01.100.30 Gradbeni načrti Construction drawings
SIST EN ISO 8560:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8560:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 8560:2019
EN ISO 8560
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2019
EUROPÄISCHE NORM
ICS 01.100.30 Supersedes EN ISO 8560:1999
English Version
Technical drawings - Construction drawings -
Representation of modular sizes, lines and grids (ISO
8560:2019)
Dessins techniques - Dessins de construction - Technische Zeichnungen - Zeichnungen für das
Représentation des dimensions, lignes et quadrillages Bauwesen - Darstellung von modularen Größen, Linien
modulaires (ISO 8560:2019) und Rastern (ISO 8560:2019)
This European Standard was approved by CEN on 22 March 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8560:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8560:2019
EN ISO 8560:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8560:2019
EN ISO 8560:2019 (E)
European foreword
This document (EN ISO 8560:2019) has been prepared by Technical Committee ISO/TC 10 "Technical
product documentation" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2019, and conflicting national standards
shall be withdrawn at the latest by November 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 8560:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 8560:2019 has been approved by CEN as EN ISO 8560:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8560:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 8560:2019
INTERNATIONAL ISO
STANDARD 8560
Second edition
2019-04
Technical drawings — Construction
drawings — Representation of
modular sizes, lines and grids
Dessins techniques — Dessins de construction — Représentation des
dimensions, lignes et quadrillages modulaires
Reference number
ISO 8560:2019(E)
©
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 8560:2019
ISO 8560:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8560:2019
ISO 8560:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 1
5 Designations of modular sizes . 1
6 Representation of modular lines and sizes . 2
6.1 General . 2
6.2 Modular and multimodular lines . 2
6.3 Modular line in an axial position . 2
6.4 Circle for identification of modular line . 2
6.5 Designation of modular line . 2
6.6 Terminations for the size of a modular zone . 3
7 Representation of modular grids . 3
7.1 General . 3
7.2 Modular grid with different line intervals . 3
7.3 Indication of modular sizes . 3
7.4 Indication of modular zones .
...
SLOVENSKI STANDARD
oSIST prEN ISO 8560:2019
01-februar-2019
7HKQLþQHULVEH*UDGEHQLãNHULVEH3ULND]RYDQMHPRGXODUQLKPHUþUWLQPUHå
,62)',6
Technical drawings - Construction drawings - Representation of modular sizes, lines and
grids (ISO/FDIS 8560:2018)
Technische Zeichnungen - Zeichnungen für das Bauwesen - Darstellung von modularen
Größen, Linien und Rastern (ISO/FDIS 8560:2018)
Dessins techniques - Dessins de construction - Représentation des dimensions, lignes et
quadrillages modulaires (ISO/FDIS 8560:2018)
Ta slovenski standard je istoveten z: prEN ISO 8560
ICS:
01.100.30 *UDGEHQLQDþUWL Construction drawings
oSIST prEN ISO 8560:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 8560:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 8560:2019
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 8560
ISO/TC 10/SC 8
Technical drawings — Construction
Secretariat: SIS
drawings — Representation of
Voting begins on:
20181129 modular sizes, lines and grids
Voting terminates on:
Dessins techniques — Dessins de construction — Représentation des
20190221
dimensions, lignes et quadrillages modulaires
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 8560:2018(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2018
---------------------- Page: 3 ----------------------
oSIST prEN ISO 8560:2019
ISO/FDIS 8560:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 8560:2019
ISO/FDIS 8560:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 1
5 Designations of modular sizes . 1
6 Representation of modular lines and sizes . 2
6.1 General . 2
6.2 Modular and multimodular lines . 2
6.3 Modular line in an axial position . 2
6.4 Circle for identification of modular line . 2
6.5 Designation of modular line . 2
6.6 Terminations for the size of a modular zone . 3
7 Representation of modular grids . 3
7.1 General . 3
7.2 Modular grid with different line intervals . 3
7.3 Indication of modular sizes . 3
7.4 Indication of modular zones . 4
7.5 Indication of a change in direction of a modular grid . 4
7.6 Indication of the displacement of a modular grid . 5
7.7 Indication of a modular line in an axial position . 5
8 Combination of modular sizes and work sizes on the same drawing .6
Bibliography . 7
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 8560:2019
ISO/FDIS 8560:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardizati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.