SIST EN 4595:2014
(Main)Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Subsonic erosion resistance
Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Subsonic erosion resistance
This European Standard specifies the requirements for a two component polyurethane, topcoat, with a medium degree of resistance to erosion by the effects of rain, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications on areas where rain erosion at subsonic speeds may be a problem e.g. leading edges and air intakes. The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met.
Luft- und Raumfahrt - Anstrichstoff - Zweikomponenten Polyurethan-Decklack, raumtemperaturhärtend - Unterschall-Erosionsbeständigkeit
Diese Europäische Norm legt die Anforderungen an einen Zwei-Komponenten-Polyurethan-Decklack mit mittlerer Beständigkeit gegenüber regenbedingter Erosion fest, den es mit einer Auswahl an Farbtönen und Glanzstufen gibt. Er wird auf eine Grundbeschichtung für Luft- und Raumfahrtanwendungen in Zonen, in denen Regenerosion bei Unterschallgeschwindigkeiten ein Problem darstellen kann, wie beispielsweise am Keilwinkel oder an Lufteintritten, aufgebracht.
Die in dieser Norm festgelegten Eigenschaften beziehen sich auf definierte Probekörpern aus einer Aluminiumlegierung, die nach EN 3837 Verfahren A und EN 23270 vorbereitet und mit einem Grundbeschichtungsstoff nach EN 2435 beschichtet werden. Die Tauglichkeit eines Werkstoffs für eine spezifische Anwendung (z. B. alternativer Untergrund, alternative Grundbeschichtungsstoff, spezifische Trocknungsbedingungen usw.) muss durch zusätzliche Prüfungen festgestellt werden, die bestätigen, dass die Anforderungen dieser Norm erfüllt sind.
Série aérospatiale - Peintures et vernis - Deux composants durcissement à froid, finition polyuréthane - Résistance à l’érosion subsonique
La présente Norme européenne spécifie les exigences d’une couche de finition polyuréthane, à deux composants, degré moyen de résistance à l’érosion liée aux effets de la pluie, disponible dans une gamme de couleurs et de niveaux de brillance, applicable sur une peinture primaire pour applications aérospatiales sur des zones où l’érosion par la pluie à des vitesses subsoniques peut constituer un problème par ex. bord d’attaque et entrées d’air.
Les propriétés spécifiées dans la présente norme sont obtenues sur des éprouvettes en alliage d’aluminium définies conformément à l’EN 3837 Procédure A et l’EN 23270 et peintes avec un primaire selon l’EN 2435. L’aptitude du matériau à être utilisé pour une application spécifique (par ex. subjectile alternatif, primaire alternative, conditions de séchage spécifiques, etc.) doit être déterminée par des essais complémentaires pour confirmer que les exigences de la présente norme sont satisfaites.
Aeronavtika - Barve in laki - Dvokomponentni poliuretanski končni premaz, ki se suši pri sobni temperaturi - Nizkofrekvenčna odpornost proti eroziji
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.LMLLuft- und Raumfahrt - Anstrichstoff - Zweikomponenten Polyurethan-Decklack, raumtemperaturhärtend - Unterschall-ErosionsbeständigkeitSérie aérospatiale - Peintures et vernis - Deux composants durcissement à froid, finition polyuréthane - Résistance à l’érosion subsoniqueAerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Subsonic erosion resistance49.040Prevleke in z njimi povezani postopki, ki se uporabljajo v letalski in vesoljski industrijiCoatings and related processes used in aerospace industryICS:Ta slovenski standard je istoveten z:EN 4595:2013SIST EN 4595:2014en01-februar-2014SIST EN 4595:2014SLOVENSKI
STANDARD
SIST EN 4595:2014
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4595
January 2013 ICS 49.040 English Version
Aerospace series - Paints and varnishes - Two component cold curing polyurethane finish - Subsonic erosion resistance
Série aérospatiale - Peintures et vernis - Deux composants durcissement à froid, finition polyuréthane - Résistance à l'érosion subsonique
Luft- und Raumfahrt - Beschichtungsstoffe - Zweikomponenten Polyurethan-Decklack, raumtemperaturhärtend - Unterschall-Erosionsbeständigkeit This European Standard was approved by CEN on 19 February 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4595:2013: ESIST EN 4595:2014
EN 4595:2013 (E) 2 Contents Page Foreword . 3 Introduction . 4 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 5 4 Classification . 5 5 Batch release and qualification testing . 5 5.1 Batch release testing . 5 5.2 Qualification tests . 5 6 Designation . 9
SIST EN 4595:2014
EN 4595:2013 (E) 3 Foreword This document (EN 4595:2013) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn at the latest by July 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 4595:2014
EN 4595:2013 (E) 4 Introduction This standard has been prepared in accordance with AECMA TR 7000-9. 1 Scope This European Standard specifies the requirements for a two component polyurethane, topcoat, with a medium degree of resistance to erosion by the effects of rain, available in a range of colours and levels of gloss, to be applied over a primer for aerospace applications on areas where rain erosion at subsonic speeds may be a problem e.g. leading edges and air intakes. The properties specified in this standard are obtained on defined aluminium alloy test pieces prepared in accordance with EN 3837 Procedure A and EN 23270 and painted with primer to EN 2435. The ability of the material to be used for a specific application (e.g. alternative substrate, alternative primer, specific drying conditions etc.) shall be determined by supplementary tests to confirm that the requirements of this standard are met. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2334, Aerospace series — Chromic-sulphuric acid pickle of aluminium and aluminium alloys EN 2379, Aerospace series — Fluids for assessment of non-metallic materials1) EN 2435 (all parts), Aerospace series — Paints and varnishes — Corrosion resistant chromated two component cold curing primer EN 3837, Aerospace series — Paints and varnishes — Nature and method for surface preparation of test pieces in aluminium alloys1) EN 3840, Aerospace series — Paints and varnishes — Technical specification EN 23270, Paints and varnishes and their raw materials — Temperatures and humidities for conditioning and testing (ISO 3270) EN
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.