SIST-TS CLC/TS 50131-11:2012
(Main)Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices
Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices
This Technical Specification is for dedicated hold-up devices in buildings, e.g. deliberately operated hold-up devices which can be triggered to create a hold-up alarm signal or message. It provides four security Grades 1-4 (see EN 50131-1), specific or non specific wired or wire-free hold-up devices and uses Environmental Classes I-IV (see EN 50130-5). This Technical Specification does not include requirements for hold-up devices intended for use outdoors, or for mobile hold-up devices or for devices with functions additional to hold-up facility. NOTE If a device provides functions additional to hold-up facility, it is recommended to function similar to the requirement described in this Technical Specification. Functions additional to the mandatory functions as specified in this Technical Specification may be included in the hold-up device, providing they do not adversely influence the correct operation of the mandatory functions. This Technical Specification does not apply to system interconnections.
Alarmanlagen - Einbruch- und Überfallmeldeanlagen - Teil 11: Anforderungen an Überfallmelder
Systèmes d’alarme - Systèmes d'alarme contre l’intrusion et les hold-up - Partie 11: Exigences pour bouton anti-agression
Alarmni sistemi - Sistemi za javljanje vloma in ropa - 11. del: Zahteve za javljalnike ropa
Ta tehnična specifikacija je namenjena namenskim napravam za javljanje vloma v objektih, npr. namerno upravljane naprave za javljanje vloma, ki lahko ob sprožitvi proizvedejo alarm ali sporočilo o vlomu. Določa štiri varnostne razrede 1–4 (glejte standard EN 50131-1), specifične ali nespecifične ožičene ali brezžične naprave za javljanje vloma ter uporablja okoljske razrede I–IV (glejte standard EN 50130-5). Ta tehnična specifikacija ne zajema zahtev za naprave za javljanje vloma, ki so namenjene za uporabo na prostem, ali za mobilne naprave za javljanje vloma ali za naprave, ki poleg funkcije javljanja vloma vključujejo še druge funkcije. OPOMBA: Če naprava poleg funkcije javljanja vloma zagotavlja dodatne funkcije, je priporočeno, da deluje na način, ki je podoben zahtevi iz te tehnične specifikacije. Poleg obveznih funkcij, ki so opredeljene v tej tehnični specifikaciji, ima lahko naprava za javljanje vloma tudi dodatne funkcije, pri čemer te ne smejo neugodno vplivati na pravilno delovanje obveznih funkcij. Ta tehnična specifikacija se ne uporablja za povezave sistema.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TS CLC/TS 50131-11:2012
01-september-2012
Alarmni sistemi - Sistemi za javljanje vloma in ropa - 11. del: Zahteve za javljalnike
ropa
Alarm systems - Intrusion and hold-up systems - Part 11: Hold-up devices
Alarmanlagen - Einbruch- und Überfallmeldeanlagen - Teil 11: Anforderungen an
Überfallmelder
Systèmes d’alarme - Systèmes d'alarme contre l’intrusion et les hold-up - Partie 11:
Exigences pour bouton anti-agression
Ta slovenski standard je istoveten z: CLC/TS 50131-11:2012
ICS:
13.310 Varstvo pred kriminalom Protection against crime
13.320 Alarmni in opozorilni sistemi Alarm and warning systems
SIST-TS CLC/TS 50131-11:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CLC/TS 50131-11:2012
---------------------- Page: 2 ----------------------
SIST-TS CLC/TS 50131-11:2012
TECHNICAL SPECIFICATION
CLC/TS 50131-11
SPÉCIFICATION TECHNIQUE
August 2012
TECHNISCHE SPEZIFIKATION
ICS 13.310
English version
Alarm systems -
Intrusion and hold-up systems -
Part 11: Hold-up devices
Systèmes d’alarme - Alarmanlagen -
Systèmes d'alarme contre l’intrusion et les Einbruch- und Überfallmeldeanlagen -
hold-up - Teil 11: Anforderungen an Überfallmelder
Partie 11: Exigences pour bouton anti-
agression
This Technical Specification was approved by CENELEC on 2012-07-09.
CENELEC members are required to announce the existence of this TS in the same way as for an EN and to
make the TS available promptly at national level in an appropriate form. It is permissible to keep conflicting
national standards in force.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. CLC/TS 50131-11:2012 E
---------------------- Page: 3 ----------------------
SIST-TS CLC/TS 50131-11:2012
CLC/TS 50131-11:2012 - 2 -
Contents
Page
Foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions and abbreviations . 7
3.1 Terms and definitions . 7
3.2 Abbreviations . 8
4 Functional requirements . 8
4.1 General . 8
4.2 Event processing . 8
4.3 Hold-up triggering .10
4.4 Hand operated devices .12
4.5 Kick / tilt & long bar operated devices .13
4.6 Money clip operated devices .14
4.7 Operational requirements .15
4.8 Tamper security .16
4.9 Electrical requirements .17
4.10 Environmental classification and conditions .18
5 Marking, identification and documentation .18
5.1 Marking and/or identification.18
5.2 Documentation .18
6 Testing .19
6.1 General .19
6.2 General test conditions .19
6.3 Hand operated devices .21
6.4 Kick / tilt & Long bar operated devices .23
6.5 Money clip operated hold-up devices .24
6.6 Time interval between hold-up trigger signals or messages .24
6.7 Switch on delay .24
6.8 Self tests .24
6.9 Tamper security .25
6.10 Electrical tests .27
6.11 Environmental classification and conditions .29
6.12 Marking, identification and documentation .30
Annex A (normative) Dimensions & requirements of the standardised test magnets .31
Annex B (normative) General testing matrix .34
Annex C (informative) Example list of small tools .36
Bibliography .37
---------------------- Page: 4 ----------------------
SIST-TS CLC/TS 50131-11:2012
- 3 - CLC/TS 50131-11:2012
Figures
Figure A.1 — Magnet type 1.32
Figure A.2 — Magnet type 2.33
Tables
Table 1 — Events to be processed and functions to be provided by grade . 9
Table 2 — Generation of signals or messages .10
Table 3 — Sound level when triggering by grade .11
Table 4 — Operating force for hand operated hold-up devices .12
Table 5 — Minimum performance requirements for hand operated lever hold-up devices .13
Table 6 — Operating force for kick / tilt & long bar operated hold-up devices .14
Table 7 — Operating force for money clip operated devices .15
Table 8 — Tamper security requirements .16
Table 9 — Electrical requirements .17
Table 10 — Operational tests .29
Table 11 — Endurance tests .30
Table B.1 — General testing matrix .34
---------------------- Page: 5 ----------------------
SIST-TS CLC/TS 50131-11:2012
CLC/TS 50131-11:2012 - 4 -
Foreword
This document (CLC/TS 50131-11:2012) has been prepared by CLC/TC 79 "Alarm systems".
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
---------------------- Page: 6 ----------------------
SIST-TS CLC/TS 50131-11:2012
- 5 - CLC/TS 50131-11:2012
Introduction
This document is a Technical Specification for hold-up devices which can be used as part of intrusion
and hold-up alarm systems installed in buildings. It includes four security grades and four
environmental classes.
The purpose of a hold-up device is to allow a person to deliberately generate hold-up alarm signals or
messages and a further necessary range of signals or messages to be used by the rest of the
intrusion and hold-up alarm system.
The number and scope of these signals or messages will be more comprehensive for systems that are
specified at the higher grades.
This Technical Specification is only concerned with the requirements and tests for the hold-up device.
---------------------- Page: 7 ----------------------
SIST-TS CLC/TS 50131-11:2012
CLC/TS 50131-11:2012 - 6 -
1 Scope
This Technical Specification is for dedicated hold-up devices in buildings, e.g. deliberately operated
hold-up devices which can be triggered to create a hold-up alarm signal or message. It provides four
security Grades 1-4 (see EN 50131-1), specific or non specific wired or wire-free hold-up devices and
uses Environmental Classes I-IV (see EN 50130-5).
This Technical Specification does not include requirements for hold-up devices intended for use
outdoors, or for mobile hold-up devices or for devices with functions additional to hold-up facility.
NOTE If a device provides functions additional to hold-up facility, it is recommended to function similar to the requirement
described in this Technical Specification.
Functions additional to the mandatory functions as specified in this Technical Specification may be
included in the hold-up device, providing they do not adversely influence the correct operation of the
mandatory functions.
This Technical Specification does not apply to system interconnections.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 50130-4, Alarm systems – Part 4: Electromagnetic compatibility – Product family standard:
Immunity requirements for components of fire, intruder, hold up, CCTV, access control and social
alarm systems
EN 50130-5, Alarm systems – Part 5: Environmental test methods
EN 50131-1:2006 + A1:2009, Alarm systems – Intrusion systems and hold-up systems – Part 1:
System requirements
EN 60068-1:1994, Environmental testing – Part 1: General and guidance (IEC 60068-1:1988 +
corrigendum Oct. 1988 + A1:1992)
EN 60068-2-52, Environmental testing – Part 2: Tests – Test Kb: Salt mist, cyclic (sodium chloride
solution) (IEC 60068-2-52)
EN 60404-5, Magnetic materials – Part 5: Permanent magnet (magnetically hard) materials – Methods
of measurement of magnetic properties (IEC 60404-5)
EN 60404-14, Magnetic materials – Part 14: Methods of measurement of the magnetic dipole moment
of a ferromagnetic material specimen by the withdrawal or rotation method (IEC 60404-14)
EN 61672-1:2003, Electroacoustics – Sound level meters – Part 1 : Specifications (IEC 61672-1:2002)
IEC 60404-8-1, Magnetic materials – Part 8-1: Specifications for individual materials – Magnetically
hard materials
---------------------- Page: 8 ----------------------
SIST-TS CLC/TS 50131-11:2012
- 7 - CLC/TS 50131-11:2012
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 50131-1:2006 + A1:2009 and
the following apply.
3.1.1
basic activation test
operational test during which a hold-up device is activated by using the standard triggering method in
a controlled environment
3.1.2
hand operated devices
button, lever or strip operated hold-up devices, in which the hold-up trigger is activated by pressing
one or more button(s) or strip(s) or by pulling one or more lever(s), and the operation is intended to be
performed manually by hand
3.1.3
hold-up trigger
event which generates a hold-up signal or message when a hold-up device is activated by using the
standard triggering method
3.1.4
incorrect operation
physical condition that causes an inappropriate signal or message from a hold-up device
3.1.5
kick / tilt & long bar operated devices
hold-up devices in which the hold-up trigger is activated by pressing or lifting a floor or desk mounted
component, and the operation is intended to be performed manually by foot or knee
3.1.6
latching device
device that, following its operation, remains in the operated condition until reset before a further trigger
operation can be performed
3.1.7
masking
interference with the hold-up device input capability which prohibits the triggering of the hold-up device
e.g. controlling a reed switch based detection element by a separate magnet
3.1.8
money clip operated devices
hold-up devices in which the hold-up trigger is activated by deliberate removal of a banknote for trigger
activation
3.1.9
multi action devices
one or more component(s) of a hold-up devices capable of sending two or more hold-up trigger as a
result of two or more different methods of operation for verification purpose, whenever a verification is
required / applicable
EXAMPLE An example of different methods of operation could be the simultaneous push of two buttons to create an
unconfirmed hold-up trigger release the buttons, followed by a simultaneous push and holding in the same buttons a second
time for a predetermined period to create a confirmed hold-up trigger.
---------------------- Page: 9 ----------------------
SIST-TS CLC/TS 50131-11:2012
CLC/TS 50131-11:2012 - 8 -
3.1.10
non-latching device
device that, following its operation and after removal of the operating force(s), returns to its original
state and is able to generate further hold-up triggers when operated
3.1.11
operating member
component of an operating part requiring a specifically applied force or action to allow the activation of
the operating part
EXAMPLE One button of a hold-up device with two buttons, so each individual button will be an operating member.
3.1.12
operating part
deliberately operated part of a hold-up device requiring a specifically applied force to generate a hold-
up trigger when all required operating members are activated
EXAMPLE A hold-up device with two buttons, in which both buttons form an operating part and each individual button will
be an operating member.
3.2 Abbreviations
For the purposes of this document, the following abbreviations apply.
BAT Basic Activation Test
CIE Control & Indicating Equipment
EMC Electro Magnetic Compatibility
4 Functional requirements
4.1 General
A hold-up device shall fulfil all the requirements of the specified grade.
The functional requirements described in this clause shall cover the following types of hold-up devices,
which shall be tested towards the requirements according to the test methods described in Clause 6:
– hand operated hold-up devices (intended to be triggered by hand);
– kick / tilt & Long bar – Hold-up device (intended to be triggered via foot, knee);
– money clip contact – Hold-up device (intended to be triggered when a banknote is withdrawn).
4.2 Event processing
Hold-up devices shall process the events shown in Table 1. Hold-up devices shall generate signals or
messages as shown in Table 2.
---------------------- Page: 10 ----------------------
SIST-TS CLC/TS 50131-11:2012
- 9 - CLC/TS 50131-11:2012
Table 1 — Events to be processed and functions to be provided by grade
Event Grade
1 2 3 4
Hold-up trigger M M M M
Tamper detection Op M M M
Masking detection Op Op M M
a
Op M M M
Removal from the mounting surface
b
Op Op Op M
Low supply voltage
b
Total loss of power supply Op M M M
c
Local self test Op Op M M
Remote self test Op Op Op M
Key
M = Mandatory, Op = Optional
a
Mandatory for wire-free at grades 2, 3 and 4; mandatory for all surface mounted grade 4 types. Optional
for wired surface mounted grades 1, 2 and 3. Optional for wired flush mount hold-up devices.
b
Mandatory for wire-free at all grades. Only required if power is required for normal local operation, e.g.
purely micro or reed switch based solutions do not fall under this requirement. No generation of a
message or signal is required when the condition is detected by the CIE due to system design, e.g. bus
based systems.
c
Mandatory for grade 4. For grade 3 only required if software or firmware based signal processing is used
to generate any signal or message, e.g. purely micro switch or reed switch based solutions or solutions
which are based on analogue electronic design, do not fall under this requirement. No generation of a
message or signal is required when the condition is detected by the CIE due to system design, e.g. bus
based systems.
---------------------- Page: 11 ----------------------
SIST-TS CLC/TS 50131-11:2012
CLC/TS 50131-11:2012 - 10 -
Table 2 — Generation of signals or messages
Event Signals or Messages
Hold-up Tamper Fault
No event NP NP NP
Hold-up trigger M NP NP
Tamper NP M NP
a
NP M M
Masking
NP M NP
Removal from the mounting surface
Low supply voltage NP Op M
b
Total loss of power supply NP M Op
Local self test pass NP NP NP
Local self test fail NP NP M
Remote self test pass NP M NP
Remote self test fail NP NP M
Key
M = Mandatory, NP = Not Permitted, Op = Optional
When, in Table 1, an event may optionally generate signals or messages, they shall be
as shown in this table.
This permits two methods of signalling a masking event: either by the tamper signal
and fault signal, or by a dedicated masking signal or message. Use of the tamper
signal and fault signal is preferable, as this requires fewer connections between CIE
and hold-up device. If multiple events overlap there will be some signal combinations
that may be ambiguous. To overcome this ambiguity it is suggested that hold-up
devices should not signal ‘tamper‘ and ‘fault‘ at the same time except to indicate
masking. This implies that the hold-up device should prioritise signals, e.g. 1 Tamper, 2
Fault, 3 Masking.
It is accepted that a bus system, a bus-based device may send out dedicated signals
or messages and does not necessarily have to follow the mapping of Table 2 provided
that all of the required events are communicated.
a An independent signal or message may be provided instead.
b Alternatively Total loss of Power Supply shall be determined by loss of communication with the hold-up
device.
4.3 Hold-up triggering
4.3.1 Trigger operation
4.3.1.1 General
A hold-up trigger shall be generated when the hold-up device specific trigger mechanism is activated.
Hold-up devices shall include means to minimise the possibility of accidental triggering and fulfil the
device specific individual conditions according to the following subclauses.
The requirements, operation and responses of latching and non-latching devices are different.
All relevant trigger activations shall be tested according to the device type as required by the
corresponding test in Clause 6.
---------------------- Page: 12 ----------------------
SIST-TS CLC/TS 50131-11:2012
- 11 - CLC/TS 50131-11:2012
In case of multi-action devices, each individual trigger operation shall be tested separately and apply
to each corresponding test subclause in Clause 6. Furthermore, it shall be tested and assured, that
each trigger operation does not adversely affect the other trigger operation(s) unless a certain
sequence is required to generate the expected signals or messages, as described in the
manufacturer's manual.
If additional trigger activation methods to the ones described in this document exist for a specific
product, those shall be documented by the manufacturer in the installation document and user guide
and shall be tested accordingly.
4.3.1.2 Trigger indication
An indicator shall be provided at the device to indicate when a hold-up signal or message has been
generated.
It is permitted that the device can provide a function to disable the trigger indication.
The trigger indication shall be tested to identify triggered hold-up device(s).
The trigger indication shall remain activate on non-latching devices after the first hold-up trigger has
been generated.
Reset of the trigger indication shall be possible only using a suitable tool or mechanism.
4.3.1.3 Reapplied triggering
Following a hold-up trigger, non latching hold-up devices shall be capable of generating a further hold-
up signal or message in response to a trigger within 10s of the previous successful trigger operation.
Non-latching hold-up devices shall allow manual trigger operation within a maximum of 10 s after a
previous trigger operation has been performed successfully.
Latching hold-up devices shall remain in the operated condition after a trigger operation has been
performed successfully and shall require resetting using a suitable tool or mechanism before a further
trigger operation can be performed.
4.3.1.4 Sound level when triggering
When installed and operated according to the manufacturer instructions, the sound level when
triggering shall not be greater than the value given in Table 3 at a distance of 1 m in an anechoic
chamber:
Table 3 — Sound level when triggering by grade
All values are given in dB(A)
Type of hold-up device Grade
1 2 3 4
Hand operated hold-up devices (Type V, W, X, Y & Z) ≤ 60 ≤ 60 ≤ 50 ≤ 30
Kick / tilt & long bar operated devices (Type A, B & C) ≤ 60 ≤ 60 ≤ 60 ≤ 30
Money clip operated devices (Type K & L) ≤ 60 ≤ 60 ≤ 50 ≤ 30
---------------------- Page: 13 ----------------------
SIST-TS CLC/TS 50131-11:2012
CLC/TS 50131-11:2012 - 12 -
4.4 Hand operated devices
4.4.1 Manual deliberately trigger operation
Hand operated hold-up devices shall only generate a hold-up signal or message through a deliberate
manual operation. Means, methods or techniques shall be used to reduce the risk of accidental
operation of a hand operated hold-up device (e.g. certain minimum force required to press a button or
pull a lever, two buttons pressed simultaneously, flipping of a protective cover to operate a button),
according to this Technical Specification.
The following deliberate versions are known and standardized by this Technical Specification:
— Type V is a one-button hold-up device with a certain operating force for pressing the button;
— Type W is a one-button hold-up device with a removable cover and a certain operating force
for pressing the button;
— Type X is a two-button hold-up device, whereas both buttons need to be pressed with
individual operating forces to create a total operating force level;
— Type Y is a strip hold-up device with a certain operating force for pressing the strip;
— Type Z is a lever hold-up device with a certain operating force for pulling the lever.
If one or more operating member(s) of the hold-up device needs to be pressed, these should be flush
with or recessed in respect to the surrounding surfaces and should not be less than 15 mm in its
shortest diameter.
4.4.2 Operating forces
The type dependent operating forces shall apply according to Table 4:
Table 4 — Operating force for hand operated hold-up devices
Type of hold-up device
V W X Y Z
Minimum total operating force 5 N 4 N 4 N 5 N 5 N
Maximum total operating force 8 N 8 N 8 N 8 N 8 N
Maximum resetting threshold
a 3 N 3 N 3 N 3 N 3 N
when operating force is removed
a
This only applies for non-latching devices to restore the operating member(s) to the non-activated
position.
The operating forces shall be measured at the operating part or member(s) (e.g. buttons, lever or
strip). For hold-up devices of type X and Y, the total operating force shall correspond to the sum of the
operating forces on each individual operating member, which are required to create a hold-up trigger.
For non-latching devices, the device and its activated operating member(s) (e.g. button(s) or lever(s))
shall reset to the non-activated position when the applied operating force falls below the resetting
threshold given in Table 4.
---------------------- Page: 14 ----------------------
SIST-TS CLC/TS 50131-11:2012
- 13 - CLC/TS 50131-11:2012
4.4.3 Operating angle for type Z devices
If a type Z device operates on the principle of a pivoted lever, the performance requirements of this
subclause apply in addition to the requirements of 4.2.1.1.2.
To ensure a reliable, correct and usable operation type Z hold-up devices shall comply with the values
specified in Table 5. The manufacturer shall specify and describe the activation angle of the lever
hold-up device.
Table 5 — Minimum performance requirements for
hand operated lever hold-up devices
Angle
Minimum activation operating angle 20°
Maximum activation operating angle 45°
The minimum activation operating angle defines the maximum angle reached by pulling or lifting the
lever before which the device should not generate a hold-up trigger.
The maximum activation operating angle defines the maximum angle reached by pulling or lifting the
lever before which the device shall generate a hold-up trigger.
4.5 Kick / tilt & long bar operated devices
4.5.1 Manual deliberately trigger operation
Kick / tilt & long bar operated hold-up devices shall only generate a hold-up signal or message through
a deliberate manual operation. Means, methods or techniques shall be used to reduce the risk of
accidental operation of a Kick / Tilt or Long bar operated hold-up device (e.g. certain minimum force
required to press the bar), in accordance with this Technical Specification.
The following deliberate versions are known and standardised by this Technical Specification:
– Type A is operated by pressing down one or more operating member(s) with a certain operating
force, e.g. typically floor mounted and activated by foot;
– Type B is a foot operated device which is operated by lifting up one or more operating member(s)
with a certain operating force. The operating member(s) of that device should be at a distance
between 7 cm and 15 cm from the mounting surface in a condition when the hold-up device is
mounted according to the installation instructions of the manufacturer;
– Type C is a non-foot operated device which is operated by pressing one or more operating
member(s) with a certain operating force, e.g. typically mounted under the desk plate or mounted
vertically and activated by leg or knee.
4.5.2 Operating forces
The type dependent operating forces shall apply according to Table 6:
---------------------- Page: 15 ----------------------
SIST-TS CLC/TS 50131-11:2012
CLC/TS 50131-11:2012 - 14 -
Table 6 — Operating force for kick / tilt & long bar operated hold-up devices
Type of kick / tilt or long bar
operated hold-up device
A B & C
Minimum total operating force 20 N 5 N
Maximum total operating force 30 N 8 N
Maximum resetting threshold when operation
10 N 3 N
a
force is removed
a
This only applies for non-latching devices to restore the operating parts to the non-activated
position.
The operating forces shall be measured at each operating member(s) (e.g. bar).
If resetting applies to
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.